.. _basic-setup: Basic Setup ============ After installing FRR, some basic configuration must be completed before it is ready to use. Crash logs ---------- If any daemon should crash for some reason (segmentation fault, assertion failure, etc.), it will attempt to write a backtrace to a file located in :file:`/var/tmp/frr/[-]./crashlog`. This feature is not affected by any configuration options. The crashlog file's directory also contains files corresponding to per-thread message buffers in files named :file:`/var/tmp/frr/[-]./logbuf.`. In case of a crash, these may contain unwritten buffered log messages. To show the contents of these buffers, pipe their contents through ``tr '\0' '\n'``. A blank line marks the end of valid unwritten data (it will generally be followed by garbled, older log messages since the buffer is not cleared.) Daemons Configuration File -------------------------- After a fresh install, starting FRR will do nothing. This is because daemons must be explicitly enabled by editing a file in your configuration directory. This file is usually located at :file:`/etc/frr/daemons` and determines which daemons are activated when issuing a service start / stop command via init or systemd. The file initially looks like this: :: zebra=no bgpd=no ospfd=no ospf6d=no ripd=no ripngd=no isisd=no pimd=no ldpd=no nhrpd=no eigrpd=no babeld=no sharpd=no staticd=no pbrd=no bfdd=no fabricd=no # # If this option is set the /etc/init.d/frr script automatically loads # the config via "vtysh -b" when the servers are started. # Check /etc/pam.d/frr if you intend to use "vtysh"! # vtysh_enable=yes zebra_options=" -s 90000000 --daemon -A 127.0.0.1" bgpd_options=" --daemon -A 127.0.0.1" ospfd_options=" --daemon -A 127.0.0.1" ospf6d_options=" --daemon -A ::1" ripd_options=" --daemon -A 127.0.0.1" ripngd_options=" --daemon -A ::1" isisd_options=" --daemon -A 127.0.0.1" pimd_options=" --daemon -A 127.0.0.1" ldpd_options=" --daemon -A 127.0.0.1" nhrpd_options=" --daemon -A 127.0.0.1" eigrpd_options=" --daemon -A 127.0.0.1" babeld_options=" --daemon -A 127.0.0.1" sharpd_options=" --daemon -A 127.0.0.1" staticd_options=" --daemon -A 127.0.0.1" pbrd_options=" --daemon -A 127.0.0.1" bfdd_options=" --daemon -A 127.0.0.1" fabricd_options=" --daemon -A 127.0.0.1" #MAX_FDS=1024 # The list of daemons to watch is automatically generated by the init script. #watchfrr_options="" # for debugging purposes, you can specify a "wrap" command to start instead # of starting the daemon directly, e.g. to use valgrind on ospfd: # ospfd_wrap="/usr/bin/valgrind" # or you can use "all_wrap" for all daemons, e.g. to use perf record: # all_wrap="/usr/bin/perf record --call-graph -" # the normal daemon command is added to this at the end. Breaking this file down: :: bgpd=yes To enable a particular daemon, simply change the corresponding 'no' to 'yes'. Subsequent service restarts should start the daemon. :: vtysh_enable=yes As the comment says, this causes :ref:`VTYSH ` to apply configuration when starting the daemons. This is useful for a variety of reasons touched on in the VTYSH documentation and should generally be enabled. :: MAX_FDS=1024 This allows the operator to control the number of open file descriptors each daemon is allowed to start with. The current assumed value on most operating systems is 1024. If the operator plans to run bgp with several thousands of peers than this is where we would modify FRR to allow this to happen. :: zebra_options=" -s 90000000 --daemon -A 127.0.0.1" bgpd_options=" --daemon -A 127.0.0.1" ... The next set of lines controls what options are passed to daemons when started from the service script. Usually daemons will have ``--daemon`` and ``-A
`` specified in order to daemonize and listen for VTY commands on a particular address. The remaining file content regarding `watchfrr_options` and `*_wrap` settings should not normally be needed; refer to the comments in case they are. Services -------- FRR daemons have their own terminal interface or VTY. After installation, it's a good idea to setup each daemon's port number to connect to them. To do this add the following entries to :file:`/etc/services`. :: zebrasrv 2600/tcp # zebra service zebra 2601/tcp # zebra vty ripd 2602/tcp # RIPd vty ripngd 2603/tcp # RIPngd vty ospfd 2604/tcp # OSPFd vty bgpd 2605/tcp # BGPd vty ospf6d 2606/tcp # OSPF6d vty ospfapi 2607/tcp # ospfapi isisd 2608/tcp # ISISd vty babeld 2609/tcp # BABELd vty nhrpd 2610/tcp # nhrpd vty pimd 2611/tcp # PIMd vty ldpd 2612/tcp # LDPd vty eigprd 2613/tcp # EIGRPd vty bfdd 2617/tcp # bfdd vty fabricd 2618/tcp # fabricd vty vrrpd 2619/tcp # vrrpd vty If you use a FreeBSD newer than 2.2.8, the above entries are already added to :file:`/etc/services` so there is no need to add it. If you specify a port number when starting the daemon, these entries may not be needed. You may need to make changes to the config files in |INSTALL_PREFIX_ETC|. Systemd ------- Although not installed when installing from source, FRR provides a service file for use with ``systemd``. It is located in :file:`tools/frr.service` in the Git repository. If ``systemctl status frr.service`` indicates that the FRR service is not found, copy the service file from the Git repository into your preferred location. A good place is usually ``/etc/systemd/system/``. After issuing a ``systemctl daemon-reload``, you should be able to start the FRR service via ``systemctl start frr``. If this fails, or no daemons are started. check the ``journalctl`` logs for an indication of what went wrong. Operations ---------- This section covers a few common operational tasks and how to perform them. Restarting ^^^^^^^^^^ Restarting kills all running FRR daemons and starts them again. Any unsaved configuration will be lost. .. code-block:: console service frr restart .. note:: Alternatively, you can invoke the init script directly:: /etc/init.d/frr restart Or, if using systemd:: systemctl restart frr Reloading ^^^^^^^^^ Reloading applies the differential between on-disk configuration and the current effective configuration of running FRR processes. This includes starting daemons that were previously stopped and any changes made to individual or unified daemon configuration files. .. code-block:: console service frr reload .. note:: Alternatively, you can invoke the init script directly:: /etc/init.d/frr reload Or, if using systemd:: systemctl reload frr See :ref:`FRR-RELOAD ` for more about the `frr-reload.py` script. Starting a new daemon ^^^^^^^^^^^^^^^^^^^^^ Suppose *bgpd* and *zebra* are running, and you wish to start *pimd*. In ``/etc/frr/daemons`` make the following change: .. code-block:: diff - pimd=no + pimd=yes Then perform a reload. Currently there is no way to stop or restart an individual daemon. This is because FRR's monitoring program cannot currently distinguish between a crashed / killed daemon versus one that has been intentionally stopped or restarted. The closest that can be achieved is to remove all configuration for the daemon, and set its line in ``/etc/frr/daemons`` to ``=no``. Once this is done, the daemon will be stopped the next time FRR is restarted. Network Namespaces ^^^^^^^^^^^^^^^^^^ It is possible to run FRR in different network namespaces so it can be further compartmentalized (e.g. confining to a smaller subset network). The network namespace configuration can be used in the default FRR configuration pathspace or it can be used in a different pathspace (`-N/--pathspace`). To use FRR network namespace in the default pathspace you should add or uncomment the ``watchfrr_options`` line in ``/etc/frr/daemons``: .. code-block:: diff - #watchfrr_options="--netns" + watchfrr_options="--netns=" If you want to use a different pathspace with the network namespace (the recommended way) you should add/uncomment the ``watchfrr_options`` line in ``/etc/frr//daemons``: .. code-block:: diff - #watchfrr_options="--netns" + #watchfrr_options="--netns=" + + # `--netns` argument is optional and if not provided it will + # default to the pathspace name. + watchfrr_options="--netns" To start FRR in the new pathspace+network namespace the initialization script should be called with an extra parameter: .. code:: /etc/init.d/frr start .. note:: Some Linux distributions might not use the default init script shipped with FRR, in that case you might want to try running the bundled script in ``/usr/lib/frr/frrinit.sh``. On systemd you might create different units or parameterize the existing one. See the man page: https://www.freedesktop.org/software/systemd/man/systemd.unit.html