blob: 6413c6299531639057335e3e559877498d55ae73 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
.. _ospfv3:
******
OSPFv3
******
*ospf6d* is a daemon support OSPF version 3 for IPv6 network. OSPF for IPv6 is
described in :rfc:`2740`.
.. _ospf6-router:
OSPF6 router
============
.. index:: router ospf6
.. clicmd:: router ospf6
.. index:: ospf6 router-id A.B.C.D
.. clicmd:: ospf6 router-id A.B.C.D
Set router's Router-ID.
.. index:: interface IFNAME area AREA
.. clicmd:: interface IFNAME area AREA
Bind interface to specified area, and start sending OSPF packets. `area` can
be specified as 0.
.. index:: timers throttle spf DELAY INITIAL-HOLDTIME MAX-HOLDTIME
.. clicmd:: timers throttle spf DELAY INITIAL-HOLDTIME MAX-HOLDTIME
.. index:: no timers throttle spf
.. clicmd:: no timers throttle spf
This command sets the initial `delay`, the `initial-holdtime`
and the `maximum-holdtime` between when SPF is calculated and the
event which triggered the calculation. The times are specified in
milliseconds and must be in the range of 0 to 600000 milliseconds.
The `delay` specifies the minimum amount of time to delay SPF
calculation (hence it affects how long SPF calculation is delayed after
an event which occurs outside of the holdtime of any previous SPF
calculation, and also serves as a minimum holdtime).
Consecutive SPF calculations will always be separated by at least
'hold-time' milliseconds. The hold-time is adaptive and initially is
set to the `initial-holdtime` configured with the above command.
Events which occur within the holdtime of the previous SPF calculation
will cause the holdtime to be increased by `initial-holdtime`, bounded
by the `maximum-holdtime` configured with this command. If the adaptive
hold-time elapses without any SPF-triggering event occurring then
the current holdtime is reset to the `initial-holdtime`.
.. code-block:: frr
router ospf6
timers throttle spf 200 400 10000
In this example, the `delay` is set to 200ms, the initial holdtime is set
to 400ms and the `maximum holdtime` to 10s. Hence there will always be at
least 200ms between an event which requires SPF calculation and the actual
SPF calculation. Further consecutive SPF calculations will always be
separated by between 400ms to 10s, the hold-time increasing by 400ms each
time an SPF-triggering event occurs within the hold-time of the previous
SPF calculation.
.. index:: auto-cost reference-bandwidth COST
.. clicmd:: auto-cost reference-bandwidth COST
.. index:: no auto-cost reference-bandwidth
.. clicmd:: no auto-cost reference-bandwidth
This sets the reference bandwidth for cost calculations, where this
bandwidth is considered equivalent to an OSPF cost of 1, specified in
Mbits/s. The default is 100Mbit/s (i.e. a link of bandwidth 100Mbit/s
or higher will have a cost of 1. Cost of lower bandwidth links will be
scaled with reference to this cost).
This configuration setting MUST be consistent across all routers
within the OSPF domain.
.. _ospf6-area:
OSPF6 area
==========
Area support for OSPFv3 is not yet implemented.
.. _ospf6-interface:
OSPF6 interface
===============
.. index:: ipv6 ospf6 cost COST
.. clicmd:: ipv6 ospf6 cost COST
Sets interface's output cost. Default value depends on the interface
bandwidth and on the auto-cost reference bandwidth.
.. index:: ipv6 ospf6 hello-interval HELLOINTERVAL
.. clicmd:: ipv6 ospf6 hello-interval HELLOINTERVAL
Sets interface's Hello Interval. Default 10
.. index:: ipv6 ospf6 dead-interval DEADINTERVAL
.. clicmd:: ipv6 ospf6 dead-interval DEADINTERVAL
Sets interface's Router Dead Interval. Default value is 40.
.. index:: ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
.. clicmd:: ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
Sets interface's Rxmt Interval. Default value is 5.
.. index:: ipv6 ospf6 priority PRIORITY
.. clicmd:: ipv6 ospf6 priority PRIORITY
Sets interface's Router Priority. Default value is 1.
.. index:: ipv6 ospf6 transmit-delay TRANSMITDELAY
.. clicmd:: ipv6 ospf6 transmit-delay TRANSMITDELAY
Sets interface's Inf-Trans-Delay. Default value is 1.
.. index:: ipv6 ospf6 network (broadcast|point-to-point)
.. clicmd:: ipv6 ospf6 network (broadcast|point-to-point)
Set explicitly network type for specified interface.
.. _redistribute-routes-to-ospf6:
Redistribute routes to OSPF6
============================
.. index:: redistribute static
.. clicmd:: redistribute static
.. index:: redistribute connected
.. clicmd:: redistribute connected
.. index:: redistribute ripng
.. clicmd:: redistribute ripng
.. _showing-ospf6-information:
Showing OSPF6 information
=========================
.. index:: show ipv6 ospf6 [INSTANCE_ID]
.. clicmd:: show ipv6 ospf6 [INSTANCE_ID]
INSTANCE_ID is an optional OSPF instance ID. To see router ID and OSPF
instance ID, simply type "show ipv6 ospf6 <cr>".
.. index:: show ipv6 ospf6 database
.. clicmd:: show ipv6 ospf6 database
This command shows LSA database summary. You can specify the type of LSA.
.. index:: show ipv6 ospf6 interface
.. clicmd:: show ipv6 ospf6 interface
To see OSPF interface configuration like costs.
.. index:: show ipv6 ospf6 neighbor
.. clicmd:: show ipv6 ospf6 neighbor
Shows state and chosen (Backup) DR of neighbor.
.. index:: show ipv6 ospf6 request-list A.B.C.D
.. clicmd:: show ipv6 ospf6 request-list A.B.C.D
Shows requestlist of neighbor.
.. index:: show ipv6 route ospf6
.. clicmd:: show ipv6 route ospf6
This command shows internal routing table.
.. index:: show ipv6 ospf6 zebra
.. clicmd:: show ipv6 ospf6 zebra
Shows state about what is being redistributed between zebra and OSPF6
OSPF6 Configuration Examples
============================
Example of ospf6d configured on one interface and area:
.. code-block:: frr
interface eth0
ipv6 ospf6 instance-id 0
!
router ospf6
router-id 212.17.55.53
area 0.0.0.0 range 2001:770:105:2::/64
interface eth0 area 0.0.0.0
!
|
