Merge tag 'for-5.13/libata-2021-04-27' of git://git.kernel.dk/linux-block

Pull libata updates from Jens Axboe:
 "Mostly cleanups this time, but also a few additions:

   - kernel-doc cleanups and sanitization (Lee)

   - Spelling fix (Bhaskar)

   - Fix ata_qc_from_tag() return value check in dwc_460ex (Dinghao)

   - Fall-through warning fix (Gustavo)

   - IRQ registration fixes (Sergey)

   - Add AHCI support for Tegra186 (Sowjanya)

   - Add xiling phy support for AHCI (Piyush)

   - SXS disable fix for AHCI for Hisilicon Kunpeng920 (Xingui)

   - pata legacy probe mask support (Maciej)"

* tag 'for-5.13/libata-2021-04-27' of git://git.kernel.dk/linux-block: (54 commits)
  libata: Fix fall-through warnings for Clang
  pata_ipx4xx_cf: Fix unsigned comparison with less than zero
  ata: ahci_tegra: call tegra_powergate_power_off only when PM domain is not present
  ata: ahci_tegra: Add AHCI support for Tegra186
  dt-binding: ata: tegra: Add dt-binding documentation for Tegra186
  dt-bindings: ata: tegra: Convert binding documentation to YAML
  pata_legacy: Add `probe_mask' parameter like with ide-generic
  pata_platform: Document `pio_mask' module parameter
  pata_legacy: Properly document module parameters
  ata: ahci: ceva: Updated code by using dev_err_probe()
  ata: ahci: Disable SXS for Hisilicon Kunpeng920
  ata: libahci_platform: fix IRQ check
  sata_mv: add IRQ checks
  ata: pata_acpi: Fix some incorrect function param descriptions
  ata: libata-acpi: Fix function name and provide description for 'prev_gtf'
  ata: sata_mv: Fix misnaming of 'mv_bmdma_stop()'
  ata: pata_cs5530: Fix misspelling of 'cs5530_init_one()'s 'pdev' param
  ata: pata_legacy: Repair a couple kernel-doc problems
  ata: ata_generic: Fix misspelling of 'ata_generic_init_one()'
  ata: pata_opti: Fix spelling issue of 'val' in 'opti_write_reg()'
  ...

47 files changed, 538 insertions, 167 deletions

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 74db44ce4d9a..5c949c12ed07 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -3600,6 +3600,96 @@
 			Currently this function knows 686a and 8231 chips.
 			Format: [spp|ps2|epp|ecp|ecpepp]
 
+	pata_legacy.all=	[HW,LIBATA]
+			Format: <int>
+			Set to non-zero to probe primary and secondary ISA
+			port ranges on PCI systems where no PCI PATA device
+			has been found at either range.  Disabled by default.
+
+	pata_legacy.autospeed=	[HW,LIBATA]
+			Format: <int>
+			Set to non-zero if a chip is present that snoops speed
+			changes.  Disabled by default.
+
+	pata_legacy.ht6560a=	[HW,LIBATA]
+			Format: <int>
+			Set to 1, 2, or 3 for HT 6560A on the primary channel,
+			the secondary channel, or both channels respectively.
+			Disabled by default.
+
+	pata_legacy.ht6560b=	[HW,LIBATA]
+			Format: <int>
+			Set to 1, 2, or 3 for HT 6560B on the primary channel,
+			the secondary channel, or both channels respectively.
+			Disabled by default.
+
+	pata_legacy.iordy_mask=	[HW,LIBATA]
+			Format: <int>
+			IORDY enable mask.  Set individual bits to allow IORDY
+			for the respective channel.  Bit 0 is for the first
+			legacy channel handled by this driver, bit 1 is for
+			the second channel, and so on.  The sequence will often
+			correspond to the primary legacy channel, the secondary
+			legacy channel, and so on, but the handling of a PCI
+			bus and the use of other driver options may interfere
+			with the sequence.  By default IORDY is allowed across
+			all channels.
+
+	pata_legacy.opti82c46x=	[HW,LIBATA]
+			Format: <int>
+			Set to 1, 2, or 3 for Opti 82c611A on the primary
+			channel, the secondary channel, or both channels
+			respectively.  Disabled by default.
+
+	pata_legacy.opti82c611a=	[HW,LIBATA]
+			Format: <int>
+			Set to 1, 2, or 3 for Opti 82c465MV on the primary
+			channel, the secondary channel, or both channels
+			respectively.  Disabled by default.
+
+	pata_legacy.pio_mask=	[HW,LIBATA]
+			Format: <int>
+			PIO mode mask for autospeed devices.  Set individual
+			bits to allow the use of the respective PIO modes.
+			Bit 0 is for mode 0, bit 1 is for mode 1, and so on.
+			All modes allowed by default.
+
+	pata_legacy.probe_all=	[HW,LIBATA]
+			Format: <int>
+			Set to non-zero to probe tertiary and further ISA
+			port ranges on PCI systems.  Disabled by default.
+
+	pata_legacy.probe_mask=	[HW,LIBATA]
+			Format: <int>
+			Probe mask for legacy ISA PATA ports.  Depending on
+			platform configuration and the use of other driver
+			options up to 6 legacy ports are supported: 0x1f0,
+			0x170, 0x1e8, 0x168, 0x1e0, 0x160, however probing
+			of individual ports can be disabled by setting the
+			corresponding bits in the mask to 1.  Bit 0 is for
+			the first port in the list above (0x1f0), and so on.
+			By default all supported ports are probed.
+
+	pata_legacy.qdi=	[HW,LIBATA]
+			Format: <int>
+			Set to non-zero to probe QDI controllers.  By default
+			set to 1 if CONFIG_PATA_QDI_MODULE, 0 otherwise.
+
+	pata_legacy.winbond=	[HW,LIBATA]
+			Format: <int>
+			Set to non-zero to probe Winbond controllers.  Use
+			the standard I/O port (0x130) if 1, otherwise the
+			value given is the I/O port to use (typically 0x1b0).
+			By default set to 1 if CONFIG_PATA_WINBOND_VLB_MODULE,
+			0 otherwise.
+
+	pata_platform.pio_mask=	[HW,LIBATA]
+			Format: <int>
+			Supported PIO mode mask.  Set individual bits to allow
+			the use of the respective PIO modes.  Bit 0 is for
+			mode 0, bit 1 is for mode 1, and so on.  Mode 0 only
+			allowed by default.
+
 	pause_on_oops=
 			Halt all CPUs after the first oops has been printed for
 			the specified number of seconds.  This is to be used if
diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
index 7561cc4de371..bfb6da0281ec 100644
--- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
@@ -38,6 +38,8 @@ Required properties:
 
 Optional properties:
   - ceva,broken-gen2: limit to gen1 speed instead of gen2.
+  - phys: phandle for the PHY device
+  - resets: phandle to the reset controller for the SATA IP
 
 Examples:
 	ahci@fd0c0000 {
@@ -56,4 +58,6 @@ Examples:
 		ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
 		ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
 		ceva,broken-gen2;
+		phys = <&psgtr 1 PHY_TYPE_SATA 1 1>;
+		resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
 	};
diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml b/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml
new file mode 100644
index 000000000000..a75e9a8f539a
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ata/nvidia,tegra-ahci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Tegra AHCI SATA Controller
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Jonathan Hunter <jonathanh@nvidia.com>
+
+properties:
+  compatible:
+    enum:
+      - nvidia,tegra124-ahci
+      - nvidia,tegra132-ahci
+      - nvidia,tegra210-ahci
+      - nvidia,tegra186-ahci
+
+  reg:
+    minItems: 2
+    maxItems: 3
+    items:
+      - description: AHCI registers
+      - description: SATA configuration and IPFS registers
+      - description: SATA AUX registers
+
+  interrupts:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: sata
+      - const: sata-oob
+
+  clocks:
+    maxItems: 2
+
+  reset-names:
+    minItems: 2
+    items:
+      - const: sata
+      - const: sata-cold
+      - const: sata-oob
+
+  resets:
+    minItems: 2
+    maxItems: 3
+
+  iommus:
+    maxItems: 1
+
+  interconnect-names:
+    items:
+      - const: dma-mem
+      - const: write
+
+  interconnects:
+    maxItems: 2
+
+  power-domains:
+    items:
+      - description: SAX power-domain
+
+  phy-names:
+    items:
+      - const: sata-0
+
+  phys:
+    maxItems: 1
+
+  hvdd-supply:
+    description: SATA HVDD regulator supply.
+
+  vddio-supply:
+    description: SATA VDDIO regulator supply.
+
+  avdd-supply:
+    description: SATA AVDD regulator supply.
+
+  target-5v-supply:
+    description: SATA 5V power regulator supply.
+
+  target-12v-supply:
+    description: SATA 12V power regulator supply.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clock-names
+  - clocks
+  - reset-names
+  - resets
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - nvidia,tegra124-ahci
+              - nvidia,tegra132-ahci
+    then:
+      properties:
+        reg:
+          maxItems: 2
+        reset-names:
+          minItems: 3
+        resets:
+          minItems: 3
+      required:
+        - phys
+        - phy-names
+        - hvdd-supply
+        - vddio-supply
+        - avdd-supply
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - nvidia,tegra210-ahci
+    then:
+      properties:
+        reg:
+          minItems: 3
+        reset-names:
+          minItems: 3
+        resets:
+          minItems: 3
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - nvidia,tegra186-ahci
+    then:
+      properties:
+        reg:
+          minItems: 3
+        reset-names:
+          maxItems: 2
+        resets:
+          maxItems: 2
+      required:
+        - iommus
+        - interconnect-names
+        - interconnects
+        - power-domains
+
+additionalProperties: true
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra210-car.h>
+    #include <dt-bindings/reset/tegra210-car.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    sata@70020000 {
+            compatible = "nvidia,tegra210-ahci";
+            reg = <0x70027000 0x00002000>, /* AHCI */
+                  <0x70020000 0x00007000>, /* SATA */
+                  <0x70001100 0x00010000>; /* SATA AUX */
+            interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&tegra_car TEGRA210_CLK_SATA>,
+                     <&tegra_car TEGRA210_CLK_SATA_OOB>;
+            clock-names = "sata", "sata-oob";
+            resets = <&tegra_car 124>,
+                     <&tegra_car 129>,
+                     <&tegra_car 123>;
+            reset-names = "sata", "sata-cold", "sata-oob";
+    };
diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt
deleted file mode 100644
index 12ab2f723eb0..000000000000
--- a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt
+++ /dev/null
@@ -1,44 +0,0 @@
-Tegra SoC SATA AHCI controller
-
-Required properties :
-- compatible : Must be one of:
-  - Tegra124 : "nvidia,tegra124-ahci"
-  - Tegra132 : "nvidia,tegra132-ahci", "nvidia,tegra124-ahci"
-  - Tegra210 : "nvidia,tegra210-ahci"
-- reg : Should contain 2 entries:
-  - AHCI register set (SATA BAR5)
-  - SATA register set
-- interrupts : Defines the interrupt used by SATA
-- clocks : Must contain an entry for each entry in clock-names.
-  See ../clocks/clock-bindings.txt for details.
-- clock-names : Must include the following entries:
-  - sata
-  - sata-oob
-- resets : Must contain an entry for each entry in reset-names.
-  See ../reset/reset.txt for details.
-- reset-names : Must include the following entries:
-  - sata
-  - sata-oob
-  - sata-cold
-- phys : Must contain an entry for each entry in phy-names.
-  See ../phy/phy-bindings.txt for details.
-- phy-names : Must include the following entries:
-  - For Tegra124 and Tegra132:
-    - sata-phy : XUSB PADCTL SATA PHY
-- For Tegra124 and Tegra132:
-  - hvdd-supply : Defines the SATA HVDD regulator
-  - vddio-supply : Defines the SATA VDDIO regulator
-  - avdd-supply : Defines the SATA AVDD regulator
-  - target-5v-supply : Defines the SATA 5V power regulator
-  - target-12v-supply : Defines the SATA 12V power regulator
-
-Optional properties:
-- reg :
-  - AUX register set
-- clock-names :
-  - cml1 :
-    cml1 clock should be defined here if the PHY driver
-    doesn't manage them. If it does, they should not be.
-- phy-names :
-  - For T210:
-    - sata-phy
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 00ba8e5a1ccc..33192a8f687d 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1772,6 +1772,11 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 		hpriv->flags |= AHCI_HFLAG_NO_DEVSLP;
 
 #ifdef CONFIG_ARM64
+	if (pdev->vendor == PCI_VENDOR_ID_HUAWEI &&
+	    pdev->device == 0xa235 &&
+	    pdev->revision < 0x30)
+		hpriv->flags |= AHCI_HFLAG_NO_SXS;
+
 	if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
 		hpriv->irq_handler = ahci_thunderx_irq_handler;
 #endif
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 98b8baa47dc5..d1f284f0c83d 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -242,6 +242,7 @@ enum {
 							suspend/resume */
 	AHCI_HFLAG_IGN_NOTSUPP_POWER_ON	= (1 << 27), /* ignore -EOPNOTSUPP
 							from phy_power_on() */
+	AHCI_HFLAG_NO_SXS		= (1 << 28), /* SXS not supported */
 
 	/* ap->flags bits */
 
diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c
index b10fd4c8c853..50b56cd0039d 100644
--- a/drivers/ata/ahci_ceva.c
+++ b/drivers/ata/ahci_ceva.c
@@ -12,6 +12,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reset.h>
 #include "ahci.h"
 
 /* Vendor Specific Register Offsets */
@@ -87,6 +88,7 @@ struct ceva_ahci_priv {
 	u32 axicc;
 	bool is_cci_enabled;
 	int flags;
+	struct reset_control *rst;
 };
 
 static unsigned int ceva_ahci_read_id(struct ata_device *dev,
@@ -202,13 +204,46 @@ static int ceva_ahci_probe(struct platform_device *pdev)
 
 	cevapriv->ahci_pdev = pdev;
 
+	cevapriv->rst = devm_reset_control_get_optional_exclusive(&pdev->dev,
+								  NULL);
+	if (IS_ERR(cevapriv->rst))
+		dev_err_probe(&pdev->dev, PTR_ERR(cevapriv->rst),
+			      "failed to get reset\n");
+
 	hpriv = ahci_platform_get_resources(pdev, 0);
 	if (IS_ERR(hpriv))
 		return PTR_ERR(hpriv);
 
-	rc = ahci_platform_enable_resources(hpriv);
-	if (rc)
-		return rc;
+	if (!cevapriv->rst) {
+		rc = ahci_platform_enable_resources(hpriv);
+		if (rc)
+			return rc;
+	} else {
+		int i;
+
+		rc = ahci_platform_enable_clks(hpriv);
+		if (rc)
+			return rc;
+		/* Assert the controller reset */
+		reset_control_assert(cevapriv->rst);
+
+		for (i = 0; i < hpriv->nports; i++) {
+			rc = phy_init(hpriv->phys[i]);
+			if (rc)
+				return rc;
+		}
+
+		/* De-assert the controller reset */
+		reset_control_deassert(cevapriv->rst);
+
+		for (i = 0; i < hpriv->nports; i++) {
+			rc = phy_power_on(hpriv->phys[i]);
+			if (rc) {
+				phy_exit(hpriv->phys[i]);
+				return rc;
+			}
+		}
+	}
 
 	if (of_property_read_bool(np, "ceva,broken-gen2"))
 		cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
index cb55ebc1725b..4fb94db1217d 100644
--- a/drivers/ata/ahci_tegra.c
+++ b/drivers/ata/ahci_tegra.c
@@ -59,8 +59,6 @@
 #define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN		BIT(22)
 
 #define T_SATA0_NVOOB                                   0x114
-#define T_SATA0_NVOOB_COMMA_CNT_MASK                    (0xff << 16)
-#define T_SATA0_NVOOB_COMMA_CNT                         (0x07 << 16)
 #define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK          (0x3 << 24)
 #define T_SATA0_NVOOB_SQUELCH_FILTER_MODE               (0x1 << 24)
 #define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK        (0x3 << 26)
@@ -154,11 +152,18 @@ struct tegra_ahci_ops {
 	int (*init)(struct ahci_host_priv *hpriv);
 };
 
+struct tegra_ahci_regs {
+	unsigned int nvoob_comma_cnt_mask;
+	unsigned int nvoob_comma_cnt_val;
+};
+
 struct tegra_ahci_soc {
 	const char *const		*supply_names;
 	u32				num_supplies;
 	bool				supports_devslp;
+	bool				has_sata_oob_rst;
 	const struct tegra_ahci_ops	*ops;
+	const struct tegra_ahci_regs	*regs;
 };
 
 struct tegra_ahci_priv {
@@ -240,11 +245,13 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
 	if (ret)
 		return ret;
 
-	ret = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_SATA,
-						tegra->sata_clk,
-						tegra->sata_rst);
-	if (ret)
-		goto disable_regulators;
+	if (!tegra->pdev->dev.pm_domain) {
+		ret = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_SATA,
+							tegra->sata_clk,
+							tegra->sata_rst);
+		if (ret)
+			goto disable_regulators;
+	}
 
 	reset_control_assert(tegra->sata_oob_rst);
 	reset_control_assert(tegra->sata_cold_rst);
@@ -261,7 +268,8 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
 disable_power:
 	clk_disable_unprepare(tegra->sata_clk);
 
-	tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
+	if (!tegra->pdev->dev.pm_domain)
+		tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
 
 disable_regulators:
 	regulator_bulk_disable(tegra->soc->num_supplies, tegra->supplies);
@@ -280,7 +288,8 @@ static void tegra_ahci_power_off(struct ahci_host_priv *hpriv)
 	reset_control_assert(tegra->sata_cold_rst);
 
 	clk_disable_unprepare(tegra->sata_clk);
-	tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
+	if (!tegra->pdev->dev.pm_domain)
+		tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
 
 	regulator_bulk_disable(tegra->soc->num_supplies, tegra->supplies);
 }
@@ -330,10 +339,10 @@ static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv)
 	writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
 
 	val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
-	val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK |
+	val &= ~(tegra->soc->regs->nvoob_comma_cnt_mask |
 		 T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK |
 		 T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK);
-	val |= (T_SATA0_NVOOB_COMMA_CNT |
+	val |= (tegra->soc->regs->nvoob_comma_cnt_val |
 		T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH |
 		T_SATA0_NVOOB_SQUELCH_FILTER_MODE);
 	writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
@@ -449,15 +458,35 @@ static const struct tegra_ahci_ops tegra124_ahci_ops = {
 	.init = tegra124_ahci_init,
 };
 
+static const struct tegra_ahci_regs tegra124_ahci_regs = {
+	.nvoob_comma_cnt_mask = GENMASK(30, 28),
+	.nvoob_comma_cnt_val = (7 << 28),
+};
+
 static const struct tegra_ahci_soc tegra124_ahci_soc = {
 	.supply_names = tegra124_supply_names,
 	.num_supplies = ARRAY_SIZE(tegra124_supply_names),
 	.supports_devslp = false,
+	.has_sata_oob_rst = true,
 	.ops = &tegra124_ahci_ops,
+	.regs = &tegra124_ahci_regs,
 };
 
 static const struct tegra_ahci_soc tegra210_ahci_soc = {
 	.supports_devslp = false,
+	.has_sata_oob_rst = true,
+	.regs = &tegra124_ahci_regs,
+};
+
+static const struct tegra_ahci_regs tegra186_ahci_regs = {
+	.nvoob_comma_cnt_mask = GENMASK(23, 16),
+	.nvoob_comma_cnt_val = (7 << 16),
+};
+
+static const struct tegra_ahci_soc tegra186_ahci_soc = {
+	.supports_devslp = false,
+	.has_sata_oob_rst = false,
+	.regs = &tegra186_ahci_regs,
 };
 
 static const struct of_device_id tegra_ahci_of_match[] = {
@@ -469,6 +498,10 @@ static const struct of_device_id tegra_ahci_of_match[] = {
 		.compatible = "nvidia,tegra210-ahci",
 		.data = &tegra210_ahci_soc
 	},
+	{
+		.compatible = "nvidia,tegra186-ahci",
+		.data = &tegra186_ahci_soc
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, tegra_ahci_of_match);
@@ -518,10 +551,13 @@ static int tegra_ahci_probe(struct platform_device *pdev)
 		return PTR_ERR(tegra->sata_rst);
 	}
 
-	tegra->sata_oob_rst = devm_reset_control_get(&pdev->dev, "sata-oob");
-	if (IS_ERR(tegra->sata_oob_rst)) {
-		dev_err(&pdev->dev, "Failed to get sata-oob reset\n");
-		return PTR_ERR(tegra->sata_oob_rst);
+	if (tegra->soc->has_sata_oob_rst) {
+		tegra->sata_oob_rst = devm_reset_control_get(&pdev->dev,
+							     "sata-oob");
+		if (IS_ERR(tegra->sata_oob_rst)) {
+			dev_err(&pdev->dev, "Failed to get sata-oob reset\n");
+			return PTR_ERR(tegra->sata_oob_rst);
+		}
 	}
 
 	tegra->sata_cold_rst = devm_reset_control_get(&pdev->dev, "sata-cold");
diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c
index 16246c843365..dffc432b9d54 100644
--- a/drivers/ata/ahci_xgene.c
+++ b/drivers/ata/ahci_xgene.c
@@ -537,7 +537,7 @@ softreset_retry:
 
 /**
  * xgene_ahci_handle_broken_edge_irq - Handle the broken irq.
- * @ata_host: Host that recieved the irq
+ * @host: Host that recieved the irq
  * @irq_masked: HOST_IRQ_STAT value
  *
  * For hardware with broken edge trigger latch
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 9ff545ce8da3..20a32e4d501d 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -151,7 +151,7 @@ static int is_intel_ider(struct pci_dev *dev)
 }
 
 /**
- *	ata_generic_init		-	attach generic IDE
+ *	ata_generic_init_one		-	attach generic IDE
  *	@dev: PCI device found
  *	@id: match entry
  *
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index ea5bf5f4cbed..fec2e9754aed 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -493,6 +493,11 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
 		cap |= HOST_CAP_ALPM;
 	}
 
+	if ((cap & HOST_CAP_SXS) && (hpriv->flags & AHCI_HFLAG_NO_SXS)) {
+		dev_info(dev, "controller does not support SXS, disabling CAP_SXS\n");
+		cap &= ~HOST_CAP_SXS;
+	}
+
 	if (hpriv->force_port_map && port_map != hpriv->force_port_map) {
 		dev_info(dev, "forcing port_map 0x%x -> 0x%x\n",
 			 port_map, hpriv->force_port_map);
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
index de638dafce21..b2f552088291 100644
--- a/drivers/ata/libahci_platform.c
+++ b/drivers/ata/libahci_platform.c
@@ -582,11 +582,13 @@ int ahci_platform_init_host(struct platform_device *pdev,
 	int i, irq, n_ports, rc;
 
 	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
+	if (irq < 0) {
 		if (irq != -EPROBE_DEFER)
 			dev_err(dev, "no irq\n");
 		return irq;
 	}
+	if (!irq)
+		return -EINVAL;
 
 	hpriv->irq = irq;
 
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index 224e3486e9a5..7a7d6642edcc 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -476,7 +476,7 @@ static int ata_dev_get_GTF(struct ata_device *dev, struct ata_acpi_gtf **gtf)
 }
 
 /**
- * ata_acpi_gtm_xfermode - determine xfermode from GTM parameter
+ * ata_acpi_gtm_xfermask - determine xfermode from GTM parameter
  * @dev: target device
  * @gtm: GTM parameter to use
  *
@@ -624,6 +624,7 @@ static int ata_acpi_filter_tf(struct ata_device *dev,
  * ata_acpi_run_tf - send taskfile registers to host controller
  * @dev: target ATA device
  * @gtf: raw ATA taskfile register set (0x1f1 - 0x1f7)
+ * @prev_gtf: previous command
  *
  * Outputs ATA taskfile to standard ATA host controller.
  * Writes the control, feature, nsect, lbal, lbam, and lbah registers.
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index b6f92050e60c..2db1e9c66088 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2613,6 +2613,7 @@ int ata_eh_reset(struct ata_link *link, int classify,
 			switch (tmp) {
 			case -EAGAIN:
 				rc = -EAGAIN;
+				break;
 			case 0:
 				break;
 			default:
diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c
index 79f2aeeb482a..ba7be3f38617 100644
--- a/drivers/ata/libata-pmp.c
+++ b/drivers/ata/libata-pmp.c
@@ -62,7 +62,7 @@ static unsigned int sata_pmp_read(struct ata_link *link, int reg, u32 *r_val)
  *	sata_pmp_write - write PMP register
  *	@link: link to write PMP register for
  *	@reg: register to write
- *	@r_val: value to write
+ *	@val: value to write
  *
  *	Write PMP register.
  *
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index c16423e44525..8adeab76dd38 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -1067,7 +1067,7 @@ int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
 EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
 
 /**
- *	port_alloc - Allocate port for a SAS attached SATA device
+ *	ata_sas_port_alloc - Allocate port for a SAS attached SATA device
  *	@host: ATA host container for all SAS ports
  *	@port_info: Information from low-level host driver
  *	@shost: SCSI host that the scsi device is attached to
@@ -1127,7 +1127,7 @@ int ata_sas_port_start(struct ata_port *ap)
 EXPORT_SYMBOL_GPL(ata_sas_port_start);
 
 /**
- *	ata_port_stop - Undo ata_sas_port_start()
+ *	ata_sas_port_stop - Undo ata_sas_port_start()
  *	@ap: Port to shut down
  *
  *	May be used as the port_stop() entry in ata_port_operations.
diff --git a/drivers/ata/libata-transport.c b/drivers/ata/libata-transport.c
index 6a40e3c6cf49..34bb4608bdc6 100644
--- a/drivers/ata/libata-transport.c
+++ b/drivers/ata/libata-transport.c
@@ -250,7 +250,7 @@ static int ata_tport_match(struct attribute_container *cont,
 
 /**
  * ata_tport_delete  --  remove ATA PORT
- * @port:	ATA PORT to remove
+ * @ap:	ATA PORT to remove
  *
  * Removes the specified ATA PORT.  Remove the associated link as well.
  */
@@ -376,7 +376,7 @@ static int ata_tlink_match(struct attribute_container *cont,
 
 /**
  * ata_tlink_delete  --  remove ATA LINK
- * @port:	ATA LINK to remove
+ * @link:	ATA LINK to remove
  *
  * Removes the specified ATA LINK.  remove associated ATA device(s) as well.
  */
@@ -632,7 +632,7 @@ static void ata_tdev_free(struct ata_device *dev)
 
 /**
  * ata_tdev_delete  --  remove ATA device
- * @port:	ATA PORT to remove
+ * @ata_dev:	ATA device to remove
  *
  * Removes the specified ATA device.
  */
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index fa2bfc344a97..ade4c3eee230 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -28,7 +28,7 @@ struct pata_acpi {
 
 /**
  *	pacpi_pre_reset	-	check for 40/80 pin
- *	@ap: Port
+ *	@link: ATA link
  *	@deadline: deadline jiffies for the operation
  *
  *	Perform the PATA port setup we need.
@@ -63,8 +63,8 @@ static int pacpi_cable_detect(struct ata_port *ap)
 
 /**
  *	pacpi_discover_modes	-	filter non ACPI modes
+ *	@ap: ATA port
  *	@adev: ATA device
- *	@mask: proposed modes
  *
  *	Try the modes available and see which ones the ACPI method will
  *	set up sensibly. From this we get a mask of ACPI modes we can use
@@ -224,7 +224,7 @@ static struct ata_port_operations pacpi_ops = {
 /**
  *	pacpi_init_one - Register ACPI ATA PCI device with kernel services
  *	@pdev: PCI device to register
- *	@ent: Entry in pacpi_pci_tbl matching with @pdev
+ *	@id: PCI device ID
  *
  *	Called from kernel PCI layer.
  *
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 0b122f903b8a..557ecf466102 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -108,8 +108,8 @@ static int ali_c2_cable_detect(struct ata_port *ap)
 
 /**
  *	ali_20_filter		-	filter for earlier ALI DMA
- *	@ap: ALi ATA port
- *	@adev: attached device
+ *	@adev: ATA device
+ *	@mask: received mask to manipulate and pass back
  *
  *	Ensure that we do not do DMA on CD devices. We may be able to
  *	fix that later on. Also ensure we do not do UDMA on WDC drives
@@ -313,7 +313,7 @@ static void ali_lock_sectors(struct ata_device *adev)
 
 /**
  *	ali_check_atapi_dma	-	DMA check for most ALi controllers
- *	@adev: Device
+ *	@qc: Command to complete
  *
  *	Called to decide whether commands should be sent by DMA or PIO
  */
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 987967f976cb..c8acba162d02 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -167,7 +167,6 @@ static int amd_cable_detect(struct ata_port *ap)
 /**
  *	amd_fifo_setup		-	set the PIO FIFO for ATA/ATAPI
  *	@ap: ATA interface
- *	@adev: ATA device
  *
  *	Set the PCI fifo for this device according to the devices present
  *	on the bus at this point in time. We need to turn the post write buffer
@@ -320,8 +319,9 @@ static unsigned long nv_mode_filter(struct ata_device *dev,
 }
 
 /**
- *	nv_probe_init	-	cable detection
- *	@lin: ATA link
+ *	nv_pre_reset	-	cable detection
+ *	@link: ATA link
+ *	@deadline: deadline jiffies for the operation
  *
  *	Perform cable detection. The BIOS stores this in PCI config
  *	space for us.
diff --git a/drivers/ata/pata_arasan_cf.c b/drivers/ata/pata_arasan_cf.c
index e9cf31f38450..63f39440a9b4 100644
--- a/drivers/ata/pata_arasan_cf.c
+++ b/drivers/ata/pata_arasan_cf.c
@@ -818,12 +818,19 @@ static int arasan_cf_probe(struct platform_device *pdev)
 	else
 		quirk = CF_BROKEN_UDMA; /* as it is on spear1340 */
 
-	/* if irq is 0, support only PIO */
-	acdev->irq = platform_get_irq(pdev, 0);
-	if (acdev->irq)
+	/*
+	 * If there's an error getting IRQ (or we do get IRQ0),
+	 * support only PIO
+	 */
+	ret = platform_get_irq(pdev, 0);
+	if (ret > 0) {
+		acdev->irq = ret;
 		irq_handler = arasan_cf_interrupt;
-	else
+	} else	if (ret == -EPROBE_DEFER) {
+		return ret;
+	} else	{
 		quirk |= CF_BROKEN_MWDMA | CF_BROKEN_UDMA;
+	}
 
 	acdev->pbase = res->start;
 	acdev->vbase = devm_ioremap(&pdev->dev, res->start,
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 6bd2228bb6ff..ad3c5808aaad 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -268,7 +268,7 @@ static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	artop_6210_qc_defer	-	implement serialization
+ *	artop6210_qc_defer	-	implement serialization
  *	@qc: command
  *
  *	Issue commands per host on this chip.
@@ -344,7 +344,7 @@ static void atp8xx_fixup(struct pci_dev *pdev)
 /**
  *	artop_init_one - Register ARTOP ATA PCI device with kernel services
  *	@pdev: PCI device to register
- *	@ent: Entry in artop_pci_tbl matching with @pdev
+ *	@id: PCI device ID
  *
  *	Called from kernel PCI layer.
  *
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index c68aa3f585f2..d671d33ef287 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -93,6 +93,7 @@ static int atiixp_prereset(struct ata_link *link, unsigned long deadline)
  *	atiixp_set_pio_timing	-	set initial PIO mode data
  *	@ap: ATA interface
  *	@adev: ATA device
+ *	@pio: Requested PIO
  *
  *	Called by both the pio and dma setup functions to set the controller
  *	timings for PIO transfers. We must load both the mode number and
@@ -227,7 +228,7 @@ static void atiixp_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	atiixp_dma_stop	-	DMA stop callback
+ *	atiixp_bmdma_stop	-	DMA stop callback
  *	@qc: Command in progress
  *
  *	DMA has completed. Clear the UDMA flag as the next operations will
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 9052148b306d..d09d432d3c44 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -52,6 +52,7 @@ static const struct pio_clocks cs5520_pio_clocks[]={
  *	cs5520_set_timings	-	program PIO timings
  *	@ap: ATA port
  *	@adev: ATA device
+ *	@pio: PIO ID
  *
  *	Program the PIO mode timings for the controller according to the pio
  *	clocking table.
@@ -246,6 +247,7 @@ static int cs5520_reinit_one(struct pci_dev *pdev)
 /**
  *	cs5520_pci_device_suspend	-	device suspend
  *	@pdev: PCI device
+ *	@mesg: PM event message
  *
  *	We have to cut and waste bits from the standard method because
  *	the 5520 is a bit odd and not just a pure ATA device. As a result
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index ad75d02b6dac..a1b4aaccaa50 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -271,7 +271,7 @@ fail_put:
 
 /**
  *	cs5530_init_one		-	Initialise a CS5530
- *	@dev: PCI device
+ *	@pdev: PCI device
  *	@id: Entry in match table
  *
  *	Install a driver for the newly found CS5530 companion chip. Most of
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 2574d6fbb1ad..06b7c4a9ec95 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -192,6 +192,7 @@ static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
 /**
  *	hpt366_filter	-	mode selection filter
  *	@adev: ATA device
+ *	@mask: Current mask to manipulate and pass back
  *
  *	Block UDMA on devices that cause trouble with this controller.
  */
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index fad6c6a87313..f242157bc81b 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -275,6 +275,7 @@ static const char * const bad_ata100_5[] = {
 /**
  *	hpt370_filter	-	mode selection filter
  *	@adev: ATA device
+ *	@mask: mode mask
  *
  *	Block UDMA on devices that cause trouble with this controller.
  */
@@ -293,6 +294,7 @@ static unsigned long hpt370_filter(struct ata_device *adev, unsigned long mask)
 /**
  *	hpt370a_filter	-	mode selection filter
  *	@adev: ATA device
+ *	@mask: mode mask
  *
  *	Block UDMA on devices that cause trouble with this controller.
  */
@@ -463,7 +465,7 @@ static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	hpt370_bmdma_end		-	DMA engine stop
+ *	hpt370_bmdma_stop		-	DMA engine stop
  *	@qc: ATA command
  *
  *	Work around the HPT370 DMA engine.
@@ -557,7 +559,7 @@ static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	hpt37x_bmdma_end		-	DMA engine stop
+ *	hpt37x_bmdma_stop		-	DMA engine stop
  *	@qc: ATA command
  *
  *	Clean up after the HPT372 and later DMA engine
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 9cb2d50db876..48eef338e050 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -237,7 +237,7 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	hpt3x2n_bmdma_end		-	DMA engine stop
+ *	hpt3x2n_bmdma_stop		-	DMA engine stop
  *	@qc: ATA command
  *
  *	Clean up after the HPT3x2n and later DMA engine
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 9bac79edbc2c..0e2265978a34 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -334,7 +334,7 @@ static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *
 }
 
 /**
- *	it821x_passthru_dma_start	-	DMA start callback
+ *	it821x_passthru_bmdma_start	-	DMA start callback
  *	@qc: Command in progress
  *
  *	Usually drivers set the DMA timing at the point the set_dmamode call
@@ -357,7 +357,7 @@ static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	it821x_passthru_dma_stop	-	DMA stop callback
+ *	it821x_passthru_bmdma_stop	-	DMA stop callback
  *	@qc: ATA command
  *
  *	We loaded new timings in dma_start, as a result we need to restore
diff --git a/drivers/ata/pata_ixp4xx_cf.c b/drivers/ata/pata_ixp4xx_cf.c
index d1644a8ef9fa..43215a4c1e54 100644
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -135,12 +135,12 @@ static void ixp4xx_setup_port(struct ata_port *ap,
 
 static int ixp4xx_pata_probe(struct platform_device *pdev)
 {
-	unsigned int irq;
 	struct resource *cs0, *cs1;
 	struct ata_host *host;
 	struct ata_port *ap;
 	struct ixp4xx_pata_data *data = dev_get_platdata(&pdev->dev);
 	int ret;
+	int irq;
 
 	cs0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	cs1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
@@ -165,8 +165,12 @@ static int ixp4xx_pata_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	irq = platform_get_irq(pdev, 0);
-	if (irq)
+	if (irq > 0)
 		irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING);
+	else if (irq < 0)
+		return irq;
+	else
+		return -EINVAL;
 
 	/* Setup expansion bus chip selects */
 	*data->cs0_cfg = data->cs0_bits;
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index c3dedd3e71fb..d1b3ce8958dd 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -120,7 +120,7 @@ static struct ata_port_operations jmicron_ops = {
 /**
  *	jmicron_init_one - Register Jmicron ATA PCI device with kernel services
  *	@pdev: PCI device to register
- *	@ent: Entry in jmicron_pci_tbl matching with @pdev
+ *	@id: PCI device ID
  *
  *	Called from kernel PCI layer.
  *
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 4fd12b20df23..c3e6592712c4 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -63,7 +63,66 @@
 
 static int all;
 module_param(all, int, 0444);
-MODULE_PARM_DESC(all, "Grab all legacy port devices, even if PCI(0=off, 1=on)");
+MODULE_PARM_DESC(all,
+		 "Set to probe unclaimed pri/sec ISA port ranges even if PCI");
+
+static int probe_all;
+module_param(probe_all, int, 0);
+MODULE_PARM_DESC(probe_all,
+		 "Set to probe tertiary+ ISA port ranges even if PCI");
+
+static int probe_mask = ~0;
+module_param(probe_mask, int, 0);
+MODULE_PARM_DESC(probe_mask, "Probe mask for legacy ISA PATA ports");
+
+static int autospeed;
+module_param(autospeed, int, 0);
+MODULE_PARM_DESC(autospeed, "Chip present that snoops speed changes");
+
+static int pio_mask = ATA_PIO4;
+module_param(pio_mask, int, 0);
+MODULE_PARM_DESC(pio_mask, "PIO range for autospeed devices");
+
+static int iordy_mask = 0xFFFFFFFF;
+module_param(iordy_mask, int, 0);
+MODULE_PARM_DESC(iordy_mask, "Use IORDY if available");
+
+static int ht6560a;
+module_param(ht6560a, int, 0);
+MODULE_PARM_DESC(ht6560a, "HT 6560A on primary 1, second 2, both 3");
+
+static int ht6560b;
+module_param(ht6560b, int, 0);
+MODULE_PARM_DESC(ht6560b, "HT 6560B on primary 1, secondary 2, both 3");
+
+static int opti82c611a;
+module_param(opti82c611a, int, 0);
+MODULE_PARM_DESC(opti82c611a,
+		 "Opti 82c611A on primary 1, secondary 2, both 3");
+
+static int opti82c46x;
+module_param(opti82c46x, int, 0);
+MODULE_PARM_DESC(opti82c46x,
+		 "Opti 82c465MV on primary 1, secondary 2, both 3");
+
+#ifdef CONFIG_PATA_QDI_MODULE
+static int qdi = 1;
+#else
+static int qdi;
+#endif
+module_param(qdi, int, 0);
+MODULE_PARM_DESC(qdi, "Set to probe QDI controllers");
+
+#ifdef CONFIG_PATA_WINBOND_VLB_MODULE
+static int winbond = 1;
+#else
+static int winbond;
+#endif
+module_param(winbond, int, 0);
+MODULE_PARM_DESC(winbond,
+		 "Set to probe Winbond controllers, "
+		 "give I/O port if non standard");
+
 
 enum controller {
 	BIOS = 0,
@@ -117,30 +176,6 @@ static struct ata_host *legacy_host[NR_HOST];
 static int nr_legacy_host;
 
 
-static int probe_all;		/* Set to check all ISA port ranges */
-static int ht6560a;		/* HT 6560A on primary 1, second 2, both 3 */
-static int ht6560b;		/* HT 6560A on primary 1, second 2, both 3 */
-static int opti82c611a;		/* Opti82c611A on primary 1, sec 2, both 3 */
-static int opti82c46x;		/* Opti 82c465MV present(pri/sec autodetect) */
-static int autospeed;		/* Chip present which snoops speed changes */
-static int pio_mask = ATA_PIO4;	/* PIO range for autospeed devices */
-static int iordy_mask = 0xFFFFFFFF;	/* Use iordy if available */
-
-/* Set to probe QDI controllers */
-#ifdef CONFIG_PATA_QDI_MODULE
-static int qdi = 1;
-#else
-static int qdi;
-#endif
-
-#ifdef CONFIG_PATA_WINBOND_VLB_MODULE
-static int winbond = 1;		/* Set to probe Winbond controllers,
-					give I/O port if non standard */
-#else
-static int winbond;		/* Set to probe Winbond controllers,
-					give I/O port if non standard */
-#endif
-
 /**
  *	legacy_probe_add	-	Add interface to probe list
  *	@port: Controller port
@@ -168,6 +203,8 @@ static int legacy_probe_add(unsigned long port, unsigned int irq,
 			free = lp;
 		/* Matching port, or the correct slot for ordering */
 		if (lp->port == port || legacy_port[i] == port) {
+			if (!(probe_mask & 1 << i))
+				return -1;
 			free = lp;
 			break;
 		}
@@ -588,7 +625,7 @@ static void opti82c46x_set_piomode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	opt82c465mv_qc_issue		-	command issue
+ *	opti82c46x_qc_issue		-	command issue
  *	@qc: command pending
  *
  *	Called when the libata layer is about to issue a command. We wrap
@@ -923,7 +960,7 @@ static __init int probe_chip_type(struct legacy_probe *probe)
 
 /**
  *	legacy_init_one		-	attach a legacy interface
- *	@pl: probe record
+ *	@probe: probe record
  *
  *	Register an ISA bus IDE interface. Such interfaces are PIO and we
  *	assume do not support IRQ sharing.
@@ -1009,8 +1046,8 @@ fail:
 /**
  *	legacy_check_special_cases	-	ATA special cases
  *	@p: PCI device to check
- *	@master: set this if we find an ATA master
- *	@master: set this if we find an ATA secondary
+ *	@primary: set this if we find an ATA master
+ *	@secondary: set this if we find an ATA secondary
  *
  *	A small number of vendors implemented early PCI ATA interfaces
  *	on bridge logic without the ATA interface being PCI visible.
@@ -1250,16 +1287,5 @@ MODULE_VERSION(DRV_VERSION);
 MODULE_ALIAS("pata_qdi");
 MODULE_ALIAS("pata_winbond");
 
-module_param(probe_all, int, 0);
-module_param(autospeed, int, 0);
-module_param(ht6560a, int, 0);
-module_param(ht6560b, int, 0);
-module_param(opti82c611a, int, 0);
-module_param(opti82c46x, int, 0);
-module_param(qdi, int, 0);
-module_param(winbond, int, 0);
-module_param(pio_mask, int, 0);
-module_param(iordy_mask, int, 0);
-
 module_init(legacy_init);
 module_exit(legacy_exit);
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index b066809ba9a1..361597d14c56 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -110,7 +110,7 @@ static struct ata_port_operations marvell_ops = {
 /**
  *	marvell_init_one - Register Marvell ATA PCI device with kernel services
  *	@pdev: PCI device to register
- *	@ent: Entry in marvell_pci_tbl matching with @pdev
+ *	@id: PCI device ID
  *
  *	Called from kernel PCI layer.
  *
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index 1532b2e3c672..f4949e704356 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -113,7 +113,7 @@ static void ns87415_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *	ns87415_bmdma_setup		-	Set up DMA
  *	@qc: Command block
  *
- *	Set up for bus masterng DMA. We have to do this ourselves
+ *	Set up for bus mastering DMA. We have to do this ourselves
  *	rather than use the helper due to a chip erratum
  */
 
@@ -174,7 +174,7 @@ static void ns87415_bmdma_stop(struct ata_queued_cmd *qc)
  *	ns87415_irq_clear		-	Clear interrupt
  *	@ap: Channel to clear
  *
- *	Erratum: Due to a chip bug regisers 02 and 0A bit 1 and 2 (the
+ *	Erratum: Due to a chip bug registers 02 and 0A bit 1 and 2 (the
  *	error bits) are reset by writing to register 00 or 08.
  */
 
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 06a800a3b070..01976c4e4033 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -69,7 +69,7 @@ static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
 /**
  *	opti_write_reg		-	control register setup
  *	@ap: ATA port
- *	@value: value
+ *	@val: value
  *	@reg: control register number
  *
  *	The Opti uses magic 'trapdoor' register accesses to do configuration
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index fbcf0af34924..f6278d9de348 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -287,7 +287,7 @@ static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	optidma_make_bits	-	PCI setup helper
+ *	optidma_make_bits43	-	PCI setup helper
  *	@adev: ATA device
  *
  *	Turn the ATA device setup into PCI configuration bits
@@ -309,6 +309,7 @@ static u8 optidma_make_bits43(struct ata_device *adev)
 /**
  *	optidma_set_mode	-	mode setup
  *	@link: link to set up
+ *	@r_failed: out parameter for failed device
  *
  *	Use the standard setup to tune the chipset and then finalise the
  *	configuration by writing the nibble of extra bits of data into
@@ -354,7 +355,7 @@ static struct ata_port_operations optiplus_port_ops = {
 
 /**
  *	optiplus_with_udma	-	Look for UDMA capable setup
- *	@pdev; ATA controller
+ *	@pdev: ATA controller
  */
 
 static int optiplus_with_udma(struct pci_dev *pdev)
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index de834fbb6dfe..effc1a09444d 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -196,7 +196,7 @@ static inline void __iomem *dev_mmio(struct ata_port *ap, struct ata_device *ade
 }
 
 /**
- *	pdc2027x_pata_cable_detect - Probe host controller cable detect info
+ *	pdc2027x_cable_detect - Probe host controller cable detect info
  *	@ap: Port for which cable detect info is desired
  *
  *	Read 80c cable indicator from Promise extended register.
@@ -251,7 +251,7 @@ static int pdc2027x_prereset(struct ata_link *link, unsigned long deadline)
 }
 
 /**
- *	pdc2720x_mode_filter	-	mode selection filter
+ *	pdc2027x_mode_filter	-	mode selection filter
  *	@adev: ATA device
  *	@mask: list of modes proposed
  *
@@ -503,11 +503,11 @@ retry:
 }
 
 /**
- * adjust_pll - Adjust the PLL input clock in Hz.
+ * pdc_adjust_pll - Adjust the PLL input clock in Hz.
  *
- * @pdc_controller: controller specific information
  * @host: target ATA host
  * @pll_clock: The input of PLL in HZ
+ * @board_idx: board identifier
  */
 static void pdc_adjust_pll(struct ata_host *host, long pll_clock, unsigned int board_idx)
 {
@@ -590,7 +590,7 @@ static void pdc_adjust_pll(struct ata_host *host, long pll_clock, unsigned int b
 }
 
 /**
- * detect_pll_input_clock - Detect the PLL input clock in Hz.
+ * pdc_detect_pll_input_clock - Detect the PLL input clock in Hz.
  * @host: target ATA host
  * Ex. 16949000 on 33MHz PCI bus for pdc20275.
  *     Half of the PCI clock.
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 378ed9ea97e9..0c5cbcd28d0d 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -115,7 +115,7 @@ static void pdc202xx_set_piomode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	pdc202xx_configure_dmamode	-	set DMA mode in chip
+ *	pdc202xx_set_dmamode	-	set DMA mode in chip
  *	@ap: ATA interface
  *	@adev: ATA device
  *
@@ -214,7 +214,7 @@ static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	pdc2026x_bmdma_end		-	DMA engine stop
+ *	pdc2026x_bmdma_stop		-	DMA engine stop
  *	@qc: ATA command
  *
  *	After a DMA completes we need to put the clock back to 33MHz for
diff --git a/drivers/ata/pata_piccolo.c b/drivers/ata/pata_piccolo.c
index 35cb0e263237..389b63b13c70 100644
--- a/drivers/ata/pata_piccolo.c
+++ b/drivers/ata/pata_piccolo.c
@@ -74,7 +74,7 @@ static struct ata_port_operations tosh_port_ops = {
 };
 
 /**
- *	ata_tosh_init		-	attach generic IDE
+ *	ata_tosh_init_one		-	attach generic IDE
  *	@dev: PCI device found
  *	@id: match entry
  *
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 5aba691f09af..028329428b75 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -24,6 +24,8 @@
 #define DRV_VERSION "1.2"
 
 static int pio_mask = 1;
+module_param(pio_mask, int, 0);
+MODULE_PARM_DESC(pio_mask, "PIO modes supported, mode 0 only by default");
 
 /*
  * Provide our own set_mode() as we don't want to change anything that has
@@ -233,8 +235,6 @@ static struct platform_driver pata_platform_driver = {
 
 module_platform_driver(pata_platform_driver);
 
-module_param(pio_mask, int, 0);
-
 MODULE_AUTHOR("Paul Mundt");
 MODULE_DESCRIPTION("low-level driver for platform device ATA");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 7ab9aea3b630..43215a664b96 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -57,6 +57,7 @@ static unsigned long sil680_selreg(struct ata_port *ap, int r)
 /**
  *	sil680_seldev		-	return register base
  *	@ap: ATA interface
+ *	@adev: ATA device
  *	@r: config offset
  *
  *	Turn a config register offset into the right address in PCI space
@@ -244,6 +245,7 @@ static struct ata_port_operations sil680_port_ops = {
 /**
  *	sil680_init_chip		-	chip setup
  *	@pdev: PCI device
+ *	@try_mmio: Indicates to caller whether MMIO should be attempted
  *
  *	Perform all the chip setup which must be done both when the device
  *	is powered up on boot and when we resume in case we resumed from RAM.
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index d7cd39a9888a..b5b764e18adf 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -114,7 +114,6 @@ static int sis_port_base(struct ata_device *adev)
 /**
  *	sis_133_cable_detect - check for 40/80 pin
  *	@ap: Port
- *	@deadline: deadline jiffies for the operation
  *
  *	Perform cable detection for the later UDMA133 capable
  *	SiS chipset.
@@ -521,6 +520,7 @@ static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 /**
  *	sis_133_mode_filter - mode selection filter
  *	@adev: ATA device
+ *	@mask: received mask to manipulate and pass back
  *
  *	Block UDMA6 on devices that do not support it.
  */
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index ac7ddd87f188..8487470e2e01 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -173,7 +173,7 @@ static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	sl82c105_bmdma_end		-	DMA engine stop
+ *	sl82c105_bmdma_stop		-	DMA engine stop
  *	@qc: ATA command
  *
  *	Reset the DMA engine each use as recommended by the errata
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index 2a4d38b98026..8a033598e7e1 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -129,7 +129,7 @@ static void triflex_set_piomode(struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	triflex_dma_start	-	DMA start callback
+ *	triflex_bmdma_start	-	DMA start callback
  *	@qc: Command in progress
  *
  *	Usually drivers set the DMA timing at the point the set_dmamode call
@@ -146,9 +146,8 @@ static void triflex_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	triflex_dma_stop	-	DMA stop callback
- *	@ap: ATA interface
- *	@adev: ATA device
+ *	triflex_bmdma_stop	-	DMA stop callback
+ *	@qc: ATA command
  *
  *	We loaded new timings in dma_start, as a result we need to restore
  *	the PIO timings in dma_stop so that the next command issue gets the
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 38044e679795..475032048984 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -663,7 +663,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 #ifdef CONFIG_PM_SLEEP
 /**
  *	via_reinit_one		-	reinit after resume
- *	@pdev; PCI device
+ *	@pdev: PCI device
  *
  *	Called when the VIA PATA device is resumed. We must then
  *	reconfigure the fifo and other setup we may have altered. In
diff --git a/drivers/ata/sata_dwc_460ex.c b/drivers/ata/sata_dwc_460ex.c
index 9dcef6ac643b..f0ef844428bb 100644
--- a/drivers/ata/sata_dwc_460ex.c
+++ b/drivers/ata/sata_dwc_460ex.c
@@ -543,6 +543,11 @@ static irqreturn_t sata_dwc_isr(int irq, void *dev_instance)
 		hsdev->sactive_issued |= qcmd_tag_to_mask(tag);
 
 		qc = ata_qc_from_tag(ap, tag);
+		if (unlikely(!qc)) {
+			dev_err(ap->dev, "failed to get qc");
+			handled = 1;
+			goto DONE;
+		}
 		/*
 		 * Start FP DMA for NCQ command.  At this point the tag is the
 		 * active tag.  It is the tag that matches the command about to
@@ -658,6 +663,11 @@ DRVSTILLBUSY:
 
 		tag_mask &= (~0x00000001);
 		qc = ata_qc_from_tag(ap, tag);
+		if (unlikely(!qc)) {
+			dev_err(ap->dev, "failed to get qc");
+			handled = 1;
+			goto DONE;
+		}
 
 		/* To be picked up by completion functions */
 		qc->ap->link.active_tag = tag;
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 664ef658a955..c8867c12c0b8 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -1146,9 +1146,8 @@ static void mv_set_irq_coalescing(struct ata_host *host,
 	spin_unlock_irqrestore(&host->lock, flags);
 }
 
-/**
+/*
  *      mv_start_edma - Enable eDMA engine
- *      @base: port base address
  *      @pp: port private data
  *
  *      Verify the local cache of the eDMA state is accurate with a
@@ -1519,7 +1518,7 @@ static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
 		writel(new, hpriv->base + GPIO_PORT_CTL);
 }
 
-/**
+/*
  *	mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma
  *	@ap: Port being initialized
  *
@@ -1918,8 +1917,8 @@ static void mv_bmdma_start(struct ata_queued_cmd *qc)
 }
 
 /**
- *	mv_bmdma_stop - Stop BMDMA transfer
- *	@qc: queued command to stop DMA on.
+ *	mv_bmdma_stop_ap - Stop BMDMA transfer
+ *	@ap: port to stop
  *
  *	Clears the ATA_DMA_START flag in the bmdma control register
  *
@@ -2221,6 +2220,7 @@ static u8 mv_sff_check_status(struct ata_port *ap)
 
 /**
  *	mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register
+ *	@ap: ATA port to send a FIS
  *	@fis: fis to be sent
  *	@nwords: number of 32-bit words in the fis
  */
@@ -3249,7 +3249,7 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
 	writel(tmp, mmio + GPIO_PORT_CTL);
 }
 
-/**
+/*
  *      mv6_reset_hc - Perform the 6xxx global soft reset
  *      @mmio: base address of the HBA
  *
@@ -3530,7 +3530,7 @@ static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv,
 	writel(reg, port_mmio + PHY_MODE9_GEN1);
 }
 
-/**
+/*
  *	soc_is_65 - check if the soc is 65 nano device
  *
  *	Detect the type of the SoC, this is done by reading the PHYCFG_OFS
@@ -4097,6 +4097,10 @@ static int mv_platform_probe(struct platform_device *pdev)
 		n_ports = mv_platform_data->n_ports;
 		irq = platform_get_irq(pdev, 0);
 	}
+	if (irq < 0)
+		return irq;
+	if (!irq)
+		return -EINVAL;
 
 	host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
 	hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);