Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block

Pull block updates from Jens Axboe:

 - Two NVMe pull requests:
     - ana log parse fix from Anton
     - nvme quirks support for Apple devices from Ben
     - fix missing bio completion tracing for multipath stack devices
       from Hannes and Mikhail
     - IP TOS settings for nvme rdma and tcp transports from Israel
     - rq_dma_dir cleanups from Israel
     - tracing for Get LBA Status command from Minwoo
     - Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
     - Some consolidation between the fabrics transports for handling
       the CAP register
     - reset race with ns scanning fix for fabrics (move fabrics
       commands to a dedicated request queue with a different lifetime
       from the admin request queue)."
     - controller reset and namespace scan races fixes
     - nvme discovery log change uevent support
     - naming improvements from Keith
     - multiple discovery controllers reject fix from James
     - some regular cleanups from various people

 - Series fixing (and re-fixing) null_blk debug printing and nr_devices
   checks (André)

 - A few pull requests from Song, with fixes from Andy, Guoqing,
   Guilherme, Neil, Nigel, and Yufen.

 - REQ_OP_ZONE_RESET_ALL support (Chaitanya)

 - Bio merge handling unification (Christoph)

 - Pick default elevator correctly for devices with special needs
   (Damien)

 - Block stats fixes (Hou)

 - Timeout and support devices nbd fixes (Mike)

 - Series fixing races around elevator switching and device add/remove
   (Ming)

 - sed-opal cleanups (Revanth)

 - Per device weight support for BFQ (Fam)

 - Support for blk-iocost, a new model that can properly account cost of
   IO workloads. (Tejun)

 - blk-cgroup writeback fixes (Tejun)

 - paride queue init fixes (zhengbin)

 - blk_set_runtime_active() cleanup (Stanley)

 - Block segment mapping optimizations (Bart)

 - lightnvm fixes (Hans/Minwoo/YueHaibing)

 - Various little fixes and cleanups

* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
  null_blk: format pr_* logs with pr_fmt
  null_blk: match the type of parameter nr_devices
  null_blk: do not fail the module load with zero devices
  block: also check RQF_STATS in blk_mq_need_time_stamp()
  block: make rq sector size accessible for block stats
  bfq: Fix bfq linkage error
  raid5: use bio_end_sector in r5_next_bio
  raid5: remove STRIPE_OPS_REQ_PENDING
  md: add feature flag MD_FEATURE_RAID0_LAYOUT
  md/raid0: avoid RAID0 data corruption due to layout confusion.
  raid5: don't set STRIPE_HANDLE to stripe which is in batch list
  raid5: don't increment read_errors on EILSEQ return
  nvmet: fix a wrong error status returned in error log page
  nvme: send discovery log page change events to userspace
  nvme: add uevent variables for controller devices
  nvme: enable aen regardless of the presence of I/O queues
  nvme-fabrics: allow discovery subsystems accept a kato
  nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
  nvme: Remove redundant assignment of cq vector
  nvme: Assign subsys instance from first ctrl
  ...

3 files changed, 100 insertions, 11 deletions

diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst
index 5f1c266131b0..0fa8c0e615c2 100644
--- a/Documentation/admin-guide/cgroup-v2.rst
+++ b/Documentation/admin-guide/cgroup-v2.rst
@@ -1469,6 +1469,103 @@ IO Interface Files
 	  8:16 rbytes=1459200 wbytes=314773504 rios=192 wios=353 dbytes=0 dios=0
 	  8:0 rbytes=90430464 wbytes=299008000 rios=8950 wios=1252 dbytes=50331648 dios=3021
 
+  io.cost.qos
+	A read-write nested-keyed file with exists only on the root
+	cgroup.
+
+	This file configures the Quality of Service of the IO cost
+	model based controller (CONFIG_BLK_CGROUP_IOCOST) which
+	currently implements "io.weight" proportional control.  Lines
+	are keyed by $MAJ:$MIN device numbers and not ordered.  The
+	line for a given device is populated on the first write for
+	the device on "io.cost.qos" or "io.cost.model".  The following
+	nested keys are defined.
+
+	  ======	=====================================
+	  enable	Weight-based control enable
+	  ctrl		"auto" or "user"
+	  rpct		Read latency percentile    [0, 100]
+	  rlat		Read latency threshold
+	  wpct		Write latency percentile   [0, 100]
+	  wlat		Write latency threshold
+	  min		Minimum scaling percentage [1, 10000]
+	  max		Maximum scaling percentage [1, 10000]
+	  ======	=====================================
+
+	The controller is disabled by default and can be enabled by
+	setting "enable" to 1.  "rpct" and "wpct" parameters default
+	to zero and the controller uses internal device saturation
+	state to adjust the overall IO rate between "min" and "max".
+
+	When a better control quality is needed, latency QoS
+	parameters can be configured.  For example::
+
+	  8:16 enable=1 ctrl=auto rpct=95.00 rlat=75000 wpct=95.00 wlat=150000 min=50.00 max=150.0
+
+	shows that on sdb, the controller is enabled, will consider
+	the device saturated if the 95th percentile of read completion
+	latencies is above 75ms or write 150ms, and adjust the overall
+	IO issue rate between 50% and 150% accordingly.
+
+	The lower the saturation point, the better the latency QoS at
+	the cost of aggregate bandwidth.  The narrower the allowed
+	adjustment range between "min" and "max", the more conformant
+	to the cost model the IO behavior.  Note that the IO issue
+	base rate may be far off from 100% and setting "min" and "max"
+	blindly can lead to a significant loss of device capacity or
+	control quality.  "min" and "max" are useful for regulating
+	devices which show wide temporary behavior changes - e.g. a
+	ssd which accepts writes at the line speed for a while and
+	then completely stalls for multiple seconds.
+
+	When "ctrl" is "auto", the parameters are controlled by the
+	kernel and may change automatically.  Setting "ctrl" to "user"
+	or setting any of the percentile and latency parameters puts
+	it into "user" mode and disables the automatic changes.  The
+	automatic mode can be restored by setting "ctrl" to "auto".
+
+  io.cost.model
+	A read-write nested-keyed file with exists only on the root
+	cgroup.
+
+	This file configures the cost model of the IO cost model based
+	controller (CONFIG_BLK_CGROUP_IOCOST) which currently
+	implements "io.weight" proportional control.  Lines are keyed
+	by $MAJ:$MIN device numbers and not ordered.  The line for a
+	given device is populated on the first write for the device on
+	"io.cost.qos" or "io.cost.model".  The following nested keys
+	are defined.
+
+	  =====		================================
+	  ctrl		"auto" or "user"
+	  model		The cost model in use - "linear"
+	  =====		================================
+
+	When "ctrl" is "auto", the kernel may change all parameters
+	dynamically.  When "ctrl" is set to "user" or any other
+	parameters are written to, "ctrl" become "user" and the
+	automatic changes are disabled.
+
+	When "model" is "linear", the following model parameters are
+	defined.
+
+	  =============	========================================
+	  [r|w]bps	The maximum sequential IO throughput
+	  [r|w]seqiops	The maximum 4k sequential IOs per second
+	  [r|w]randiops	The maximum 4k random IOs per second
+	  =============	========================================
+
+	From the above, the builtin linear model determines the base
+	costs of a sequential and random IO and the cost coefficient
+	for the IO size.  While simple, this model can cover most
+	common device classes acceptably.
+
+	The IO cost model isn't expected to be accurate in absolute
+	sense and is scaled to the device behavior dynamically.
+
+	If needed, tools/cgroup/iocost_coef_gen.py can be used to
+	generate device-specific coefficients.
+
   io.weight
 	A read-write flat-keyed file which exists on non-root cgroups.
 	The default is "default 100".
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 3e2d22eb5e59..6ef205fd7c97 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1201,12 +1201,6 @@
 			See comment before function elanfreq_setup() in
 			arch/x86/kernel/cpu/cpufreq/elanfreq.c.
 
-	elevator=	[IOSCHED]
-			Format: { "mq-deadline" | "kyber" | "bfq" }
-			See Documentation/block/deadline-iosched.rst,
-			Documentation/block/kyber-iosched.rst and
-			Documentation/block/bfq-iosched.rst for details.
-
 	elfcorehdr=[size[KMG]@]offset[KMG] [IA64,PPC,SH,X86,S390]
 			Specifies physical address of start of kernel core
 			image elf header and optionally the size. Generally
diff --git a/Documentation/admin-guide/kernel-per-CPU-kthreads.rst b/Documentation/admin-guide/kernel-per-CPU-kthreads.rst
index 4f18456dd3b1..baeeba8762ae 100644
--- a/Documentation/admin-guide/kernel-per-CPU-kthreads.rst
+++ b/Documentation/admin-guide/kernel-per-CPU-kthreads.rst
@@ -274,9 +274,7 @@ To reduce its OS jitter, do any of the following:
 		(based on an earlier one from Gilad Ben-Yossef) that
 		reduces or even eliminates vmstat overhead for some
 		workloads at https://lkml.org/lkml/2013/9/4/379.
-	e.	Boot with "elevator=noop" to avoid workqueue use by
-		the block layer.
-	f.	If running on high-end powerpc servers, build with
+	e.	If running on high-end powerpc servers, build with
 		CONFIG_PPC_RTAS_DAEMON=n.  This prevents the RTAS
 		daemon from running on each CPU every second or so.
 		(This will require editing Kconfig files and will defeat
@@ -284,12 +282,12 @@ To reduce its OS jitter, do any of the following:
 		due to the rtas_event_scan() function.
 		WARNING:  Please check your CPU specifications to
 		make sure that this is safe on your particular system.
-	g.	If running on Cell Processor, build your kernel with
+	f.	If running on Cell Processor, build your kernel with
 		CBE_CPUFREQ_SPU_GOVERNOR=n to avoid OS jitter from
 		spu_gov_work().
 		WARNING:  Please check your CPU specifications to
 		make sure that this is safe on your particular system.
-	h.	If running on PowerMAC, build your kernel with
+	g.	If running on PowerMAC, build your kernel with
 		CONFIG_PMAC_RACKMETER=n to disable the CPU-meter,
 		avoiding OS jitter from rackmeter_do_timer().