dt-bindings: intel,ixp4xx-expansion-bus: split out peripheral properties

The properties of devices in IXP4xx expansion bus need to be also
applied to actual devices' bindings.  Prepare for this by splitting them
to separate intel,ixp4xx-expansion-peripheral-props binding, just like
other memory-controller peripheral properties.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230206092624.22922-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 0 insertions, 168 deletions

diff --git a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
deleted file mode 100644
index 5fb4e7bfa4da..000000000000
--- a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
+++ /dev/null
@@ -1,168 +0,0 @@
-# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/bus/intel,ixp4xx-expansion-bus-controller.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Intel IXP4xx Expansion Bus Controller
-
-description: |
-  The IXP4xx expansion bus controller handles access to devices on the
-  memory-mapped expansion bus on the Intel IXP4xx family of system on chips,
-  including IXP42x, IXP43x, IXP45x and IXP46x.
-
-maintainers:
-  - Linus Walleij <linus.walleij@linaro.org>
-
-properties:
-  $nodename:
-    pattern: '^bus@[0-9a-f]+$'
-
-  compatible:
-    items:
-      - enum:
-          - intel,ixp42x-expansion-bus-controller
-          - intel,ixp43x-expansion-bus-controller
-          - intel,ixp45x-expansion-bus-controller
-          - intel,ixp46x-expansion-bus-controller
-      - const: syscon
-
-  reg:
-    description: Control registers for the expansion bus, these are not
-      inside the memory range handled by the expansion bus.
-    maxItems: 1
-
-  native-endian:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description: The IXP4xx has a peculiar MMIO access scheme, as it changes
-      the access pattern for words (swizzling) on the bus depending on whether
-      the SoC is running in big-endian or little-endian mode. Thus the
-      registers must always be accessed using native endianness.
-
-  "#address-cells":
-    description: |
-      The first cell is the chip select number.
-      The second cell is the address offset within the bank.
-    const: 2
-
-  "#size-cells":
-    const: 1
-
-  ranges: true
-  dma-ranges: true
-
-patternProperties:
-  "^.*@[0-7],[0-9a-f]+$":
-    description: Devices attached to chip selects are represented as
-      subnodes.
-    type: object
-
-    properties:
-      intel,ixp4xx-eb-t1:
-        description: Address timing, extend address phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t2:
-        description: Setup chip select timing, extend setup phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t3:
-        description: Strobe timing, extend strobe phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 15
-
-      intel,ixp4xx-eb-t4:
-        description: Hold timing, extend hold phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t5:
-        description: Recovery timing, extend recovery phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 15
-
-      intel,ixp4xx-eb-cycle-type:
-        description: The type of cycles to use on the expansion bus for this
-          chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1, 2]
-
-      intel,ixp4xx-eb-byte-access-on-halfword:
-        description: Allow byte read access on half word devices.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-hpi-hrdy-pol-high:
-        description: Set HPI HRDY polarity to active high when using HPI.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-mux-address-and-data:
-        description: Multiplex address and data on the data bus.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-ahb-split-transfers:
-        description: Enable AHB split transfers.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-write-enable:
-        description: Enable write cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-byte-access:
-        description: Expansion bus uses only 8 bits. The default is to use
-          16 bits.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-required:
-  - compatible
-  - reg
-  - native-endian
-  - "#address-cells"
-  - "#size-cells"
-  - ranges
-  - dma-ranges
-
-additionalProperties: false
-
-examples:
-  - |
-    #include <dt-bindings/interrupt-controller/irq.h>
-    bus@50000000 {
-        compatible = "intel,ixp42x-expansion-bus-controller", "syscon";
-        reg = <0xc4000000 0x28>;
-        native-endian;
-        #address-cells = <2>;
-        #size-cells = <1>;
-        ranges = <0 0x0 0x50000000 0x01000000>,
-                 <1 0x0 0x51000000 0x01000000>;
-        dma-ranges = <0 0x0 0x50000000 0x01000000>,
-                     <1 0x0 0x51000000 0x01000000>;
-        flash@0,0 {
-            compatible = "intel,ixp4xx-flash", "cfi-flash";
-            bank-width = <2>;
-            reg = <0 0x00000000 0x1000000>;
-            intel,ixp4xx-eb-t3 = <3>;
-            intel,ixp4xx-eb-cycle-type = <0>;
-            intel,ixp4xx-eb-byte-access-on-halfword = <1>;
-            intel,ixp4xx-eb-write-enable = <1>;
-            intel,ixp4xx-eb-byte-access = <0>;
-        };
-        serial@1,0 {
-            compatible = "exar,xr16l2551", "ns8250";
-            reg = <1 0x00000000 0x10>;
-            interrupt-parent = <&gpio0>;
-            interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
-            clock-frequency = <1843200>;
-            intel,ixp4xx-eb-t3 = <3>;
-            intel,ixp4xx-eb-cycle-type = <1>;
-            intel,ixp4xx-eb-write-enable = <1>;
-            intel,ixp4xx-eb-byte-access = <1>;
-        };
-    };