Merge tag 'v3.11' into next

Merge with mainline to bring in sync changes to cyttsp4 driver.

2 files changed, 49 insertions, 19 deletions

diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt
index ce3e394c0e64..942d071baaa5 100644
--- a/Documentation/devicetree/bindings/input/samsung-keypad.txt
+++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt
@@ -25,14 +25,6 @@ Required Board Specific Properties:
 - samsung,keypad-num-columns: Number of column lines connected to the
   keypad controller.
 
-- row-gpios: List of gpios used as row lines. The gpio specifier for
-  this property depends on the gpio controller to which these row lines
-  are connected.
-
-- col-gpios: List of gpios used as column lines. The gpio specifier for
-  this property depends on the gpio controller to which these column
-  lines are connected.
-
 - Keys represented as child nodes: Each key connected to the keypad
   controller is represented as a child node to the keypad controller
   device node and should include the following properties.
@@ -41,6 +33,9 @@ Required Board Specific Properties:
   - linux,code: the key-code to be reported when the key is pressed
     and released.
 
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
+
 Optional Properties specific to linux:
 - linux,keypad-no-autorepeat: do no enable autorepeat feature.
 - linux,keypad-wakeup: use any event on keypad as wakeup event.
@@ -56,17 +51,8 @@ Example:
 		linux,input-no-autorepeat;
 		linux,input-wakeup;
 
-		row-gpios = <&gpx2 0 3 3 0
-			     &gpx2 1 3 3 0>;
-
-		col-gpios = <&gpx1 0 3 0 0
-			     &gpx1 1 3 0 0
-			     &gpx1 2 3 0 0
-			     &gpx1 3 3 0 0
-			     &gpx1 4 3 0 0
-			     &gpx1 5 3 0 0
-			     &gpx1 6 3 0 0
-			     &gpx1 7 3 0 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&keypad_rows &keypad_columns>;
 
 		key_1 {
 			keypad,row = <0>;
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
new file mode 100644
index 000000000000..491c97b78384
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
@@ -0,0 +1,44 @@
+* TI - TSC ADC (Touschscreen and analog digital converter)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties:
+- child "tsc"
+	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
+		  support on the platform.
+	ti,x-plate-resistance: X plate resistance
+	ti,coordiante-readouts: The sequencer supports a total of 16
+				programmable steps each step is used to
+				read a single coordinate. A single
+                                readout is enough but multiple reads can
+				increase the quality.
+				A value of 5 means, 5 reads for X, 5 for
+				Y and 2 for Z (always). This utilises 12
+				of the 16 software steps available. The
+				remaining 4 can be used by the ADC.
+	ti,wire-config: Different boards could have a different order for
+			connecting wires on touchscreen. We need to provide an
+			8 bit number where in the 1st four bits represent the
+			analog lines and the next 4 bits represent positive/
+			negative terminal on that input line. Notations to
+			represent the input lines and terminals resoectively
+			is as follows:
+			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+			XP  = 0, XN = 1, YP = 2, YN = 3.
+- child "adc"
+	ti,adc-channels: List of analog inputs available for ADC.
+			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+
+Example:
+	tscadc: tscadc@44e0d000 {
+		compatible = "ti,am3359-tscadc";
+		tsc {
+			ti,wires = <4>;
+			ti,x-plate-resistance = <200>;
+			ti,coordiante-readouts = <5>;
+			ti,wire-config = <0x00 0x11 0x22 0x33>;
+		};
+
+		adc {
+			ti,adc-channels = <4 5 6 7>;
+		};
+	}