diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2018-06-08 19:39:20 +0200 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2018-06-08 19:39:20 +0200 |
commit | f4e70c2e5f1406e715f6359ae341e76e5004fb98 (patch) | |
tree | 79622d866d0cb8bdb494718e11d458770aee9713 /Documentation/devicetree/bindings/mtd/mtk-nand.txt | |
parent | Merge tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lin... (diff) | |
parent | Merge tag 'spi-nor/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next (diff) | |
download | linux-f4e70c2e5f1406e715f6359ae341e76e5004fb98.tar.xz linux-f4e70c2e5f1406e715f6359ae341e76e5004fb98.zip |
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/mtk-nand.txt')
-rw-r--r-- | Documentation/devicetree/bindings/mtd/mtk-nand.txt | 24 |
1 files changed, 19 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt index c5ba6a4ba1f2..4d3ec5e4ff8a 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -48,14 +48,19 @@ Optional: - nand-on-flash-bbt: Store BBT on NAND Flash. - nand-ecc-mode: the NAND ecc mode (check driver for supported modes) - nand-ecc-step-size: Number of data bytes covered by a single ECC step. - valid values: 512 and 1024. + valid values: + 512 and 1024 on mt2701 and mt2712. + 512 only on mt7622. 1024 is recommended for large page NANDs. - nand-ecc-strength: Number of bits to correct per ECC step. - The valid values that the controller supports are: 4, 6, - 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44, - 48, 52, 56, 60. + The valid values that each controller supports: + mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, + 32, 36, 40, 44, 48, 52, 56, 60. + mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, + 32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80. + mt7622: 4, 6, 8, 10, 12, 14, 16. The strength should be calculated as follows: - E = (S - F) * 8 / 14 + E = (S - F) * 8 / B S = O / (P / Q) E : nand-ecc-strength. S : spare size per sector. @@ -64,6 +69,15 @@ Optional: O : oob size. P : page size. Q : nand-ecc-step-size. + B : number of parity bits needed to correct + 1 bitflip. + According to MTK NAND controller design, + this number depends on max ecc step size + that MTK NAND controller supports. + If max ecc step size supported is 1024, + then it should be always 14. And if max + ecc step size is 512, then it should be + always 13. If the result does not match any one of the listed choices above, please select the smaller valid value from the list. |