nfs: disintegrate UAPI for nfs

This is to complete part of the Userspace API (UAPI) disintegration for which
the preparatory patches were pulled recently.  After these patches, userspace
headers will be segregated into:

        include/uapi/linux/.../foo.h

for the userspace interface stuff, and:

        include/linux/.../foo.h

for the strictly kernel internal stuff.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>

5 files changed, 269 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
index 411727a3f82d..c8ae996bd8f2 100644
--- a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
+++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt
@@ -6,6 +6,9 @@ Required properties:
 - interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
   The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
 
+Optional properties:
+- dma-coherent      : Present if dma operations are coherent
+
 Example:
 
 ethernet@fff50000 {
diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt
new file mode 100644
index 000000000000..8f1ae81228e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/c_can.txt
@@ -0,0 +1,49 @@
+Bosch C_CAN/D_CAN controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible		: Should be "bosch,c_can" for C_CAN controllers and
+			  "bosch,d_can" for D_CAN controllers.
+- reg			: physical base address and size of the C_CAN/D_CAN
+			  registers map
+- interrupts		: property with a value describing the interrupt
+			  number
+
+Optional properties:
+- ti,hwmods		: Must be "d_can<n>" or "c_can<n>", n being the
+			  instance number
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Example:
+
+Step1: SoC common .dtsi file
+
+	dcan1: d_can@481d0000 {
+		compatible = "bosch,d_can";
+		reg = <0x481d0000 0x2000>;
+		interrupts = <55>;
+		interrupt-parent = <&intc>;
+		status = "disabled";
+	};
+
+(or)
+
+	dcan1: d_can@481d0000 {
+		compatible = "bosch,d_can";
+		ti,hwmods = "d_can1";
+		reg = <0x481d0000 0x2000>;
+		interrupts = <55>;
+		interrupt-parent = <&intc>;
+		status = "disabled";
+	};
+
+Step 2: board specific .dts file
+
+	&dcan1 {
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
new file mode 100644
index 000000000000..dcaabe9fe869
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -0,0 +1,109 @@
+TI SoC Ethernet Switch Controller Device Tree Bindings
+------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "ti,cpsw"
+- reg			: physical base address and size of the cpsw
+			  registers map
+- interrupts		: property with a value describing the interrupt
+			  number
+- interrupt-parent	: The parent interrupt controller
+- cpdma_channels 	: Specifies number of channels in CPDMA
+- host_port_no		: Specifies host port shift
+- cpdma_reg_ofs		: Specifies CPDMA submodule register offset
+- cpdma_sram_ofs	: Specifies CPDMA SRAM offset
+- ale_reg_ofs		: Specifies ALE submodule register offset
+- ale_entries		: Specifies No of entries ALE can hold
+- host_port_reg_ofs	: Specifies host port register offset
+- hw_stats_reg_ofs	: Specifies hardware statistics register offset
+- bd_ram_ofs		: Specifies internal desciptor RAM offset
+- bd_ram_size		: Specifies internal descriptor RAM size
+- rx_descs		: Specifies number of Rx descriptors
+- mac_control		: Specifies Default MAC control register content
+			  for the specific platform
+- slaves		: Specifies number for slaves
+- slave_reg_ofs		: Specifies slave register offset
+- sliver_reg_ofs	: Specifies slave sliver register offset
+- phy_id		: Specifies slave phy id
+- mac-address		: Specifies slave MAC address
+
+Optional properties:
+- ti,hwmods		: Must be "cpgmac0"
+- no_bd_ram		: Must be 0 or 1
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples:
+
+	mac: ethernet@4A100000 {
+		compatible = "ti,cpsw";
+		reg = <0x4A100000 0x1000>;
+		interrupts = <55 0x4>;
+		interrupt-parent = <&intc>;
+		cpdma_channels = <8>;
+		host_port_no = <0>;
+		cpdma_reg_ofs = <0x800>;
+		cpdma_sram_ofs = <0xa00>;
+		ale_reg_ofs = <0xd00>;
+		ale_entries = <1024>;
+		host_port_reg_ofs = <0x108>;
+		hw_stats_reg_ofs = <0x900>;
+		bd_ram_ofs = <0x2000>;
+		bd_ram_size = <0x2000>;
+		no_bd_ram = <0>;
+		rx_descs = <64>;
+		mac_control = <0x20>;
+		slaves = <2>;
+		cpsw_emac0: slave@0 {
+			slave_reg_ofs = <0x208>;
+			sliver_reg_ofs = <0xd80>;
+			phy_id = "davinci_mdio.16:00";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+		};
+		cpsw_emac1: slave@1 {
+			slave_reg_ofs = <0x308>;
+			sliver_reg_ofs = <0xdc0>;
+			phy_id = "davinci_mdio.16:01";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
+
+(or)
+	mac: ethernet@4A100000 {
+		compatible = "ti,cpsw";
+		ti,hwmods = "cpgmac0";
+		cpdma_channels = <8>;
+		host_port_no = <0>;
+		cpdma_reg_ofs = <0x800>;
+		cpdma_sram_ofs = <0xa00>;
+		ale_reg_ofs = <0xd00>;
+		ale_entries = <1024>;
+		host_port_reg_ofs = <0x108>;
+		hw_stats_reg_ofs = <0x900>;
+		bd_ram_ofs = <0x2000>;
+		bd_ram_size = <0x2000>;
+		no_bd_ram = <0>;
+		rx_descs = <64>;
+		mac_control = <0x20>;
+		slaves = <2>;
+		cpsw_emac0: slave@0 {
+			slave_reg_ofs = <0x208>;
+			sliver_reg_ofs = <0xd80>;
+			phy_id = "davinci_mdio.16:00";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+		};
+		cpsw_emac1: slave@1 {
+			slave_reg_ofs = <0x308>;
+			sliver_reg_ofs = <0xdc0>;
+			phy_id = "davinci_mdio.16:01";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
new file mode 100644
index 000000000000..72efaaf764f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -0,0 +1,33 @@
+TI SoC Davinci MDIO Controller Device Tree Bindings
+---------------------------------------------------
+
+Required properties:
+- compatible		: Should be "ti,davinci_mdio"
+- reg			: physical base address and size of the davinci mdio
+			  registers map
+- bus_freq		: Mdio Bus frequency
+
+Optional properties:
+- ti,hwmods		: Must be "davinci_mdio"
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples:
+
+	mdio: davinci_mdio@4A101000 {
+		compatible = "ti,cpsw";
+		reg = <0x4A101000 0x1000>;
+		bus_freq = <1000000>;
+	};
+
+(or)
+
+	mdio: davinci_mdio@4A101000 {
+		compatible = "ti,cpsw";
+		ti,hwmods = "davinci_mdio";
+		bus_freq = <1000000>;
+	};
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
new file mode 100644
index 000000000000..8516929c7251
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
@@ -0,0 +1,75 @@
+Properties for an MDIO bus multiplexer controlled by a memory-mapped device
+
+This is a special case of a MDIO bus multiplexer.  A memory-mapped device,
+like an FPGA, is used to control which child bus is connected.  The mdio-mux
+node must be a child of the memory-mapped device.  The driver currently only
+supports devices with eight-bit registers.
+
+Required properties in addition to the generic multiplexer properties:
+
+- compatible : string, must contain "mdio-mux-mmioreg"
+
+- reg : integer, contains the offset of the register that controls the bus
+	multiplexer.  The size field in the 'reg' property is the size of
+	register, and must therefore be 1.
+
+- mux-mask : integer, contains an eight-bit mask that specifies which
+	bits in the register control the actual bus multiplexer.  The
+	'reg' property of each child mdio-mux node must be constrained by
+	this mask.
+
+Example:
+
+The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes.
+For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus.
+A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on
+BRDCFG1 that control the actual mux.
+
+	/* The FPGA node */
+	fpga: board-control@3,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis";
+		reg = <3 0 0x30>;
+		ranges = <0 3 0 0x30>;
+
+		mdio-mux-emi2 {
+			compatible = "mdio-mux-mmioreg", "mdio-mux";
+			mdio-parent-bus = <&xmdio0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <9 1>; // BRDCFG1
+			mux-mask = <0x6>; // EMI2
+
+			emi2_slot1: mdio@0 {	// Slot 1 XAUI (FM2)
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_xgmii_slot1: ethernet-phy@0 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <4>;
+				};
+			};
+
+			emi2_slot2: mdio@2 {	// Slot 2 XAUI (FM1)
+				reg = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_xgmii_slot2: ethernet-phy@4 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0>;
+				};
+			};
+		};
+	};
+
+	/* The parent MDIO bus. */
+	xmdio0: mdio@f1000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,fman-xmdio";
+		reg = <0xf1000 0x1000>;
+		interrupts = <100 1 0 0>;
+	};