Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Support ipv6 checksum offload in sunvnet driver, from Shannon
    Nelson.

 2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
    Dumazet.

 3) Allow generic XDP to work on virtual devices, from John Fastabend.

 4) Add bpf device maps and XDP_REDIRECT, which can be used to build
    arbitrary switching frameworks using XDP. From John Fastabend.

 5) Remove UFO offloads from the tree, gave us little other than bugs.

 6) Remove the IPSEC flow cache, from Florian Westphal.

 7) Support ipv6 route offload in mlxsw driver.

 8) Support VF representors in bnxt_en, from Sathya Perla.

 9) Add support for forward error correction modes to ethtool, from
    Vidya Sagar Ravipati.

10) Add time filter for packet scheduler action dumping, from Jamal Hadi
    Salim.

11) Extend the zerocopy sendmsg() used by virtio and tap to regular
    sockets via MSG_ZEROCOPY. From Willem de Bruijn.

12) Significantly rework value tracking in the BPF verifier, from Edward
    Cree.

13) Add new jump instructions to eBPF, from Daniel Borkmann.

14) Rework rtnetlink plumbing so that operations can be run without
    taking the RTNL semaphore. From Florian Westphal.

15) Support XDP in tap driver, from Jason Wang.

16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.

17) Add Huawei hinic ethernet driver.

18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
    Delalande.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
  i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
  i40e: avoid NVM acquire deadlock during NVM update
  drivers: net: xgene: Remove return statement from void function
  drivers: net: xgene: Configure tx/rx delay for ACPI
  drivers: net: xgene: Read tx/rx delay for ACPI
  rocker: fix kcalloc parameter order
  rds: Fix non-atomic operation on shared flag variable
  net: sched: don't use GFP_KERNEL under spin lock
  vhost_net: correctly check tx avail during rx busy polling
  net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
  rxrpc: Make service connection lookup always check for retry
  net: stmmac: Delete dead code for MDIO registration
  gianfar: Fix Tx flow control deactivation
  cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
  cxgb4: Fix pause frame count in t4_get_port_stats
  cxgb4: fix memory leak
  tun: rename generic_xdp to skb_xdp
  tun: reserve extra headroom only when XDP is set
  net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
  net: dsa: bcm_sf2: Advertise number of egress queues
  ...

8 files changed, 174 insertions, 18 deletions

diff --git a/Documentation/devicetree/bindings/net/anarion-gmac.txt b/Documentation/devicetree/bindings/net/anarion-gmac.txt
new file mode 100644
index 000000000000..fe678965ae69
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/anarion-gmac.txt
@@ -0,0 +1,25 @@
+*  Adaptrum Anarion ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+ - compatible:  Should be "adaptrum,anarion-gmac", "snps,dwmac"
+ - phy-mode:    Should be "rgmii". Other modes are not currently supported.
+
+
+Examples:
+
+	gmac1: ethernet@f2014000 {
+		compatible = "adaptrum,anarion-gmac", "snps,dwmac";
+		reg = <0xf2014000 0x4000>, <0xf2018100 8>;
+
+		interrupt-parent = <&core_intc>;
+		interrupts = <21>;
+		interrupt-names = "macirq";
+
+		clocks = <&core_clk>;
+		clock-names = "stmmaceth";
+
+		phy-mode = "rgmii";
+	};
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
new file mode 100644
index 000000000000..4194ff7e6ee6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
@@ -0,0 +1,35 @@
+Broadcom Bluetooth Chips
+---------------------
+
+This documents the binding structure and common properties for serial
+attached Broadcom devices.
+
+Serial attached Broadcom devices shall be a child node of the host UART
+device the slave device is attached to.
+
+Required properties:
+
+ - compatible: should contain one of the following:
+   * "brcm,bcm43438-bt"
+
+Optional properties:
+
+ - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
+ - shutdown-gpios: GPIO specifier, used to enable the BT module
+ - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
+ - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor
+ - clocks: clock specifier if external clock provided to the controller
+ - clock-names: should be "extclk"
+
+
+Example:
+
+&uart2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart2_pins>;
+
+       bluetooth {
+               compatible = "brcm,bcm43438-bt";
+               max-speed = <921600>;
+       };
+};
diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index 6b4956beff8c..c78f3187dfea 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -41,6 +41,11 @@ Optional properties (port):
 - marvell,loopback: port is loopback mode
 - phy: a phandle to a phy node defining the PHY address (as the reg
   property, a single integer).
+- interrupt-names: if more than a single interrupt for rx is given, must
+                   be the name associated to the interrupts listed. Valid
+                   names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3",
+		   "rx-shared", "link".
+- marvell,system-controller: a phandle to the system controller.
 
 Example for marvell,armada-375-pp2:
 
@@ -80,19 +85,37 @@ cpm_ethernet: ethernet@0 {
 	clock-names = "pp_clk", "gop_clk", "gp_clk";
 
 	eth0: eth0 {
-		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+				  "tx-cpu3", "rx-shared";
 		port-id = <0>;
 		gop-port-id = <0>;
 	};
 
 	eth1: eth1 {
-		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+				  "tx-cpu3", "rx-shared";
 		port-id = <1>;
 		gop-port-id = <2>;
 	};
 
 	eth2: eth2 {
-		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+				  "tx-cpu3", "rx-shared";
 		port-id = <2>;
 		gop-port-id = <3>;
 	};
diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt
index c7194e87d5f4..1d1168b805cc 100644
--- a/Documentation/devicetree/bindings/net/mediatek-net.txt
+++ b/Documentation/devicetree/bindings/net/mediatek-net.txt
@@ -7,24 +7,30 @@ have dual GMAC each represented by a child node..
 * Ethernet controller node
 
 Required properties:
-- compatible: Should be "mediatek,mt2701-eth"
+- compatible: Should be
+		"mediatek,mt2701-eth": for MT2701 SoC
+		"mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC
+		"mediatek,mt7622-eth": for MT7622 SoC
 - reg: Address and length of the register set for the device
 - interrupts: Should contain the three frame engines interrupts in numeric
 	order. These are fe_int0, fe_int1 and fe_int2.
 - clocks: the clock used by the core
 - clock-names: the names of the clock listed in the clocks property. These are
-	"ethif", "esw", "gp2", "gp1"
+	"ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC
+        "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m",
+	"sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC
 - power-domains: phandle to the power domain that the ethernet is part of
 - resets: Should contain a phandle to the ethsys reset signal
 - reset-names: Should contain the reset signal name "eth"
 - mediatek,ethsys: phandle to the syscon node that handles the port setup
+- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
+	which is required for those SoCs equipped with SGMII such as MT7622 SoC.
 - mediatek,pctl: phandle to the syscon node that handles the ports slew rate
 	and driver current
 
 Optional properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
-
 * Ethernet MAC node
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index b55857696fc3..d3c24d5ffa9a 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -52,6 +52,11 @@ Optional Properties:
   Mark the corresponding energy efficient ethernet mode as broken and
   request the ethernet to stop advertising it.
 
+- phy-is-integrated: If set, indicates that the PHY is integrated into the same
+  physical package as the Ethernet MAC. If needed, muxers should be configured
+  to ensure the integrated PHY is used. The absence of this property indicates
+  the muxers should be configured so that the external PHY is used.
+
 Example:
 
 ethernet-phy@0 {
diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
index b519503be51a..16723535e1aa 100644
--- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
+++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -4,19 +4,25 @@ This file provides information on what the device node for the Ethernet AVB
 interface contains.
 
 Required properties:
-- compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
-	      "renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC.
-	      "renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC.
-	      "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC.
-	      "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
-	      "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
-	      "renesas,etheravb-r8a7796" if the device is a part of R8A7796 SoC.
-	      "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface.
-	      "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface.
+- compatible: Must contain one or more of the following:
+      - "renesas,etheravb-r8a7743" for the R8A7743 SoC.
+      - "renesas,etheravb-r8a7745" for the R8A7745 SoC.
+      - "renesas,etheravb-r8a7790" for the R8A7790 SoC.
+      - "renesas,etheravb-r8a7791" for the R8A7791 SoC.
+      - "renesas,etheravb-r8a7792" for the R8A7792 SoC.
+      - "renesas,etheravb-r8a7793" for the R8A7793 SoC.
+      - "renesas,etheravb-r8a7794" for the R8A7794 SoC.
+      - "renesas,etheravb-rcar-gen2" as a fallback for the above
+		R-Car Gen2 and RZ/G1 devices.
 
-	      When compatible with the generic version, nodes must list the
-	      SoC-specific version corresponding to the platform first
-	      followed by the generic version.
+      - "renesas,etheravb-r8a7795" for the R8A7795 SoC.
+      - "renesas,etheravb-r8a7796" for the R8A7796 SoC.
+      - "renesas,etheravb-rcar-gen3" as a fallback for the above
+		R-Car Gen3 devices.
+
+	When compatible with the generic version, nodes must list the
+	SoC-specific version corresponding to the platform first followed by
+	the generic version.
 
 - reg: offset and length of (1) the register block and (2) the stream buffer.
 - interrupts: A list of interrupt-specifiers, one for each entry in
diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
index 8f427550720a..c1325387632c 100644
--- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -10,6 +10,7 @@ Required properties:
    "rockchip,rk3366-gmac": found on RK3366 SoCs
    "rockchip,rk3368-gmac": found on RK3368 SoCs
    "rockchip,rk3399-gmac": found on RK3399 SoCs
+   "rockchip,rv1108-gmac": found on RV1108 SoCs
  - reg: addresses and length of the register sets for the device.
  - interrupts: Should contain the GMAC interrupts.
  - interrupt-names: Should contain the interrupt names "macirq".
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
new file mode 100644
index 000000000000..38f9ec076743
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
@@ -0,0 +1,55 @@
+XILINX AXI ETHERNET Device Tree Bindings
+--------------------------------------------------------
+
+Also called  AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
+provides connectivity to an external ethernet PHY supporting different
+interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
+segments of memory for buffering TX and RX, as well as the capability of
+offloading TX/RX checksum calculation off the processor.
+
+Management configuration is done through the AXI interface, while payload is
+sent and received through means of an AXI DMA controller. This driver
+includes the DMA driver code, so this driver is incompatible with AXI DMA
+driver.
+
+For more details about mdio please refer phy.txt file in the same directory.
+
+Required properties:
+- compatible	: Must be one of "xlnx,axi-ethernet-1.00.a",
+		  "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
+- reg		: Address and length of the IO space.
+- interrupts	: Should be a list of two interrupt, TX and RX.
+- phy-handle	: Should point to the external phy device.
+		  See ethernet.txt file in the same directory.
+- xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
+
+Optional properties:
+- phy-mode	: See ethernet.txt
+- xlnx,phy-type	: Deprecated, do not use, but still accepted in preference
+		  to phy-mode.
+- xlnx,txcsum	: 0 or empty for disabling TX checksum offload,
+		  1 to enable partial TX checksum offload,
+		  2 to enable full TX checksum offload
+- xlnx,rxcsum	: Same values as xlnx,txcsum but for RX checksum offload
+
+Example:
+	axi_ethernet_eth: ethernet@40c00000 {
+		compatible = "xlnx,axi-ethernet-1.00.a";
+		device_type = "network";
+		interrupt-parent = <&microblaze_0_axi_intc>;
+		interrupts = <2 0>;
+		phy-mode = "mii";
+		reg = <0x40c00000 0x40000>;
+		xlnx,rxcsum = <0x2>;
+		xlnx,rxmem = <0x800>;
+		xlnx,txcsum = <0x2>;
+		phy-handle = <&phy0>;
+		axi_ethernetlite_0_mdio: mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			phy0: phy@0 {
+				device_type = "ethernet-phy";
+				reg = <1>;
+			};
+		};
+	};