Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:

 - add framework for supporting PCIe devices in Endpoint mode (Kishon
   Vijay Abraham I)

 - use non-postable PCI config space mappings when possible (Lorenzo
   Pieralisi)

 - clean up and unify mmap of PCI BARs (David Woodhouse)

 - export and unify Function Level Reset support (Christoph Hellwig)

 - avoid FLR for Intel 82579 NICs (Sasha Neftin)

 - add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)

 - short-circuit config access failures for disconnected devices (Keith
   Busch)

 - remove D3 sleep delay when possible (Adrian Hunter)

 - freeze PME scan before suspending devices (Lukas Wunner)

 - stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)

 - disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)

 - add arch-specific alignment control to improve device passthrough by
   avoiding multiple BARs in a page (Yongji Xie)

 - add sysfs sriov_drivers_autoprobe to control VF driver binding
   (Bodong Wang)

 - allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)

 - fix crashes when unbinding host controllers that don't support
   removal (Brian Norris)

 - add driver for MicroSemi Switchtec management interface (Logan
   Gunthorpe)

 - add driver for Faraday Technology FTPCI100 host bridge (Linus
   Walleij)

 - add i.MX7D support (Andrey Smirnov)

 - use generic MSI support for Aardvark (Thomas Petazzoni)

 - make Rockchip driver modular (Brian Norris)

 - advertise 128-byte Read Completion Boundary support for Rockchip
   (Shawn Lin)

 - advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)

 - convert atomic_t to refcount_t in HV driver (Elena Reshetova)

 - add CPU IRQ affinity in HV driver (K. Y. Srinivasan)

 - fix PCI bus removal in HV driver (Long Li)

 - add support for ThunderX2 DMA alias topology (Jayachandran C)

 - add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)

 - add ITE 8893 bridge DMA alias quirk (Jarod Wilson)

 - restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
   (Manish Jaggi)

* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
  PCI: Don't allow unbinding host controllers that aren't prepared
  ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
  MAINTAINERS: Add PCI Endpoint maintainer
  Documentation: PCI: Add userguide for PCI endpoint test function
  tools: PCI: Add sample test script to invoke pcitest
  tools: PCI: Add a userspace tool to test PCI endpoint
  Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
  misc: Add host side PCI driver for PCI test function device
  PCI: Add device IDs for DRA74x and DRA72x
  dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
  PCI: dwc: dra7xx: Workaround for errata id i870
  dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
  PCI: dwc: dra7xx: Add EP mode support
  PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
  dt-bindings: PCI: Add DT bindings for PCI designware EP mode
  PCI: dwc: designware: Add EP mode support
  Documentation: PCI: Add binding documentation for pci-test endpoint function
  ixgbe: Use pcie_flr() instead of duplicating it
  IB/hfi1: Use pcie_flr() instead of duplicating it
  PCI: imx6: Fix spelling mistake: "contol" -> "control"
  ...

1 files changed, 35 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
index 60e25161f351..6a07c96227e0 100644
--- a/Documentation/devicetree/bindings/pci/ti-pci.txt
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -1,17 +1,22 @@
 TI PCI Controllers
 
 PCIe Designware Controller
- - compatible: Should be "ti,dra7-pcie""
- - reg : Two register ranges as listed in the reg-names property
- - reg-names : The first entry must be "ti-conf" for the TI specific registers
-	       The second entry must be "rc-dbics" for the designware pcie
-	       registers
-	       The third entry must be "config" for the PCIe configuration space
+ - compatible: Should be "ti,dra7-pcie" for RC
+	       Should be "ti,dra7-pcie-ep" for EP
  - phys : list of PHY specifiers (used by generic PHY framework)
  - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
 	       number of PHYs as specified in *phys* property.
  - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
 	       where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../designware-pcie.txt
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI specific registers
+	       The second entry must be "rc-dbics" for the DesignWare PCIe
+	       registers
+	       The third entry must be "config" for the PCIe configuration space
  - interrupts : Two interrupt entries must be specified. The first one is for
 		main interrupt line and the second for MSI interrupt line.
  - #address-cells,
@@ -19,13 +24,36 @@ PCIe Designware Controller
    #interrupt-cells,
    device_type,
    ranges,
-   num-lanes,
    interrupt-map-mask,
    interrupt-map : as specified in ../designware-pcie.txt
 
+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI specific registers
+	       "ep_dbics" for the standard configuration registers as
+		they are locally accessed within the DIF CS space
+	       "ep_dbics2" for the standard configuration registers as
+		they are locally accessed within the DIF CS2 space
+	       "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+ - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
+			       should contain the register offset within syscon
+			       and the 2nd argument should contain the bit field
+			       for setting the bit to enable unaligned
+			       access.
+
 Optional Property:
  - gpios : Should be added if a gpio line is required to drive PERST# line
 
+NOTE: Two DT nodes may be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode DT node should be disabled and in order to PCI to
+work in EP mode, host mode DT node should be disabled. Host mode and EP
+mode are mutually exclusive.
+
 Example:
 axi {
 	compatible = "simple-bus";