Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Omap fixes and minor defconfig updates that would be good to
get in before -rc1.

* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
  ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
  ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
  ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
  ARM: OMAP2+: devices: remove duplicated include from devices.c
  ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
  ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
  ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
  ARM: OMAP2+: Remove obsolete Makefile line
  ARM: OMAP5: Enable Cortex A15 errata 798181
  ARM: scu: provide inline dummy functions when SCU is not present
  ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
  ARM: OMAP2+: timer: initialize before using oh_name

Signed-off-by: Olof Johansson <olof@lixom.net>

Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.

1 files changed, 48 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index c95ea8278f87..aeb3c995cc04 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -126,3 +126,51 @@ device; they may be grandchildren, for example. Whether this is legal, and
 whether there is any interaction between the child and intermediate parent
 nodes, is again defined entirely by the binding for the individual pin
 controller device.
+
+== Using generic pinconfig options ==
+
+Generic pinconfig parameters can be used by defining a separate node containing
+the applicable parameters (and optional values), like:
+
+pcfg_pull_up: pcfg_pull_up {
+	bias-pull-up;
+	drive-strength = <20>;
+};
+
+This node should then be referenced in the appropriate pinctrl node as a phandle
+and parsed in the driver using the pinconf_generic_parse_dt_config function.
+
+Supported configuration parameters are:
+
+bias-disable		- disable any pin bias
+bias-high-impedance	- high impedance mode ("third-state", "floating")
+bias-bus-hold		- latch weakly
+bias-pull-up		- pull up the pin
+bias-pull-down		- pull down the pin
+bias-pull-pin-default	- use pin-default pull state
+drive-push-pull		- drive actively high and low
+drive-open-drain	- drive with open drain
+drive-open-source	- drive with open source
+drive-strength		- sink or source at most X mA
+input-schmitt-enable	- enable schmitt-trigger mode
+input-schmitt-disable	- disable schmitt-trigger mode
+input-debounce		- debounce mode with debound time X
+low-power-enable	- enable low power mode
+low-power-disable	- disable low power mode
+output-low		- set the pin to output mode with low level
+output-high		- set the pin to output mode with high level
+
+Arguments for parameters:
+
+- bias-pull-up, -down and -pin-default take as optional argument on hardware
+  supporting it the pull strength in Ohm. bias-disable will disable the pull.
+
+- drive-strength takes as argument the target strength in mA.
+
+- input-debounce takes the debounce time in usec as argument
+  or 0 to disable debouncing
+
+All parameters not listed here, do not take an argument.
+
+More in-depth documentation on these parameters can be found in
+<include/linux/pinctrl/pinconfig-generic.h>