Merge tag 'v4.14-rc6' into next

Merge with mainline to bring in the timer API changes.

5 files changed, 84 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/reset/lantiq,reset.txt b/Documentation/devicetree/bindings/reset/lantiq,reset.txt
new file mode 100644
index 000000000000..c6aef36b7d15
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/lantiq,reset.txt
@@ -0,0 +1,30 @@
+Lantiq XWAY SoC RCU reset controller binding
+============================================
+
+This binding describes a reset-controller found on the RCU module on Lantiq
+XWAY SoCs.
+
+This node has to be a sub node of the Lantiq RCU block.
+
+-------------------------------------------------------------------------------
+Required properties:
+- compatible		: Should be one of
+				"lantiq,danube-reset"
+				"lantiq,xrx200-reset"
+- reg			: Defines the following sets of registers in the parent
+			  syscon device
+			- Offset of the reset set register
+			- Offset of the reset status register
+- #reset-cells		: Specifies the number of cells needed to encode the
+			  reset line, should be 2.
+			  The first cell takes the reset set bit and the
+			  second cell takes the status bit.
+
+-------------------------------------------------------------------------------
+Example for the reset-controllers on the xRX200 SoCs:
+	reset0: reset-controller@10 {
+		compatible = "lantiq,xrx200-reset";
+		reg <0x10 0x04>, <0x14 0x04>;
+
+		#reset-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt
index b4e96a278445..05d5be48dae4 100644
--- a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt
+++ b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt
@@ -80,5 +80,4 @@ mac: ethernet@40010000 {
 	clock-names = "stmmaceth";
 	resets = <&rgu 22>;
 	reset-names = "stmmaceth";
-	status = "disabled";
 };
diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt
index fe5e0f37b3c9..e5a03ffe04fb 100644
--- a/Documentation/devicetree/bindings/reset/renesas,rst.txt
+++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt
@@ -26,6 +26,7 @@ Required properties:
 		  - "renesas,r8a7794-rst" (R-Car E2)
 		  - "renesas,r8a7795-rst" (R-Car H3)
 		  - "renesas,r8a7796-rst" (R-Car M3-W)
+		  - "renesas,r8a77995-rst" (R-Car D3)
   - reg: Address start and address range for the device.
 
 
diff --git a/Documentation/devicetree/bindings/reset/snps,hsdk-reset.txt b/Documentation/devicetree/bindings/reset/snps,hsdk-reset.txt
new file mode 100644
index 000000000000..830069b1c37c
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/snps,hsdk-reset.txt
@@ -0,0 +1,28 @@
+Binding for the Synopsys HSDK reset controller
+
+This binding uses the common reset binding[1].
+
+[1] Documentation/devicetree/bindings/reset/reset.txt
+
+Required properties:
+- compatible: should be "snps,hsdk-reset".
+- reg: should always contain 2 pairs address - length: first for reset
+  configuration register and second for corresponding SW reset and status bits
+  register.
+- #reset-cells: from common reset binding; Should always be set to 1.
+
+Example:
+	reset: reset@880 {
+		compatible = "snps,hsdk-reset";
+		#reset-cells = <1>;
+		reg = <0x8A0 0x4>, <0xFF0 0x4>;
+	};
+
+Specifying reset lines connected to IP modules:
+	ethernet@.... {
+		....
+		resets = <&reset HSDK_V1_ETH_RESET>;
+		....
+	};
+
+The index could be found in <dt-bindings/reset/snps,hsdk-reset.h>
diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt
index 83ab0f599c40..68a6f487c409 100644
--- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt
+++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt
@@ -6,7 +6,6 @@ System reset
 
 Required properties:
 - compatible: should be one of the following:
-    "socionext,uniphier-sld3-reset" - for sLD3 SoC
     "socionext,uniphier-ld4-reset"  - for LD4 SoC
     "socionext,uniphier-pro4-reset" - for Pro4 SoC
     "socionext,uniphier-sld8-reset" - for sLD8 SoC
@@ -37,7 +36,6 @@ Media I/O (MIO) reset, SD reset
 
 Required properties:
 - compatible: should be one of the following:
-    "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC
     "socionext,uniphier-ld4-mio-reset"  - for LD4 SoC
     "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC
     "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC
@@ -92,3 +90,28 @@ Example:
 
 		other nodes ...
 	};
+
+
+Analog signal amplifier reset
+-----------------------------
+
+Required properties:
+- compatible: should be one of the following:
+    "socionext,uniphier-ld11-adamv-reset" - for LD11 SoC
+    "socionext,uniphier-ld20-adamv-reset" - for LD20 SoC
+- #reset-cells: should be 1.
+
+Example:
+
+	adamv@57920000 {
+		compatible = "socionext,uniphier-ld11-adamv",
+			     "simple-mfd", "syscon";
+		reg = <0x57920000 0x1000>;
+
+		adamv_rst: reset {
+			compatible = "socionext,uniphier-ld11-adamv-reset";
+			#reset-cells = <1>;
+		};
+
+		other nodes ...
+	};