Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "As usual, there are lots of minor driver changes across SoC platforms
  from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
  These usually add support for additional chip variations in existing
  drivers, but also add features or bugfixes.

  The SCMI firmware subsystem gains a unified raw userspace interface
  through debugfs, which can be used for validation purposes.

  Newly added drivers include:

   - New power management drivers for StarFive JH7110, Allwinner D1 and
     Renesas RZ/V2M

   - A driver for Qualcomm battery and power supply status

   - A SoC device driver for identifying Nuvoton WPCM450 chips

   - A regulator coupler driver for Mediatek MT81xxv"

* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  power: supply: Introduce Qualcomm PMIC GLINK power supply
  soc: apple: rtkit: Do not copy the reg state structure to the stack
  soc: sunxi: SUN20I_PPU should depend on PM
  memory: renesas-rpc-if: Remove redundant division of dummy
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  ...

9 files changed, 427 insertions, 76 deletions

diff --git a/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml b/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
index 9241e5fc7cff..15c133cac315 100644
--- a/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
+++ b/Documentation/devicetree/bindings/soc/mediatek/mediatek,mutex.yaml
@@ -32,6 +32,7 @@ properties:
       - mediatek,mt8183-disp-mutex
       - mediatek,mt8186-disp-mutex
       - mediatek,mt8186-mdp3-mutex
+      - mediatek,mt8188-disp-mutex
       - mediatek,mt8192-disp-mutex
       - mediatek,mt8195-disp-mutex
 
diff --git a/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml b/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
new file mode 100644
index 000000000000..3fefd634bc69
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml
@@ -0,0 +1,147 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/mediatek/mediatek,pwrap.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek PMIC Wrapper
+
+maintainers:
+  - Flora Fu <flora.fu@mediatek.com>
+  - Alexandre Mergnat <amergnat@baylibre.com>
+
+description:
+  On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface
+  is not directly visible to the CPU, but only through the PMIC wrapper
+  inside the SoC. The communication between the SoC and the PMIC can
+  optionally be encrypted. Also a non standard Dual IO SPI mode can be
+  used to increase speed.
+
+  IP Pairing
+
+  On MT8135 the pins of some SoC internal peripherals can be on the PMIC.
+  The signals of these pins are routed over the SPI bus using the pwrap
+  bridge. In the binding description below the properties needed for bridging
+  are marked with "IP Pairing". These are optional on SoCs which do not support
+  IP Pairing
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - mediatek,mt2701-pwrap
+              - mediatek,mt6765-pwrap
+              - mediatek,mt6779-pwrap
+              - mediatek,mt6797-pwrap
+              - mediatek,mt6873-pwrap
+              - mediatek,mt7622-pwrap
+              - mediatek,mt8135-pwrap
+              - mediatek,mt8173-pwrap
+              - mediatek,mt8183-pwrap
+              - mediatek,mt8186-pwrap
+              - mediatek,mt8188-pwrap
+              - mediatek,mt8195-pwrap
+              - mediatek,mt8365-pwrap
+              - mediatek,mt8516-pwrap
+      - items:
+          - enum:
+              - mediatek,mt8186-pwrap
+              - mediatek,mt8195-pwrap
+          - const: syscon
+
+  reg:
+    minItems: 1
+    items:
+      - description: PMIC wrapper registers
+      - description: IP pairing registers
+
+  reg-names:
+    minItems: 1
+    items:
+      - const: pwrap
+      - const: pwrap-bridge
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    items:
+      - description: SPI bus clock
+      - description: Main module clock
+      - description: System module clock
+      - description: Timer module clock
+
+  clock-names:
+    minItems: 2
+    items:
+      - const: spi
+      - const: wrap
+      - const: sys
+      - const: tmr
+
+  resets:
+    minItems: 1
+    items:
+      - description: PMIC wrapper reset
+      - description: IP pairing reset
+
+  reset-names:
+    minItems: 1
+    items:
+      - const: pwrap
+      - const: pwrap-bridge
+
+  pmic:
+    type: object
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+
+dependentRequired:
+  resets: [reset-names]
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt8365-pwrap
+    then:
+      properties:
+        clocks:
+          minItems: 4
+
+        clock-names:
+          minItems: 4
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/mt8135-resets.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        pwrap@1000f000 {
+            compatible = "mediatek,mt8135-pwrap";
+            reg = <0 0x1000f000 0 0x1000>,
+                  <0 0x11017000 0 0x1000>;
+            reg-names = "pwrap", "pwrap-bridge";
+            interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&clk26m>, <&clk26m>;
+            clock-names = "spi", "wrap";
+            resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>,
+                     <&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>;
+            reset-names = "pwrap", "pwrap-bridge";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
deleted file mode 100644
index 12e4b4260b40..000000000000
--- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
+++ /dev/null
@@ -1,75 +0,0 @@
-MediaTek PMIC Wrapper Driver
-
-This document describes the binding for the MediaTek PMIC wrapper.
-
-On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface
-is not directly visible to the CPU, but only through the PMIC wrapper
-inside the SoC. The communication between the SoC and the PMIC can
-optionally be encrypted. Also a non standard Dual IO SPI mode can be
-used to increase speed.
-
-IP Pairing
-
-on MT8135 the pins of some SoC internal peripherals can be on the PMIC.
-The signals of these pins are routed over the SPI bus using the pwrap
-bridge. In the binding description below the properties needed for bridging
-are marked with "IP Pairing". These are optional on SoCs which do not support
-IP Pairing
-
-Required properties in pwrap device node.
-- compatible:
-	"mediatek,mt2701-pwrap" for MT2701/7623 SoCs
-	"mediatek,mt6765-pwrap" for MT6765 SoCs
-	"mediatek,mt6779-pwrap" for MT6779 SoCs
-	"mediatek,mt6797-pwrap" for MT6797 SoCs
-	"mediatek,mt6873-pwrap" for MT6873/8192 SoCs
-	"mediatek,mt7622-pwrap" for MT7622 SoCs
-	"mediatek,mt8135-pwrap" for MT8135 SoCs
-	"mediatek,mt8173-pwrap" for MT8173 SoCs
-	"mediatek,mt8183-pwrap" for MT8183 SoCs
-	"mediatek,mt8186-pwrap" for MT8186 SoCs
-	"mediatek,mt8188-pwrap", "mediatek,mt8195-pwrap" for MT8188 SoCs
-	"mediatek,mt8195-pwrap" for MT8195 SoCs
-	"mediatek,mt8365-pwrap" for MT8365 SoCs
-	"mediatek,mt8516-pwrap" for MT8516 SoCs
-- interrupts: IRQ for pwrap in SOC
-- reg-names: "pwrap" is required; "pwrap-bridge" is optional.
-  "pwrap": Main registers base
-  "pwrap-bridge": bridge base (IP Pairing)
-- reg: Must contain an entry for each entry in reg-names.
-- clock-names: Must include the following entries:
-  "spi": SPI bus clock
-  "wrap": Main module clock
-  "sys": Optional system module clock
-  "tmr": Optional timer module clock
-- clocks: Must contain an entry for each entry in clock-names.
-
-Optional properities:
-- reset-names: Some SoCs include the following entries:
-  "pwrap"
-  "pwrap-bridge" (IP Pairing)
-- resets: Must contain an entry for each entry in reset-names.
-- pmic: Using either MediaTek PMIC MFD as the child device of pwrap
-  See the following for child node definitions:
-  Documentation/devicetree/bindings/mfd/mt6397.txt
-  or the regulator-only device as the child device of pwrap, such as MT6380.
-  See the following definitions for such kinds of devices.
-  Documentation/devicetree/bindings/regulator/mt6380-regulator.txt
-
-Example:
-	pwrap: pwrap@1000f000 {
-		compatible = "mediatek,mt8135-pwrap";
-		reg = <0 0x1000f000 0 0x1000>,
-			<0 0x11017000 0 0x1000>;
-		reg-names = "pwrap", "pwrap-bridge";
-		interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
-		resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>,
-				<&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>;
-		reset-names = "pwrap", "pwrap-bridge";
-		clocks = <&clk26m>, <&clk26m>;
-		clock-names = "spi", "wrap";
-
-		pmic {
-			compatible = "mediatek,mt6397";
-		};
-	};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml
new file mode 100644
index 000000000000..ce7e20dd22c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,dcc.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,dcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Data Capture and Compare
+
+maintainers:
+  - Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+
+description: |
+    DCC (Data Capture and Compare) is a DMA engine which is used to save
+    configuration data or system memory contents during catastrophic failure
+    or SW trigger. DCC is used to capture and store data for debugging purpose
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,sm8150-dcc
+          - qcom,sc7280-dcc
+          - qcom,sc7180-dcc
+          - qcom,sdm845-dcc
+      - const: qcom,dcc
+
+  reg:
+    items:
+      - description: DCC base
+      - description: DCC RAM base
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    dma@10a2000{
+        compatible = "qcom,sm8150-dcc", "qcom,dcc";
+        reg = <0x010a2000 0x1000>,
+              <0x010ad000 0x2000>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml
new file mode 100644
index 000000000000..aae9cf7b8caf
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,msm8976-ramp-controller.yaml
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,msm8976-ramp-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Ramp Controller
+
+maintainers:
+  - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
+
+description:
+  The Ramp Controller is used to program the sequence ID for pulse
+  swallowing, enable sequences and link Sequence IDs (SIDs) for the
+  CPU cores on some Qualcomm SoCs.
+
+properties:
+  compatible:
+    enum:
+      - qcom,msm8976-ramp-controller
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    cpu-power-controller@b014000 {
+        compatible = "qcom,msm8976-ramp-controller";
+        reg = <0x0b014000 0x68>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
new file mode 100644
index 000000000000..cf863683c21a
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,pmic-glink.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PMIC GLINK firmware interface for battery management, USB
+  Type-C and other things.
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+
+description:
+  The PMIC GLINK service, running on a coprocessor on some modern Qualcomm
+  platforms and implement USB Type-C handling and battery management. This
+  binding describes the component in the OS used to communicate with the
+  firmware and connect it's resources to those described in the Devicetree,
+  particularly the USB Type-C controllers relationship with USB and DisplayPort
+  components.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,sc8180x-pmic-glink
+          - qcom,sc8280xp-pmic-glink
+          - qcom,sm8350-pmic-glink
+      - const: qcom,pmic-glink
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  '^connector@\d$':
+    $ref: /schemas/connector/usb-connector.yaml#
+
+    properties:
+      reg: true
+
+    required:
+      - reg
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |+
+    pmic-glink {
+        compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        connector@0 {
+            compatible = "usb-c-connector";
+            reg = <0>;
+            power-role = "dual";
+            data-role = "dual";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    endpoint {
+                        remote-endpoint = <&usb_role>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&ss_phy_out>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+                    endpoint {
+                        remote-endpoint = <&sbu_mux>;
+                    };
+                };
+            };
+        };
+    };
+...
+
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml
new file mode 100644
index 000000000000..b00be9e01206
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,rpm.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,rpm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Resource Power Manager (RPM)
+
+description:
+  This driver is used to interface with the Resource Power Manager (RPM) found
+  in various Qualcomm platforms. The RPM allows each component in the system
+  to vote for state of the system resources, such as clocks, regulators and bus
+  frequencies.
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+
+properties:
+  compatible:
+    enum:
+      - qcom,rpm-apq8064
+      - qcom,rpm-msm8660
+      - qcom,rpm-msm8960
+      - qcom,rpm-ipq8064
+      - qcom,rpm-mdm9615
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 3
+
+  interrupt-names:
+    items:
+      - const: ack
+      - const: err
+      - const: wakeup
+
+  qcom,ipc:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to a syscon node representing the APCS registers
+          - description: u32 representing offset to the register within the syscon
+          - description: u32 representing the ipc bit within the register
+    description:
+      Three entries specifying the outgoing ipc bit used for signaling the RPM.
+
+patternProperties:
+  "^regulators(-[01])?$":
+    type: object
+    $ref: /schemas/regulator/qcom,rpm-regulator.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - qcom,ipc
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/mfd/qcom-rpm.h>
+
+    rpm@108000 {
+      compatible = "qcom,rpm-msm8960";
+      reg = <0x108000 0x1000>;
+      qcom,ipc = <&apcs 0x8 2>;
+
+      interrupts = <GIC_SPI 19 IRQ_TYPE_NONE>, <GIC_SPI 21 IRQ_TYPE_NONE>, <GIC_SPI 22 IRQ_TYPE_NONE>;
+      interrupt-names = "ack", "err", "wakeup";
+
+      regulators {
+        compatible = "qcom,rpm-pm8921-regulators";
+        vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+        s1 {
+          regulator-min-microvolt = <1225000>;
+          regulator-max-microvolt = <1225000>;
+
+          bias-pull-down;
+
+          qcom,switch-mode-frequency = <3200000>;
+        };
+
+        pm8921_s4: s4 {
+          regulator-min-microvolt = <1800000>;
+          regulator-max-microvolt = <1800000>;
+
+          qcom,switch-mode-frequency = <1600000>;
+          bias-pull-down;
+
+          qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+        };
+      };
+    };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
index b246500d3d5d..a4046ba60846 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
@@ -112,8 +112,9 @@ properties:
     $ref: /schemas/power/qcom,rpmpd.yaml#
 
 patternProperties:
-  '-regulators$':
+  '^regulators(-[0-9])?$':
     $ref: /schemas/regulator/qcom,rpmh-regulator.yaml#
+    unevaluatedProperties: false
 
 required:
   - compatible
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
index 11c0f4dd797c..16fd67c0bd1f 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -80,6 +80,7 @@ if:
         enum:
           - qcom,rpm-apq8084
           - qcom,rpm-msm8916
+          - qcom,rpm-msm8936
           - qcom,rpm-msm8974
           - qcom,rpm-msm8976
           - qcom,rpm-msm8953