Merge tag 'xceiv-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:
	usb: xceiv: patches for v3.9 merge window

	Two new PHY drivers coming here: one for Samsung,
	one for OMAP. Both architectures are adding USB3
	support to mainline kernel.

	The PHY layer now allows us to have mulitple PHYs
	of the same type, which is necessary for platforms
	which provide more than one USB peripheral port.

	There's also a few cleanups here: removal of __dev*
	annotations, conversion of a cast to to_delayed_work(),
	and mxs-phy learns about ->set_suspend.

4 files changed, 140 insertions, 6 deletions

diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
new file mode 100644
index 000000000000..7a95c651ceb3
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -0,0 +1,22 @@
+synopsys DWC3 CORE
+
+DWC3- USB3 CONTROLLER
+
+Required properties:
+ - compatible: must be "synopsys,dwc3"
+ - reg : Address and length of the register set for the device
+ - interrupts: Interrupts used by the dwc3 controller.
+ - usb-phy : array of phandle for the PHY device
+
+Optional properties:
+ - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
+
+This is usually a subnode to DWC3 glue to which it is connected.
+
+dwc3@4a030000 {
+	compatible = "synopsys,dwc3";
+	reg = <0x4a030000 0xcfff>;
+	interrupts = <0 92 4>
+	usb-phy = <&usb2_phy>, <&usb3,phy>;
+	tx-fifo-resize;
+};
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 29a043ecda52..1ef0ce71f8fa 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -1,8 +1,11 @@
-OMAP GLUE
+OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
 
 OMAP MUSB GLUE
  - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
  - ti,hwmods : must be "usb_otg_hs"
+ - ti,has-mailbox : to specify that omap uses an external mailbox
+   (in control module) to communicate with the musb core during device connect
+   and disconnect.
  - multipoint : Should be "1" indicating the musb controller supports
    multipoint. This is a MUSB configuration-specific setting.
  - num_eps : Specifies the number of endpoints. This is also a
@@ -16,13 +19,19 @@ OMAP MUSB GLUE
  - power : Should be "50". This signifies the controller can supply upto
    100mA when operating in host mode.
 
+Optional properties:
+ - ctrl-module : phandle of the control module this glue uses to write to
+   mailbox
+
 SOC specific device node entry
 usb_otg_hs: usb_otg_hs@4a0ab000 {
 	compatible = "ti,omap4-musb";
 	ti,hwmods = "usb_otg_hs";
+	ti,has-mailbox;
 	multipoint = <1>;
 	num_eps = <16>;
 	ram_bits = <12>;
+	ctrl-module = <&omap_control_usb>;
 };
 
 Board specific device node entry
@@ -31,3 +40,26 @@ Board specific device node entry
 	mode = <3>;
 	power = <50>;
 };
+
+OMAP CONTROL USB
+
+Required properties:
+ - compatible: Should be "ti,omap-control-usb"
+ - reg : Address and length of the register set for the device. It contains
+   the address of "control_dev_conf" and "otghs_control" or "phy_power_usb"
+   depending upon omap4 or omap5.
+ - reg-names: The names of the register addresses corresponding to the registers
+   filled in "reg".
+ - ti,type: This is used to differentiate whether the control module has
+   usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to
+   notify events to the musb core and omap5 has usb3 phy power register to
+   power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3
+   phy power.
+
+omap_control_usb: omap-control-usb@4a002300 {
+	compatible = "ti,omap-control-usb";
+	reg = <0x4a002300 0x4>,
+	      <0x4a00233c 0x4>;
+	reg-names = "control_dev_conf", "otghs_control";
+	ti,type = <1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
new file mode 100644
index 000000000000..033194934f64
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
@@ -0,0 +1,55 @@
+* Samsung's usb phy transceiver
+
+The Samsung's phy transceiver is used for controlling usb phy for
+s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers
+across Samsung SOCs.
+TODO: Adding the PHY binding with controller(s) according to the under
+developement generic PHY driver.
+
+Required properties:
+
+Exynos4210:
+- compatible : should be "samsung,exynos4210-usbphy"
+- reg : base physical address of the phy registers and length of memory mapped
+	region.
+
+Exynos5250:
+- compatible : should be "samsung,exynos5250-usbphy"
+- reg : base physical address of the phy registers and length of memory mapped
+	region.
+
+Optional properties:
+- #address-cells: should be '1' when usbphy node has a child node with 'reg'
+		  property.
+- #size-cells: should be '1' when usbphy node has a child node with 'reg'
+	       property.
+- ranges: allows valid translation between child's address space and parent's
+	  address space.
+
+- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller
+  interface for usb-phy. It should provide the following information required by
+  usb-phy controller to control phy.
+  - reg : base physical address of PHY_CONTROL registers.
+	  The size of this register is the total sum of size of all PHY_CONTROL
+	  registers that the SoC has. For example, the size will be
+	  '0x4' in case we have only one PHY_CONTROL register (e.g.
+	  OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210)
+	  and, '0x8' in case we have two PHY_CONTROL registers (e.g.
+	  USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x).
+	  and so on.
+
+Example:
+ - Exynos4210
+
+	usbphy@125B0000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,exynos4210-usbphy";
+		reg = <0x125B0000 0x100>;
+		ranges;
+
+		usbphy-sys {
+			/* USB device and host PHY_CONTROL registers */
+			reg = <0x10020704 0x8>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 80d4148cb661..61496f5cb095 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -4,14 +4,39 @@ OMAP USB2 PHY
 
 Required properties:
  - compatible: Should be "ti,omap-usb2"
- - reg : Address and length of the register set for the device. Also
-add the address of control module dev conf register until a driver for
-control module is added
+ - reg : Address and length of the register set for the device.
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
 
 This is usually a subnode of ocp2scp to which it is connected.
 
 usb2phy@4a0ad080 {
 	compatible = "ti,omap-usb2";
-	reg = <0x4a0ad080 0x58>,
-	      <0x4a002300 0x4>;
+	reg = <0x4a0ad080 0x58>;
+	ctrl-module = <&omap_control_usb>;
+};
+
+OMAP USB3 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb3"
+ - reg : Address and length of the register set for the device.
+ - reg-names: The names of the register addresses corresponding to the registers
+   filled in "reg".
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb3phy@4a084400 {
+	compatible = "ti,omap-usb3";
+	reg = <0x4a084400 0x80>,
+	      <0x4a084800 0x64>,
+	      <0x4a084c00 0x40>;
+	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+	ctrl-module = <&omap_control_usb>;
 };