Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v3.20 merge window

Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.

The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.

Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.

Signed-off-by: Felipe Balbi <balbi@ti.com>

4 files changed, 19 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index bc2222ca3f2a..38fee0f66c12 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -51,7 +51,10 @@ usb1: gadget@fffa4000 {
 Atmel High-Speed USB device controller
 
 Required properties:
- - compatible: Should be "atmel,at91sam9rl-udc"
+ - compatible: Should be one of the following
+	       "at91sam9rl-udc"
+	       "at91sam9g45-udc"
+	       "sama5d3-udc"
  - reg: Address and length of the register set for the device
  - interrupts: Should contain usba interrupt
  - ep childnode: To specify the number of endpoints and their properties.
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 482f815363ef..fd132cbee70e 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -20,6 +20,10 @@ Optional properties:
 Refer to phy/phy-bindings.txt for generic phy consumer properties
 - dr_mode: shall be one of "host", "peripheral" and "otg"
   Refer to usb/generic.txt
+- g-use-dma: enable dma usage in gadget driver.
+- g-rx-fifo-size: size of rx fifo size in gadget mode.
+- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
+- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index b08c903f8668..61b045b6d50e 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -14,6 +14,8 @@ Optional properties:
 			 function should be enabled
   - phys: phandle + phy specifier pair
   - phy-names: must be "usb"
+  - dmas: Must contain a list of references to DMA specifiers.
+  - dma-names : Must contain a list of DMA names, "tx" or "rx".
 
 Example:
 	usbhs: usb@e6590000 {
diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
index 1bd37faba05b..5be01c859b7a 100644
--- a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
+++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
@@ -13,10 +13,15 @@ Optional properties:
 - clock-frequency: the clock frequency (in Hz) that the PHY clock must
   be configured to.
 
-- vcc-supply: phandle to the regulator that provides RESET to the PHY.
+- vcc-supply: phandle to the regulator that provides power to the PHY.
 
 - reset-gpios: Should specify the GPIO for reset.
 
+- vbus-detect-gpio: should specify the GPIO detecting a VBus insertion
+                    (see Documentation/devicetree/bindings/gpio/gpio.txt)
+- vbus-regulator : should specifiy the regulator supplying current drawn from
+  the VBus line (see Documentation/devicetree/bindings/regulator/regulator.txt).
+
 Example:
 
 	hsusb1_phy {
@@ -26,8 +31,11 @@ Example:
 		clock-names = "main_clk";
 		vcc-supply = <&hsusb1_vcc_regulator>;
 		reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		vbus-detect-gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		vbus-regulator = <&vbus_regulator>;
 	};
 
 hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator
 and expects that clock to be configured to 19.2MHz by the NOP PHY driver.
 hsusb1_vcc_regulator provides power to the PHY and GPIO 7 controls RESET.
+GPIO 13 detects VBus insertion, and accordingly notifies the vbus-regulator.