Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	drivers/net/bonding/bond_3ad.h
	drivers/net/bonding/bond_main.c

Two minor conflicts in bonding, both of which were overlapping
changes.

Signed-off-by: David S. Miller <davem@davemloft.net>

5 files changed, 120 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
index 0a85c70cd30a..07ad02075a93 100644
--- a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
+++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
@@ -13,6 +13,9 @@ Required properties:
 - #address-cells: should be one. The cell is the slot id.
 - #size-cells: should be zero.
 - at least one slot node
+- clock-names: tuple listing input clock names.
+	Required elements: "mci_clk"
+- clocks: phandles to input clocks.
 
 The node contains child nodes for each slot that the platform uses
 
@@ -24,6 +27,8 @@ mmc0: mmc@f0008000 {
 	interrupts = <12 4>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	clock-names = "mci_clk";
+	clocks = <&mci0_clk>;
 
 	[ child node definitions...]
 };
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 000000000000..3dd3d0bf112f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible	: Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+   "st,stid127-dwmac".
+ - reg		: Offset of the glue configuration register map in system
+   configuration regmap pointed by st,syscon property and size.
+
+ - reg-names	: Should be "sti-ethconf".
+
+ - st,syscon	: Should be phandle to system configuration node which
+   encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+   wired up in from different sources. One via TXCLK pin and other via CLK_125
+   pin. This wiring is totally board dependent. However the retiming glue
+   logic should be configured accordingly. Possible values for this property
+
+	   "txclk" - if 125Mhz clock is wired up via txclk line.
+	   "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+   This property is only valid for Giga bit setup( GMII, RGMII), and it is
+   un-used for non-giga bit (MII and RMII) setups. Also note that internal
+   clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+  for tx and rx. This property is only valid for RMII case where the clock can
+  be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+	device_type 	= "network";
+	compatible	= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+	reg 		= <0xfe810000 0x8000>, <0x8bc 0x4>;
+	reg-names	= "stmmaceth", "sti-ethconf";
+	interrupts	= <0 133 0>, <0 134 0>, <0 135 0>;
+	interrupt-names	= "macirq", "eth_wake_irq", "eth_lpi";
+	phy-mode	= "mii";
+
+	st,syscon	= <&syscfg_rear>;
+
+	snps,pbl 	= <32>;
+	snps,mixed-burst;
+
+	resets		= <&softreset STIH416_ETH0_SOFTRESET>;
+	reset-names	= "stmmaceth";
+	pinctrl-0	= <&pinctrl_mii0>;
+	pinctrl-names 	= "default";
+	clocks		= <&CLK_S_GMAC0_PHY>;
+	clock-names	= "stmmaceth";
+};
diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/bq2415x.txt
new file mode 100644
index 000000000000..d0327f0b59ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/bq2415x.txt
@@ -0,0 +1,47 @@
+Binding for TI bq2415x Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24150"
+ * "ti,bq24150"
+ * "ti,bq24150a"
+ * "ti,bq24151"
+ * "ti,bq24151a"
+ * "ti,bq24152"
+ * "ti,bq24153"
+ * "ti,bq24153a"
+ * "ti,bq24155"
+ * "ti,bq24156"
+ * "ti,bq24156a"
+ * "ti,bq24158"
+- reg:			   integer, i2c address of the device.
+- ti,current-limit:	   integer, initial maximum current charger can pull
+			   from power supply in mA.
+- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
+			   The chip will use slow precharge if battery voltage
+			   is below this value.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
+- ti,charge-current:	   integer, maximum charging current in mA.
+- ti,termination-current:  integer, charge will be terminated when current in
+			   constant-voltage phase drops below this value (in mA).
+- ti,resistor-sense:	   integer, value of sensing resistor in milliohm.
+
+Optional properties:
+- ti,usb-charger-detection: phandle to usb charger detection device.
+			    (required for auto mode)
+
+Example from Nokia N900:
+
+bq24150a {
+	compatible = "ti,bq24150a";
+	reg = <0x6b>;
+
+	ti,current-limit = <100>;
+	ti,weak-battery-voltage = <3400>;
+	ti,battery-regulation-voltage = <4200>;
+	ti,charge-current = <650>;
+	ti,termination-current = <100>;
+	ti,resistor-sense = <68>;
+
+	ti,usb-charger-detection = <&isp1704>;
+};
diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt
index 07e04cdc0c9e..4f8184d069cb 100644
--- a/Documentation/devicetree/bindings/spi/spi_atmel.txt
+++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt
@@ -5,6 +5,9 @@ Required properties:
 - reg: Address and length of the register set for the device
 - interrupts: Should contain spi interrupt
 - cs-gpios: chipselects
+- clock-names: tuple listing input clock names.
+	Required elements: "spi_clk"
+- clocks: phandles to input clocks.
 
 Example:
 
@@ -14,6 +17,8 @@ spi1: spi@fffcc000 {
 	interrupts = <13 4 5>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	clocks = <&spi1_clk>;
+	clock-names = "spi_clk";
 	cs-gpios = <&pioB 3 0>;
 	status = "okay";
 
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 3f900cd51bf0..40ce2df0e0e9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -8,6 +8,7 @@ ad	Avionic Design GmbH
 adi	Analog Devices, Inc.
 aeroflexgaisler	Aeroflex Gaisler AB
 ak	Asahi Kasei Corp.
+allwinner	Allwinner Technology Co., Ltd.
 altr	Altera Corp.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 amstaos	AMS-Taos Inc.
@@ -40,6 +41,7 @@ gmt	Global Mixed-mode Technology, Inc.
 gumstix	Gumstix, Inc.
 haoyu	Haoyu Microelectronic Co. Ltd.
 hisilicon	Hisilicon Limited.
+honeywell	Honeywell
 hp	Hewlett Packard
 ibm	International Business Machines (IBM)
 idt	Integrated Device Technologies, Inc.
@@ -55,6 +57,7 @@ maxim	Maxim Integrated Products
 microchip	Microchip Technology Inc.
 mosaixtech	Mosaix Technologies, Inc.
 national	National Semiconductor
+neonode		Neonode Inc.
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
@@ -64,7 +67,7 @@ phytec	PHYTEC Messtechnik GmbH
 picochip	Picochip Ltd
 powervr	PowerVR (deprecated, use img)
 qca	Qualcomm Atheros, Inc.
-qcom	Qualcomm, Inc.
+qcom	Qualcomm Technologies, Inc
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 realtek Realtek Semiconductor Corp.
@@ -78,6 +81,7 @@ silabs	Silicon Laboratories
 simtek
 sirf	SiRF Technology, Inc.
 snps 	Synopsys, Inc.
+spansion	Spansion Inc.
 st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson