Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux

Pull thermal management updates from Zhang Rui:

 - Fix a problem where orderly_shutdown() is called for multiple times
   due to multiple critical overheating events raised in a short period
   by platform thermal driver. (Keerthy)

 - Introduce a backup thermal shutdown mechanism, which invokes
   kernel_power_off()/emergency_restart() directly, after
   orderly_shutdown() being issued for certain amount of time(specified
   via Kconfig). This is useful in certain conditions that userspace may
   be unable to power off the system in a clean manner and leaves the
   system in a critical state, like in the middle of driver probing
   phase. (Keerthy)

 - Introduce a new interface in thermal devfreq_cooling code so that the
   driver can provide more precise data regarding actual power to the
   thermal governor every time the power budget is calculated. (Lukasz
   Luba)

 - Introduce BCM 2835 soc thermal driver and northstar thermal driver,
   within a new sub-folder. (Rafał Miłecki)

 - Introduce DA9062/61 thermal driver. (Steve Twiss)

 - Remove non-DT booting on TI-SoC driver. Also add support to fetching
   coefficients from DT. (Keerthy)

 - Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)

 - Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
   Brian Bian)

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
  thermal: core: Add a back up thermal shutdown mechanism
  thermal: core: Allow orderly_poweroff to be called only once
  Thermal: Intel SoC DTS: Change interrupt request behavior
  trace: thermal: add another parameter 'power' to the tracing function
  thermal: devfreq_cooling: add new interface for direct power read
  thermal: devfreq_cooling: refactor code and add get_voltage function
  thermal: mt8173: minor mtk_thermal.c cleanups
  thermal: bcm2835: move to the broadcom subdirectory
  thermal: broadcom: ns: specify myself as MODULE_AUTHOR
  thermal: da9062/61: Thermal junction temperature monitoring driver
  Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
  thermal: broadcom: add Northstar thermal driver
  dt-bindings: thermal: add support for Broadcom's Northstar thermal
  thermal: bcm2835: add thermal driver for bcm2835 SoC
  dt-bindings: Add thermal zone to bcm2835-thermal example
  thermal: rcar_gen3_thermal: add suspend and resume support
  thermal: rcar_gen3_thermal: store device match data in private structure
  thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
  thermal: rcar_gen3_thermal: record and check number of TSCs found
  thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
  ...

3 files changed, 101 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt
index 474531d2b2c5..da8c5b73ad10 100644
--- a/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt
@@ -3,15 +3,39 @@ Binding for Thermal Sensor driver for BCM2835 SoCs.
 Required parameters:
 -------------------
 
-compatible: 	should be one of: "brcm,bcm2835-thermal",
-		"brcm,bcm2836-thermal" or "brcm,bcm2837-thermal"
-reg:		Address range of the thermal registers.
-clocks: 	Phandle of the clock used by the thermal sensor.
+compatible: 		should be one of: "brcm,bcm2835-thermal",
+			"brcm,bcm2836-thermal" or "brcm,bcm2837-thermal"
+reg:			Address range of the thermal registers.
+clocks: 		Phandle of the clock used by the thermal sensor.
+#thermal-sensor-cells:	should be 0 (see thermal.txt)
 
 Example:
 
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive = <0>;
+		polling-delay = <1000>;
+
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <80000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+
+		coefficients = <(-538)	407000>;
+
+		cooling-maps {
+		};
+	};
+};
+
 thermal: thermal@7e212000 {
 	compatible = "brcm,bcm2835-thermal";
 	reg = <0x7e212000 0x8>;
 	clocks = <&clocks BCM2835_CLOCK_TSENS>;
+	#thermal-sensor-cells = <0>;
 };
diff --git a/Documentation/devicetree/bindings/thermal/brcm,ns-thermal b/Documentation/devicetree/bindings/thermal/brcm,ns-thermal
new file mode 100644
index 000000000000..68e047170039
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/brcm,ns-thermal
@@ -0,0 +1,37 @@
+* Broadcom Northstar Thermal
+
+This binding describes thermal sensor that is part of Northstar's DMU (Device
+Management Unit).
+
+Required properties:
+- compatible : Must be "brcm,ns-thermal"
+- reg : iomem address range of PVTMON registers
+- #thermal-sensor-cells : Should be <0>
+
+Example:
+
+thermal: thermal@1800c2c0 {
+	compatible = "brcm,ns-thermal";
+	reg = <0x1800c2c0 0x10>;
+	#thermal-sensor-cells = <0>;
+};
+
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive = <0>;
+		polling-delay = <1000>;
+		coefficients = <(-556) 418000>;
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <125000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+
+		cooling-maps {
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/thermal/da9062-thermal.txt b/Documentation/devicetree/bindings/thermal/da9062-thermal.txt
new file mode 100644
index 000000000000..e241bb5a5584
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/da9062-thermal.txt
@@ -0,0 +1,36 @@
+* Dialog DA9062/61 TJUNC Thermal Module
+
+This module is part of the DA9061/DA9062. For more details about entire
+DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt
+
+Junction temperature thermal module uses an interrupt signal to identify
+high THERMAL_TRIP_HOT temperatures for the PMIC device.
+
+Required properties:
+
+- compatible: should be one of the following valid compatible string lines:
+        "dlg,da9061-thermal", "dlg,da9062-thermal"
+        "dlg,da9062-thermal"
+
+Optional properties:
+
+- polling-delay-passive : Specify the polling period, measured in
+    milliseconds, between thermal zone device update checks.
+
+Example: DA9062
+
+	pmic0: da9062@58 {
+		thermal {
+			compatible = "dlg,da9062-thermal";
+			polling-delay-passive = <3000>;
+		};
+	};
+
+Example: DA9061 using a fall-back compatible for the DA9062 onkey driver
+
+	pmic0: da9061@58 {
+		thermal {
+			compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
+			polling-delay-passive = <3000>;
+		};
+	};