diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2022-08-05 03:08:34 +0200 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2022-08-05 03:08:34 +0200 |
| commit | da8d07af4b3e2e407c5dd13f08b64580931fd1a6 (patch) | |
| tree | 701cabedfc73acbe83447e88616cc129ede7973e /Documentation/devicetree | |
| parent | Merge tag 'for-linus-2022080201' of git://git.kernel.org/pub/scm/linux/kernel... (diff) | |
| parent | dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml (diff) | |
| download | linux-da8d07af4b3e2e407c5dd13f08b64580931fd1a6.tar.xz linux-da8d07af4b3e2e407c5dd13f08b64580931fd1a6.zip | |
Merge tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Add spi-peripheral-props.yaml references to various SPI device
bindings
- Convert qcom,pm8916-wdt, ds1307, Qualcomm BAM DMA, is31fl319x,
skyworks,aat1290, Rockchip EMAC, gpio-ir-receiver, ahci-ceva, Arm
CCN PMU, rda,8810pl-intc, sil,sii9022, ps2-gpio, and
arm-firmware-suite bindings to DT schema format
- New bindings for Arm virtual platforms display, Qualcomm IMEM
memory region, Samsung S5PV210 ChipID, EM Microelectronic EM3027
RTC, and arm,cortex-a78ae
- Add vendor prefixes for asrock, bytedance, hxt, ingrasys, inventec,
quanta, and densitron
- Add missing MSI and IOMMU properties to host-generic-pci
- Remove bindings for removed EFM32 platform
- Remove old chosen.txt binding (replaced by schema)
- Treewide add missing type information for properties
- Treewide fixing of typos and its vs. it's in bindings. Its all good
now.
- Drop unnecessary quoting in power related schemas
- Several LED binding updates which didn't get picked up
- Move various bindings to proper directories
DT core code:
- Convert unittest GPIO related tests to use fwnode
- Check ima-kexec-buffer against memory bounds
- Print reserved-memory allocation/reservation failures as errors
- Cleanup early_init_dt_reserve_memory_arch()
- Simplify of_overlay_fdt_apply() tail"
* tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (65 commits)
dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml
dt-bindings: power: supply: drop quotes when not needed
dt-bindings: power: reset: drop quotes when not needed
dt-bindings: power: drop quotes when not needed
dt-bindings: PCI: host-generic-pci: Allow IOMMU and MSI properties
of/fdt: declared return type does not match actual return type
devicetree/bindings: correct possessive "its" typos
dt-bindings: net: convert emac_rockchip.txt to YAML
dt-bindings: eeprom: microchip,93lc46b: move to eeprom directory
dt-bindings: eeprom: at25: use spi-peripheral-props.yaml
dt-bindings: display: use spi-peripheral-props.yaml
dt-bindings: watchdog: qcom,pm8916-wdt: convert to dtschema
dt-bindings: power: reset: qcom,pon: use absolute path to other schema
dt-bindings: iio/dac: adi,ad5766: Add missing type to 'output-range-microvolts'
dt-bindings: power: supply: charger-manager: Add missing type for 'cm-battery-stat'
dt-bindings: panel: raydium,rm67191: Add missing type to 'video-mode'
of/fdt: Clean up early_init_dt_reserve_memory_arch()
dt-bindings: PCI: fsl,imx6q-pcie: Add missing type for 'reset-gpio-active-high'
dt-bindings: rtc: Add EM Microelectronic EM3027 bindings
dt-bindings: rtc: ds1307: Convert to json-schema
...
Diffstat (limited to 'Documentation/devicetree')
144 files changed, 1792 insertions, 1292 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml index 5c2e3a5f3789..a07c5bac7c46 100644 --- a/Documentation/devicetree/bindings/arm/cpus.yaml +++ b/Documentation/devicetree/bindings/arm/cpus.yaml @@ -138,6 +138,7 @@ properties: - arm,cortex-a76 - arm,cortex-a77 - arm,cortex-a78 + - arm,cortex-a78ae - arm,cortex-a510 - arm,cortex-a710 - arm,cortex-m0 diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt index 94d50a949be1..c0e3c3a42bea 100644 --- a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt +++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt @@ -10,7 +10,7 @@ system, notifying them when a low power state is entered or exited. Multiple revisions of the SAW hardware are supported using these Device Nodes. SAW2 revisions differ in the register offset and configuration data. Also, the same revision of the SAW in different SoCs may have different configuration -data due the the differences in hardware capabilities. Hence the SoC name, the +data due the differences in hardware capabilities. Hence the SoC name, the version of the SAW hardware in that SoC and the distinction between cpu (big or Little) or cache, may be needed to uniquely identify the SAW register configuration and initialization data. The compatible string is used to diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml index 564ae6aaccf7..7fd8d47b1be4 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml @@ -208,7 +208,7 @@ properties: "^[a-z0-9]+$": type: object - patternProperties: + properties: clocks: minItems: 1 maxItems: 8 diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.yaml b/Documentation/devicetree/bindings/arm/vexpress-sysreg.yaml index b5e26e41f88c..f04db802a732 100644 --- a/Documentation/devicetree/bindings/arm/vexpress-sysreg.yaml +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.yaml @@ -29,6 +29,13 @@ properties: ranges: true + gpio-controller: + deprecated: true + + "#gpio-cells": + deprecated: true + const: 2 + additionalProperties: false patternProperties: @@ -67,8 +74,7 @@ patternProperties: required: - compatible - - "#address-cells" - - "#size-cells" + - reg examples: - | diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt b/Documentation/devicetree/bindings/ata/ahci-ceva.txt deleted file mode 100644 index bfb6da0281ec..000000000000 --- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt +++ /dev/null @@ -1,63 +0,0 @@ -Binding for CEVA AHCI SATA Controller - -Required properties: - - reg: Physical base address and size of the controller's register area. - - compatible: Compatibility string. Must be 'ceva,ahci-1v84'. - - clocks: Input clock specifier. Refer to common clock bindings. - - interrupts: Interrupt specifier. Refer to interrupt binding. - - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for port 0. - - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; - CINMP : COMINIT Negate Minimum Period. - CIBGN : COMINIT Burst Gap Nominal. - CIBGMX: COMINIT Burst Gap Maximum. - CIBGMN: COMINIT Burst Gap Minimum. - - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for port 0. - - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; - CWBGMN: COMWAKE Burst Gap Minimum. - CWBGMX: COMWAKE Burst Gap Maximum. - CWBGN: COMWAKE Burst Gap Nominal. - CWNMP: COMWAKE Negate Minimum Period. - - ceva,p0-burst-params: Burst timing value for COM parameter for port 0. - - ceva,p1-burst-params: Burst timing value for COM parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-burst-params = /bits/ 8 <BMX BNM SFD PTST>; - BMX: COM Burst Maximum. - BNM: COM Burst Nominal. - SFD: Signal Failure Detection value. - PTST: Partial to Slumber timer value. - - ceva,p0-retry-params: Retry interval timing value for port 0. - - ceva,p1-retry-params: Retry interval timing value for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-retry-params = /bits/ 16 <RIT RCT>; - RIT: Retry Interval Timer. - RCT: Rate Change Timer. - -Optional properties: - - ceva,broken-gen2: limit to gen1 speed instead of gen2. - - phys: phandle for the PHY device - - resets: phandle to the reset controller for the SATA IP - -Examples: - ahci@fd0c0000 { - compatible = "ceva,ahci-1v84"; - reg = <0xfd0c0000 0x200>; - interrupt-parent = <&gic>; - interrupts = <0 133 4>; - clocks = <&clkc SATA_CLK_ID>; - ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; - ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; - ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; - ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; - - ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; - ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; - ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; - ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; - ceva,broken-gen2; - phys = <&psgtr 1 PHY_TYPE_SATA 1 1>; - resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; - }; diff --git a/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml new file mode 100644 index 000000000000..9b31f864e071 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ceva,ahci-1v84.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ceva AHCI SATA Controller + +maintainers: + - Piyush Mehta <piyush.mehta@xilinx.com> + +description: | + The Ceva SATA controller mostly conforms to the AHCI interface with some + special extensions to add functionality, is a high-performance dual-port + SATA host controller with an AHCI compliant command layer which supports + advanced features such as native command queuing and frame information + structure (FIS) based switching for systems employing port multipliers. + +properties: + compatible: + const: ceva,ahci-1v84 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + dma-coherent: true + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + ceva,p0-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p0-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p0-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p0-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,p1-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p1-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p1-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p1-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 1. + The fields for the above parameter must be as shown below:- + ceva,pN-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,broken-gen2: + $ref: /schemas/types.yaml#/definitions/flag + description: | + limit to gen1 speed instead of gen2. + + phys: + maxItems: 1 + + phy-names: + items: + - const: sata-phy + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - interrupts + - ceva,p0-cominit-params + - ceva,p0-comwake-params + - ceva,p0-burst-params + - ceva,p0-retry-params + - ceva,p1-cominit-params + - ceva,p1-comwake-params + - ceva,p1-burst-params + - ceva,p1-retry-params + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/xlnx-zynqmp-power.h> + #include <dt-bindings/reset/xlnx-zynqmp-resets.h> + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/phy/phy.h> + + sata: ahci@fd0c0000 { + compatible = "ceva,ahci-1v84"; + reg = <0xfd0c0000 0x200>; + interrupt-parent = <&gic>; + interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zynqmp_clk SATA_REF>; + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,broken-gen2; + phys = <&psgtr 1 PHY_TYPE_SATA 1 1>; + resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; + }; diff --git a/Documentation/devicetree/bindings/bus/qcom,ssc-block-bus.yaml b/Documentation/devicetree/bindings/bus/qcom,ssc-block-bus.yaml index 5b9705079015..8e9e6ff35d7d 100644 --- a/Documentation/devicetree/bindings/bus/qcom,ssc-block-bus.yaml +++ b/Documentation/devicetree/bindings/bus/qcom,ssc-block-bus.yaml @@ -28,11 +28,9 @@ properties: - const: qcom,ssc-block-bus reg: - description: | - Shall contain the addresses of the SSCAON_CONFIG0 and SSCAON_CONFIG1 - registers - minItems: 2 - maxItems: 2 + items: + - description: SSCAON_CONFIG0 registers + - description: SSCAON_CONFIG1 registers reg-names: items: @@ -48,7 +46,6 @@ properties: ranges: true clocks: - minItems: 6 maxItems: 6 clock-names: @@ -61,9 +58,9 @@ properties: - const: ssc_ahbs power-domains: - description: Power domain phandles for the ssc_cx and ssc_mx power domains - minItems: 2 - maxItems: 2 + items: + - description: CX power domain + - description: MX power domain power-domain-names: items: @@ -71,11 +68,11 @@ properties: - const: ssc_mx resets: - description: | - Reset phandles for the ssc_reset and ssc_bcr resets (note: ssc_bcr is the - branch control register associated with the ssc_xo and ssc_ahbs clocks) - minItems: 2 - maxItems: 2 + items: + - description: Main reset + - description: + SSC Branch Control Register reset (associated with the ssc_xo and + ssc_ahbs clocks) reset-names: items: diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt deleted file mode 100644 index 1cc3aa10dcb1..000000000000 --- a/Documentation/devicetree/bindings/chosen.txt +++ /dev/null @@ -1,137 +0,0 @@ -The chosen node ---------------- - -The chosen node does not represent a real device, but serves as a place -for passing data between firmware and the operating system, like boot -arguments. Data in the chosen node does not represent the hardware. - -The following properties are recognized: - - -kaslr-seed ------------ - -This property is used when booting with CONFIG_RANDOMIZE_BASE as the -entropy used to randomize the kernel image base address location. Since -it is used directly, this value is intended only for KASLR, and should -not be used for other purposes (as it may leak information about KASLR -offsets). It is parsed as a u64 value, e.g. - -/ { - chosen { - kaslr-seed = <0xfeedbeef 0xc0def00d>; - }; -}; - -Note that if this property is set from UEFI (or a bootloader in EFI -mode) when EFI_RNG_PROTOCOL is supported, it will be overwritten by -the Linux EFI stub (which will populate the property itself, using -EFI_RNG_PROTOCOL). - -stdout-path ------------ - -Device trees may specify the device to be used for boot console output -with a stdout-path property under /chosen, as described in the Devicetree -Specification, e.g. - -/ { - chosen { - stdout-path = "/serial@f00:115200"; - }; - - serial@f00 { - compatible = "vendor,some-uart"; - reg = <0xf00 0x10>; - }; -}; - -If the character ":" is present in the value, this terminates the path. -The meaning of any characters following the ":" is device-specific, and -must be specified in the relevant binding documentation. - -For UART devices, the preferred binding is a string in the form: - - <baud>{<parity>{<bits>{<flow>}}} - -where - - baud - baud rate in decimal - parity - 'n' (none), 'o', (odd) or 'e' (even) - bits - number of data bits - flow - 'r' (rts) - -For example: 115200n8r - -Implementation note: Linux will look for the property "linux,stdout-path" or -on PowerPC "stdout" if "stdout-path" is not found. However, the -"linux,stdout-path" and "stdout" properties are deprecated. New platforms -should only use the "stdout-path" property. - -linux,booted-from-kexec ------------------------ - -This property is set (currently only on PowerPC, and only needed on -book3e) by some versions of kexec-tools to tell the new kernel that it -is being booted by kexec, as the booting environment may differ (e.g. -a different secondary CPU release mechanism) - -linux,usable-memory-range -------------------------- - -This property holds a base address and size, describing a limited region in -which memory may be considered available for use by the kernel. Memory outside -of this range is not available for use. - -This property describes a limitation: memory within this range is only -valid when also described through another mechanism that the kernel -would otherwise use to determine available memory (e.g. memory nodes -or the EFI memory map). Valid memory may be sparse within the range. -e.g. - -/ { - chosen { - linux,usable-memory-range = <0x9 0xf0000000 0x0 0x10000000>; - }; -}; - -The main usage is for crash dump kernel to identify its own usable -memory and exclude, at its boot time, any other memory areas that are -part of the panicked kernel's memory. - -While this property does not represent a real hardware, the address -and the size are expressed in #address-cells and #size-cells, -respectively, of the root node. - -linux,elfcorehdr ----------------- - -This property holds the memory range, the address and the size, of the elf -core header which mainly describes the panicked kernel's memory layout as -PT_LOAD segments of elf format. -e.g. - -/ { - chosen { - linux,elfcorehdr = <0x9 0xfffff000 0x0 0x800>; - }; -}; - -While this property does not represent a real hardware, the address -and the size are expressed in #address-cells and #size-cells, -respectively, of the root node. - -linux,initrd-start and linux,initrd-end ---------------------------------------- - -These properties hold the physical start and end address of an initrd that's -loaded by the bootloader. Note that linux,initrd-start is inclusive, but -linux,initrd-end is exclusive. -e.g. - -/ { - chosen { - linux,initrd-start = <0x82000000>; - linux,initrd-end = <0x82800000>; - }; -}; diff --git a/Documentation/devicetree/bindings/clock/efm32-clock.txt b/Documentation/devicetree/bindings/clock/efm32-clock.txt deleted file mode 100644 index 263d293f6a10..000000000000 --- a/Documentation/devicetree/bindings/clock/efm32-clock.txt +++ /dev/null @@ -1,11 +0,0 @@ -* Clock bindings for Energy Micro efm32 Giant Gecko's Clock Management Unit - -Required properties: -- compatible: Should be "efm32gg,cmu" -- reg: Base address and length of the register set -- interrupts: Interrupt used by the CMU -- #clock-cells: Should be <1> - -The clock consumer should specify the desired clock by having the clock ID in -its "clocks" phandle cell. The header efm32-clk.h contains a list of available -IDs. diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt index 55a18939bddd..c918075405ba 100644 --- a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -78,7 +78,7 @@ Required properties: - #clock-cells : from common clock binding; shall be set to 1 (multiple clock outputs). -- clocks : must be set to the parent's phandle. it's could be output clocks of +- clocks : must be set to the parent's phandle. it could be output clocks of a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) - clock-output-names : List of strings used to name the clock outputs. diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt index 36998e184821..c9894538315b 100644 --- a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -15,7 +15,7 @@ Required properties: - for "ti,da850-pll1", shall be "clksrc" Optional properties: -- ti,clkmode-square-wave: Indicates that the the board is supplying a square +- ti,clkmode-square-wave: Indicates that the board is supplying a square wave input on the OSCIN pin instead of using a crystal oscillator. This property is only valid when compatible = "ti,da850-pll0". diff --git a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt index 21c002d28b9b..68504079f99f 100644 --- a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt +++ b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -6,7 +6,7 @@ functional clock but can be configured to provide different clocks. ATL can maintain a clock averages to some desired frequency based on the bws/aws signals - can compensate the drift between the two ws signal. -In order to provide the support for ATL and it's output clocks (which can be used +In order to provide the support for ATL and its output clocks (which can be used internally within the SoC or external components) two sets of bindings is needed: Clock tree binding: diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml index 0420fa563532..ae515651fc6b 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.yaml +++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml @@ -263,11 +263,11 @@ examples: # Micro-USB connector with HS lines routed via controller (MUIC). - | muic-max77843 { - usb_con1: connector { - compatible = "usb-b-connector"; - label = "micro-USB"; - type = "micro"; - }; + usb_con1: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; }; # USB-C connector attached to CC controller (s2mm005), HS lines routed @@ -275,34 +275,34 @@ examples: # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. - | ccic: s2mm005 { - usb_con2: connector { - compatible = "usb-c-connector"; - label = "USB-C"; + usb_con2: connector { + compatible = "usb-c-connector"; + label = "USB-C"; - ports { - #address-cells = <1>; - #size-cells = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; - port@0 { - reg = <0>; - usb_con_hs: endpoint { - remote-endpoint = <&max77865_usbc_hs>; - }; - }; - port@1 { - reg = <1>; - usb_con_ss: endpoint { - remote-endpoint = <&usbdrd_phy_ss>; - }; - }; - port@2 { - reg = <2>; - usb_con_sbu: endpoint { - remote-endpoint = <&dp_aux>; + port@0 { + reg = <0>; + usb_con_hs: endpoint { + remote-endpoint = <&max77865_usbc_hs>; + }; + }; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&dp_aux>; + }; + }; }; - }; }; - }; }; # USB-C connector attached to a typec port controller(ptn5110), which has @@ -310,16 +310,16 @@ examples: - | #include <dt-bindings/usb/pd.h> typec: ptn5110 { - usb_con3: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - power-role = "dual"; - try-power-role = "sink"; - source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; - sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) - PDO_VAR(5000, 12000, 2000)>; - op-sink-microwatt = <10000000>; - }; + usb_con3: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + }; }; # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220) @@ -332,20 +332,20 @@ examples: data-role = "dual"; ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - hs_ep: endpoint { - remote-endpoint = <&usb3_hs_ep>; - }; + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + hs_ep: endpoint { + remote-endpoint = <&usb3_hs_ep>; }; - port@1 { - reg = <1>; - ss_ep: endpoint { - remote-endpoint = <&hd3ss3220_in_ep>; - }; + }; + port@1 { + reg = <1>; + ss_ep: endpoint { + remote-endpoint = <&hd3ss3220_in_ep>; }; + }; }; }; @@ -354,12 +354,12 @@ examples: #include <dt-bindings/gpio/gpio.h> usb { - connector { - compatible = "gpio-usb-b-connector", "usb-b-connector"; - type = "micro"; - id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; - vbus-supply = <&usb_p0_vbus>; - }; + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + vbus-supply = <&usb_p0_vbus>; + }; }; # Micro-USB connector with HS lines routed via controller (MUIC) and MHL @@ -367,27 +367,27 @@ examples: # mobile phone - | muic-max77843 { - usb_con4: connector { - compatible = "samsung,usb-connector-11pin", "usb-b-connector"; - label = "micro-USB"; - type = "micro"; + usb_con4: connector { + compatible = "samsung,usb-connector-11pin", "usb-b-connector"; + label = "micro-USB"; + type = "micro"; - ports { - #address-cells = <1>; - #size-cells = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; - port@0 { - reg = <0>; - muic_to_usb: endpoint { - remote-endpoint = <&usb_to_muic>; - }; - }; - port@3 { - reg = <3>; - usb_con_mhl: endpoint { - remote-endpoint = <&sii8620_mhl>; + port@0 { + reg = <0>; + muic_to_usb: endpoint { + remote-endpoint = <&usb_to_muic>; + }; + }; + port@3 { + reg = <3>; + usb_con_mhl: endpoint { + remote-endpoint = <&sii8620_mhl>; + }; + }; }; - }; }; - }; }; diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.yaml b/Documentation/devicetree/bindings/display/arm,pl11x.yaml index b545c6d20325..6cc9045e5c68 100644 --- a/Documentation/devicetree/bindings/display/arm,pl11x.yaml +++ b/Documentation/devicetree/bindings/display/arm,pl11x.yaml @@ -159,25 +159,12 @@ examples: }; panel { - compatible = "arm,rtsm-display", "panel-dpi"; - power-supply = <&vcc_supply>; + compatible = "arm,rtsm-display"; port { clcd_panel: endpoint { remote-endpoint = <&clcd_pads>; }; }; - - panel-timing { - clock-frequency = <25175000>; - hactive = <640>; - hback-porch = <40>; - hfront-porch = <24>; - hsync-len = <96>; - vactive = <480>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <2>; - }; }; ... diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt deleted file mode 100644 index 3bc760cc31cb..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt +++ /dev/null @@ -1,78 +0,0 @@ -sii902x HDMI bridge bindings - -Required properties: - - compatible: "sil,sii9022" - - reg: i2c address of the bridge - -Optional properties: - - interrupts: describe the interrupt line used to inform the host - about hotplug events. - - reset-gpios: OF device-tree gpio specification for RST_N pin. - - iovcc-supply: I/O Supply Voltage (1.8V or 3.3V) - - cvcc12-supply: Digital Core Supply Voltage (1.2V) - - HDMI audio properties: - - #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin - is wired, <1> if the both are wired. HDMI audio is - configured only if this property is found. - - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3 - Each integer indicates which i2s pin is connected to which - audio fifo. The first integer selects i2s audio pin for the - first audio fifo#0 (HDMI channels 1&2), second for fifo#1 - (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s - pins (SD0 - SD3). Any i2s pin can be connected to any fifo, - but there can be no gaps. E.g. an i2s pin must be mapped to - fifo#0 and fifo#1 before mapping a channel to fifo#2. Default - value is <0>, describing SD0 pin beiging routed to hdmi audio - fifo #0. - - clocks: phandle and clock specifier for each clock listed in - the clock-names property - - clock-names: "mclk" - Describes SII902x MCLK input. MCLK can be used to produce - HDMI audio CTS values. This property follows - Documentation/devicetree/bindings/clock/clock-bindings.txt - consumer binding. - - If HDMI audio is configured the sii902x device becomes an I2S - and/or spdif audio codec component (e.g a digital audio sink), - that can be used in configuring a full audio devices with - simple-card or audio-graph-card binding. See their binding - documents on how to describe the way the sii902x device is - connected to the rest of the audio system: - Documentation/devicetree/bindings/sound/simple-card.yaml - Documentation/devicetree/bindings/sound/audio-graph-card.yaml - Note: In case of the audio-graph-card binding the used port - index should be 3. - -Optional subnodes: - - video input: this subnode can contain a video input port node - to connect the bridge to a display controller output (See this - documentation [1]). - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - hdmi-bridge@39 { - compatible = "sil,sii9022"; - reg = <0x39>; - reset-gpios = <&pioA 1 0>; - iovcc-supply = <&v3v3_hdmi>; - cvcc12-supply = <&v1v2_hdmi>; - - #sound-dai-cells = <0>; - sil,i2s-data-lanes = < 0 1 2 >; - clocks = <&mclk>; - clock-names = "mclk"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - bridge_in: endpoint { - remote-endpoint = <&dc_out>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml b/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml new file mode 100644 index 000000000000..5a69547ad3d7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml @@ -0,0 +1,131 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/sil,sii9022.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Image sii902x HDMI bridge + +maintainers: + - Boris Brezillon <bbrezillon@kernel.org> + +properties: + compatible: + oneOf: + - items: + - enum: + - sil,sii9022-cpi # CEC Programming Interface + - sil,sii9022-tpi # Transmitter Programming Interface + - const: sil,sii9022 + - const: sil,sii9022 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: Interrupt line used to inform the host about hotplug events. + + reset-gpios: + maxItems: 1 + + iovcc-supply: + description: I/O Supply Voltage (1.8V or 3.3V) + + cvcc12-supply: + description: Digital Core Supply Voltage (1.2V) + + '#sound-dai-cells': + enum: [ 0, 1 ] + description: | + <0> if only I2S or S/PDIF pin is wired, + <1> if both are wired. + HDMI audio is configured only if this property is found. + If HDMI audio is configured, the sii902x device becomes an I2S and/or + S/PDIF audio codec component (e.g. a digital audio sink), that can be + used in configuring full audio devices with simple-card or + audio-graph-card bindings. See their binding documents on how to describe + the way the + sii902x device is connected to the rest of the audio system: + Documentation/devicetree/bindings/sound/simple-card.yaml + Documentation/devicetree/bindings/sound/audio-graph-card.yaml + Note: In case of the audio-graph-card binding the used port index should + be 3. + + sil,i2s-data-lanes: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + uniqueItems: true + items: + enum: [ 0, 1, 2, 3 ] + description: + Each integer indicates which I2S pin is connected to which audio FIFO. + The first integer selects the I2S audio pin for the first audio FIFO#0 + (HDMI channels 1&2), the second for FIFO#1 (HDMI channels 3&4), and so + on. There are 4 FIFOs and 4 I2S pins (SD0 - SD3). Any I2S pin can be + connected to any FIFO, but there can be no gaps. E.g. an I2S pin must be + mapped to FIFO#0 and FIFO#1 before mapping a channel to FIFO#2. The + default value is <0>, describing SD0 pin being routed to HDMI audio + FIFO#0. + + clocks: + maxItems: 1 + description: MCLK input. MCLK can be used to produce HDMI audio CTS values. + + clock-names: + const: mclk + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Parallel RGB input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: HDMI output port + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: Sound input port + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi-bridge@39 { + compatible = "sil,sii9022"; + reg = <0x39>; + reset-gpios = <&pioA 1 0>; + iovcc-supply = <&v3v3_hdmi>; + cvcc12-supply = <&v1v2_hdmi>; + + #sound-dai-cells = <0>; + sil,i2s-data-lanes = < 0 1 2 >; + clocks = <&mclk>; + clock-names = "mclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dc_out>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/arm,rtsm-display.yaml b/Documentation/devicetree/bindings/display/panel/arm,rtsm-display.yaml new file mode 100644 index 000000000000..4ad484f09ba3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/arm,rtsm-display.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/arm,rtsm-display.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Arm RTSM Virtual Platforms Display + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: arm,rtsm-display + + port: true + +required: + - compatible + - port + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml b/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml index b4314ce7b411..ee357e139ac0 100644 --- a/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml +++ b/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml @@ -15,13 +15,13 @@ maintainers: allOf: - $ref: panel-common.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: compatible: const: lg,lg4573 reg: true - spi-max-frequency: true required: - compatible diff --git a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml index 617aa8c8c03a..d62fd692bf10 100644 --- a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml +++ b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml @@ -38,6 +38,7 @@ properties: 0 - burst-mode 1 - non-burst with sync event 2 - non-burst with sync pulse + $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1, 2] required: diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml b/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml index 157b1a7b18f9..53f181ef3670 100644 --- a/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml +++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.yaml @@ -15,6 +15,7 @@ description: allOf: - $ref: panel/panel-common.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/display/solomon,ssd1307fb.yaml b/Documentation/devicetree/bindings/display/solomon,ssd1307fb.yaml index 3fbd87c2c120..669f70b1b4c4 100644 --- a/Documentation/devicetree/bindings/display/solomon,ssd1307fb.yaml +++ b/Documentation/devicetree/bindings/display/solomon,ssd1307fb.yaml @@ -49,9 +49,6 @@ properties: vbat-supply: description: The supply for VBAT - # Only required for SPI - spi-max-frequency: true - solomon,height: $ref: /schemas/types.yaml#/definitions/uint32 default: 16 @@ -153,6 +150,8 @@ required: - reg allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: properties: compatible: @@ -223,7 +222,7 @@ allOf: solomon,dclk-frq: default: 10 -additionalProperties: false +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/dma/qcom,bam-dma.yaml b/Documentation/devicetree/bindings/dma/qcom,bam-dma.yaml new file mode 100644 index 000000000000..9bf3a1b164f1 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom,bam-dma.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/qcom,bam-dma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies Inc BAM DMA controller + +maintainers: + - Andy Gross <agross@kernel.org> + - Bjorn Andersson <bjorn.andersson@linaro.org> + +allOf: + - $ref: "dma-controller.yaml#" + +properties: + compatible: + enum: + # APQ8064, IPQ8064 and MSM8960 + - qcom,bam-v1.3.0 + # MSM8974, APQ8074 and APQ8084 + - qcom,bam-v1.4.0 + # MSM8916 + - qcom,bam-v1.7.0 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: bam_clk + + "#dma-cells": + const: 1 + + interrupts: + maxItems: 1 + + iommus: + minItems: 1 + maxItems: 4 + + num-channels: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Indicates supported number of DMA channels in a remotely controlled bam. + + qcom,controlled-remotely: + type: boolean + description: + Indicates that the bam is controlled by remote proccessor i.e. execution + environment. + + qcom,ee: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: + Indicates the active Execution Environment identifier (0-7) used in the + secure world. + + qcom,num-ees: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Indicates supported number of Execution Environments in a remotely + controlled bam. + + qcom,powered-remotely: + type: boolean + description: + Indicates that the bam is powered up by a remote processor but must be + initialized by the local processor. + + reg: + maxItems: 1 + +required: + - compatible + - "#dma-cells" + - interrupts + - qcom,ee + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-msm8974.h> + + dma-controller@f9944000 { + compatible = "qcom,bam-v1.4.0"; + reg = <0xf9944000 0x15000>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt deleted file mode 100644 index 6e9a5497b3f2..000000000000 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ /dev/null @@ -1,52 +0,0 @@ -QCOM BAM DMA controller - -Required properties: -- compatible: must be one of the following: - * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084 - * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960 - * "qcom,bam-v1.7.0" for MSM8916 -- reg: Address range for DMA registers -- interrupts: Should contain the one interrupt shared by all channels -- #dma-cells: must be <1>, the cell in the dmas property of the client device - represents the channel number -- clocks: required clock -- clock-names: must contain "bam_clk" entry -- qcom,ee : indicates the active Execution Environment identifier (0-7) used in - the secure world. -- qcom,controlled-remotely : optional, indicates that the bam is controlled by - remote proccessor i.e. execution environment. -- qcom,powered-remotely : optional, indicates that the bam is powered up by - a remote processor but must be initialized by the local processor. -- num-channels : optional, indicates supported number of DMA channels in a - remotely controlled bam. -- qcom,num-ees : optional, indicates supported number of Execution Environments - in a remotely controlled bam. - -Example: - - uart-bam: dma@f9984000 = { - compatible = "qcom,bam-v1.4.0"; - reg = <0xf9984000 0x15000>; - interrupts = <0 94 0>; - clocks = <&gcc GCC_BAM_DMA_AHB_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - -DMA clients must use the format described in the dma.txt file, using a two cell -specifier for each channel. - -Example: - serial@f991e000 { - compatible = "qcom,msm-uart"; - reg = <0xf991e000 0x1000> - <0xf9944000 0x19000>; - interrupts = <0 108 0>; - clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; - - dmas = <&uart-bam 0>, <&uart-bam 1>; - dma-names = "rx", "tx"; - }; diff --git a/Documentation/devicetree/bindings/eeprom/at25.yaml b/Documentation/devicetree/bindings/eeprom/at25.yaml index fbf99e346966..8b1c997caac1 100644 --- a/Documentation/devicetree/bindings/eeprom/at25.yaml +++ b/Documentation/devicetree/bindings/eeprom/at25.yaml @@ -44,8 +44,6 @@ properties: reg: maxItems: 1 - spi-max-frequency: true - pagesize: $ref: /schemas/types.yaml#/definitions/uint32 enum: [1, 8, 16, 32, 64, 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768, 65536, 131072] @@ -105,6 +103,7 @@ required: - spi-max-frequency allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# - if: properties: compatible: @@ -117,7 +116,7 @@ allOf: - size - address-width -additionalProperties: false +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/misc/eeprom-93xx46.yaml b/Documentation/devicetree/bindings/eeprom/microchip,93lc46b.yaml index 44fd2f6f0d8a..0c2f5ddb79c5 100644 --- a/Documentation/devicetree/bindings/misc/eeprom-93xx46.yaml +++ b/Documentation/devicetree/bindings/eeprom/microchip,93lc46b.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/misc/eeprom-93xx46.yaml# +$id: http://devicetree.org/schemas/eeprom/microchip,93lc46b.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Microchip 93xx46 SPI compatible EEPROM family dt bindings @@ -28,9 +28,6 @@ properties: description: chip select of EEPROM maxItems: 1 - spi-max-frequency: true - spi-cs-high: true - read-only: description: parameter-less property which disables writes to the EEPROM @@ -42,14 +39,16 @@ properties: of EEPROM (e.g. for SPI bus multiplexing) maxItems: 1 - required: - compatible - reg - data-size - spi-max-frequency -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/fpga/fpga-region.txt b/Documentation/devicetree/bindings/fpga/fpga-region.txt index 7d3515264838..6694ef29a267 100644 --- a/Documentation/devicetree/bindings/fpga/fpga-region.txt +++ b/Documentation/devicetree/bindings/fpga/fpga-region.txt @@ -330,7 +330,7 @@ succeeded. The Device Tree Overlay will contain: * "target-path" or "target" - The insertion point where the the contents of the overlay will go into the + The insertion point where the contents of the overlay will go into the live tree. target-path is a full path, while target is a phandle. * "ranges" The address space mapping from processor to FPGA bus(ses). diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt index 414a01cdf715..fba3c61f6a5b 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt @@ -14,7 +14,7 @@ Optional properties: - ngpios : Number of used GPIO lines (0..n-1), default is 8. - load-gpios : GPIO pin specifier attached to load enable, this pin is pulsed before reading from the device to - load input pin values into the the device. + load input pin values into the device. For other required and optional properties of SPI slave nodes please refer to ../spi/spi-bus.txt. diff --git a/Documentation/devicetree/bindings/soc/samsung/exynos-chipid.yaml b/Documentation/devicetree/bindings/hwinfo/samsung,exynos-chipid.yaml index 4bb8efb83ac1..95cbdcb56efe 100644 --- a/Documentation/devicetree/bindings/soc/samsung/exynos-chipid.yaml +++ b/Documentation/devicetree/bindings/hwinfo/samsung,exynos-chipid.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: http://devicetree.org/schemas/soc/samsung/exynos-chipid.yaml# +$id: http://devicetree.org/schemas/hwinfo/samsung,exynos-chipid.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Samsung Exynos SoC series Chipid driver diff --git a/Documentation/devicetree/bindings/hwinfo/samsung,s5pv210-chipid.yaml b/Documentation/devicetree/bindings/hwinfo/samsung,s5pv210-chipid.yaml new file mode 100644 index 000000000000..563ded4fca83 --- /dev/null +++ b/Documentation/devicetree/bindings/hwinfo/samsung,s5pv210-chipid.yaml @@ -0,0 +1,30 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwinfo/samsung,s5pv210-chipid.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5PV210 SoC ChipID + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: samsung,s5pv210-chipid + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + chipid@e0000000 { + compatible = "samsung,s5pv210-chipid"; + reg = <0xe0000000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/soc/ti/k3-socinfo.yaml b/Documentation/devicetree/bindings/hwinfo/ti,k3-socinfo.yaml index a1a8423b2e2e..dada28b47ea0 100644 --- a/Documentation/devicetree/bindings/soc/ti/k3-socinfo.yaml +++ b/Documentation/devicetree/bindings/hwinfo/ti,k3-socinfo.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/soc/ti/k3-socinfo.yaml# +$id: http://devicetree.org/schemas/hwinfo/ti,k3-socinfo.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments K3 Multicore SoC platforms chipid module diff --git a/Documentation/devicetree/bindings/hwmon/adt7475.yaml b/Documentation/devicetree/bindings/hwmon/adt7475.yaml index 56baf2e5c6d1..ea595102a86e 100644 --- a/Documentation/devicetree/bindings/hwmon/adt7475.yaml +++ b/Documentation/devicetree/bindings/hwmon/adt7475.yaml @@ -57,7 +57,7 @@ patternProperties: Configures bypassing the individual voltage input attenuator. If set to 1 the attenuator is bypassed if set to 0 the attenuator is not bypassed. If the property is absent then the attenuator - retains it's configuration from the bios/bootloader. + retains its configuration from the bios/bootloader. $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1] diff --git a/Documentation/devicetree/bindings/i2c/ibm,p8-occ-hwmon.txt b/Documentation/devicetree/bindings/hwmon/ibm,p8-occ-hwmon.txt index 5dc5d2e2573d..5dc5d2e2573d 100644 --- a/Documentation/devicetree/bindings/i2c/ibm,p8-occ-hwmon.txt +++ b/Documentation/devicetree/bindings/hwmon/ibm,p8-occ-hwmon.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt deleted file mode 100644 index 3b30e54ae3c7..000000000000 --- a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Energymicro efm32 i2c controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : should be "energymicro,efm32-i2c" - - interrupts : the interrupt number - - clocks : reference to the module clock - -Recommended properties : - - - clock-frequency : maximal I2C bus clock frequency in Hz. - - energymicro,location : Decides the location of the USART I/O pins. - Allowed range : [0 .. 6] - -Example: - i2c0: i2c@4000a000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "energymicro,efm32-i2c"; - reg = <0x4000a000 0x400>; - interrupts = <9>; - clocks = <&cmu clk_HFPERCLKI2C0>; - clock-frequency = <100000>; - energymicro,location = <3>; - - eeprom@50 { - compatible = "microchip,24c02"; - reg = <0x50>; - pagesize = <16>; - }; - }; - diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml index a8f7720d1e3e..29bd16dab546 100644 --- a/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml @@ -22,6 +22,8 @@ properties: - adi,ad5767 output-range-microvolts: + $ref: /schemas/types.yaml#/definitions/int32-array + maxItems: 2 description: Select converter output range. reg: diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt index 5eef5e7d6aae..c9f2c9f578e3 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt @@ -6,7 +6,7 @@ Required properties: - interrupts : interrupt specification for the ektf2127 interrupt - power-gpios : GPIO specification for the pin connected to the ektf2127's wake input. This needs to be driven high - to take ektf2127 out of it's low power state + to take ektf2127 out of its low power state For additional optional properties see: touchscreen.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt deleted file mode 100644 index e0062aebf025..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt +++ /dev/null @@ -1,61 +0,0 @@ -RDA Micro RDA8810PL Interrupt Controller - -The interrupt controller in RDA8810PL SoC is a custom interrupt controller -which supports up to 32 interrupts. - -Required properties: - -- compatible: Should be "rda,8810pl-intc". -- reg: Specifies base physical address of the registers set. -- interrupt-controller: Identifies the node as an interrupt controller. -- #interrupt-cells: Specifies the number of cells needed to encode an - interrupt source. The value shall be 2. - -The interrupt sources are as follows: - -ID Name ------------- -0: PULSE_DUMMY -1: I2C -2: NAND_NFSC -3: SDMMC1 -4: SDMMC2 -5: SDMMC3 -6: SPI1 -7: SPI2 -8: SPI3 -9: UART1 -10: UART2 -11: UART3 -12: GPIO1 -13: GPIO2 -14: GPIO3 -15: KEYPAD -16: TIMER -17: TIMEROS -18: COMREG0 -19: COMREG1 -20: USB -21: DMC -22: DMA -23: CAMERA -24: GOUDA -25: GPU -26: VPU_JPG -27: VPU_HOST -28: VOC -29: AUIFC0 -30: AUIFC1 -31: L2CC - -Example: - apb@20800000 { - compatible = "simple-bus"; - ... - intc: interrupt-controller@0 { - compatible = "rda,8810pl-intc"; - reg = <0x0 0x1000>; - interrupt-controller; - #interrupt-cells = <2>; - }; - }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.yaml b/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.yaml new file mode 100644 index 000000000000..96d6285d0087 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/rda,8810pl-intc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro RDA8810PL interrupt controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +allOf: + - $ref: /schemas/interrupt-controller.yaml# + +properties: + compatible: + const: rda,8810pl-intc + + reg: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + +required: + - compatible + - reg + - interrupt-controller + - '#interrupt-cells' + +additionalProperties: false + +examples: + - | + intc: interrupt-controller@0 { + compatible = "rda,8810pl-intc"; + reg = <0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + }; +... diff --git a/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml new file mode 100644 index 000000000000..940333f2d69c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml @@ -0,0 +1,193 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/issi,is31fl319x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ISSI LED controllers bindings for IS31FL319{0,1,3,6,9} + +maintainers: + - Vincent Knecht <vincent.knecht@mailoo.org> + +description: | + The IS31FL319X are LED controllers with I2C interface. + Previously known as Si-En SN319{0,1,3,6,9}. + + For more product information please see the links below: + https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf + https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf + https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf + https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf + https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf + +properties: + compatible: + enum: + - issi,is31fl3190 + - issi,is31fl3191 + - issi,is31fl3193 + - issi,is31fl3196 + - issi,is31fl3199 + - si-en,sn3190 + - si-en,sn3191 + - si-en,sn3193 + - si-en,sn3196 + - si-en,sn3199 + + reg: + maxItems: 1 + + shutdown-gpios: + maxItems: 1 + description: GPIO attached to the SDB pin. + + audio-gain-db: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + description: Audio gain selection for external analog modulation input. + enum: [0, 3, 6, 9, 12, 15, 18, 21] + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^led@[1-9]$": + type: object + $ref: common.yaml# + + properties: + reg: + description: Index of the LED. + minimum: 1 + maximum: 9 + + led-max-microamp: + description: + Note that a driver will take the lowest of all LED limits + since the chip has a single global setting. The lowest value + will be chosen due to the PWM specificity, where lower + brightness is achieved by reducing the duty-cycle of pulses + and not the current, which will always have its peak value + equal to led-max-microamp. + +allOf: + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3190 + - issi,is31fl3191 + - issi,is31fl3193 + - si-en,sn3190 + - si-en,sn3191 + - si-en,sn3193 + then: + properties: + reg: + enum: [0x68, 0x69, 0x6a, 0x6b] + + audio-gain-db: false + + patternProperties: + "^led@[1-9]$": + properties: + led-max-microamp: + default: 42000 + enum: [5000, 10000, 17500, 30000, 42000] + else: + properties: + reg: + enum: [0x64, 0x65, 0x66, 0x67] + + patternProperties: + "^led@[1-9]$": + properties: + led-max-microamp: + default: 20000 + enum: [5000, 10000, 15000, 20000, 25000, 30000, 35000, 40000] + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3190 + - issi,is31fl3191 + - si-en,sn3190 + - si-en,sn3191 + then: + patternProperties: + "^led@[1-9]$": + properties: + reg: + maximum: 1 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3193 + - si-en,sn3193 + then: + patternProperties: + "^led@[1-9]$": + properties: + reg: + maximum: 3 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3196 + - si-en,sn3196 + then: + patternProperties: + "^led@[1-9]$": + properties: + reg: + maximum: 6 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@65 { + compatible = "issi,is31fl3196"; + reg = <0x65>; + #address-cells = <1>; + #size-cells = <0>; + + shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + + led@1 { + reg = <1>; + label = "red:aux"; + led-max-microamp = <10000>; + }; + + led@5 { + reg = <5>; + label = "green:power"; + linux,default-trigger = "default-on"; + }; + }; + }; +... + diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt deleted file mode 100644 index 62ed17ec075b..000000000000 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ /dev/null @@ -1,77 +0,0 @@ -* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs - -The device is controlled through two pins: FL_EN and EN_SET. The pins when, -asserted high, enable flash strobe and movie mode (max 1/2 of flash current) -respectively. In order to add a capability of selecting the strobe signal source -(e.g. CPU or camera sensor) there is an additional switch required, independent -of the flash chip. The switch is controlled with pin control. - -Required properties: - -- compatible : Must be "skyworks,aat1290". -- flen-gpios : Must be device tree identifier of the flash device FL_EN pin. -- enset-gpios : Must be device tree identifier of the flash device EN_SET pin. - -Optional properties: -- pinctrl-names : Must contain entries: "default", "host", "isp". Entries - "default" and "host" must refer to the same pin configuration - node, which sets the host as a strobe signal provider. Entry - "isp" must refer to the pin configuration node, which sets the - ISP as a strobe signal provider. - -A discrete LED element connected to the device must be represented by a child -node - see Documentation/devicetree/bindings/leds/common.txt. - -Required properties of the LED child node: -- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt -- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt - Maximum flash LED supply current can be calculated using - following formula: I = 1A * 162kohm / Rset. -- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt - Maximum flash timeout can be calculated using following - formula: T = 8.82 * 10^9 * Ct. - -Optional properties of the LED child node: -- function : see Documentation/devicetree/bindings/leds/common.txt -- color : see Documentation/devicetree/bindings/leds/common.txt -- label : see Documentation/devicetree/bindings/leds/common.txt (deprecated) - -Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with -a switch that allows for routing strobe signal either from the host or from -the camera sensor): - -#include "exynos4412.dtsi" -#include <dt-bindings/leds/common.h> - -led-controller { - compatible = "skyworks,aat1290"; - flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; - enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; - - pinctrl-names = "default", "host", "isp"; - pinctrl-0 = <&camera_flash_host>; - pinctrl-1 = <&camera_flash_host>; - pinctrl-2 = <&camera_flash_isp>; - - camera_flash: led { - function = LED_FUNCTION_FLASH; - color = <LED_COLOR_ID_WHITE>; - led-max-microamp = <520833>; - flash-max-microamp = <1012500>; - flash-max-timeout-us = <1940000>; - }; -}; - -&pinctrl_0 { - camera_flash_host: camera-flash-host { - samsung,pins = "gpj1-0"; - samsung,pin-function = <1>; - samsung,pin-val = <0>; - }; - - camera_flash_isp: camera-flash-isp { - samsung,pins = "gpj1-0"; - samsung,pin-function = <1>; - samsung,pin-val = <1>; - }; -}; diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt deleted file mode 100644 index 676d43ec8169..000000000000 --- a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt +++ /dev/null @@ -1,61 +0,0 @@ -LEDs connected to is31fl319x LED controller chip - -Required properties: -- compatible : Should be any of - "issi,is31fl3190" - "issi,is31fl3191" - "issi,is31fl3193" - "issi,is31fl3196" - "issi,is31fl3199" - "si-en,sn3199". -- #address-cells: Must be 1. -- #size-cells: Must be 0. -- reg: 0x64, 0x65, 0x66, or 0x67. - -Optional properties: -- audio-gain-db : audio gain selection for external analog modulation input. - Valid values: 0 - 21, step by 3 (rounded down) - Default: 0 -- shutdown-gpios : Specifier of the GPIO connected to SDB pin of the chip. - -Each led is represented as a sub-node of the issi,is31fl319x device. -There can be less leds subnodes than the chip can support but not more. - -Required led sub-node properties: -- reg : number of LED line - Valid values: 1 - number of leds supported by the chip variant. - -Optional led sub-node properties: -- label : see Documentation/devicetree/bindings/leds/common.txt. -- linux,default-trigger : - see Documentation/devicetree/bindings/leds/common.txt. -- led-max-microamp : (optional) - Valid values: 5000 - 40000, step by 5000 (rounded down) - Default: 20000 (20 mA) - Note: a driver will take the lowest of all led limits since the - chip has a single global setting. The lowest value will be chosen - due to the PWM specificity, where lower brightness is achieved - by reducing the dury-cycle of pulses and not the current, which - will always have its peak value equal to led-max-microamp. - -Examples: - -fancy_leds: leds@65 { - compatible = "issi,is31fl3196"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x65>; - shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - - red_aux: led@1 { - label = "red:aux"; - reg = <1>; - led-max-microamp = <10000>; - }; - - green_power: led@5 { - label = "green:power"; - reg = <5>; - linux,default-trigger = "default-on"; - }; -}; diff --git a/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml index f12fe5b53f30..d11898567313 100644 --- a/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml +++ b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml @@ -78,60 +78,66 @@ additionalProperties: false examples: - | - #include <dt-bindings/gpio/gpio.h> - #include <dt-bindings/leds/common.h> - - i2c { - #address-cells = <1>; - #size-cells = <0>; - - led-controller@14 { - compatible = "ti,lp5009"; - reg = <0x14>; - #address-cells = <1>; - #size-cells = <0>; - enable-gpios = <&gpio1 16>; - - multi-led@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x1>; - color = <LED_COLOR_ID_RGB>; - function = LED_FUNCTION_CHARGING; - - led-0 { - color = <LED_COLOR_ID_RED>; - }; - - led-1 { - color = <LED_COLOR_ID_GREEN>; - }; - - led-2 { - color = <LED_COLOR_ID_BLUE>; - }; - }; - - multi-led@2 { - #address-cells = <1>; - #size-cells = <2>; - reg = <0x2 0x3 0x5>; - color = <LED_COLOR_ID_RGB>; - function = LED_FUNCTION_STANDBY; + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> - led-6 { - color = <LED_COLOR_ID_RED>; - }; + i2c { + #address-cells = <1>; + #size-cells = <0>; - led-7 { - color = <LED_COLOR_ID_GREEN>; + led-controller@14 { + compatible = "ti,lp5009"; + reg = <0x14>; + #address-cells = <1>; + #size-cells = <0>; + enable-gpios = <&gpio1 16>; + + multi-led@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_CHARGING; + + led@0 { + reg = <0x0>; + color = <LED_COLOR_ID_RED>; + }; + + led@1 { + reg = <0x1>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@2 { + reg = <0x2>; + color = <LED_COLOR_ID_BLUE>; + }; }; - led-8 { - color = <LED_COLOR_ID_BLUE>; + multi-led@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>, <0x4>, <0x5>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STANDBY; + + led@3 { + reg = <0x3>; + color = <LED_COLOR_ID_RED>; + }; + + led@4 { + reg = <0x4>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@5 { + reg = <0x5>; + color = <LED_COLOR_ID_BLUE>; + }; }; - }; - }; + }; }; ... diff --git a/Documentation/devicetree/bindings/leds/leds-lp55xx.yaml b/Documentation/devicetree/bindings/leds/leds-lp55xx.yaml index f552cd143d5b..7ec676e53851 100644 --- a/Documentation/devicetree/bindings/leds/leds-lp55xx.yaml +++ b/Documentation/devicetree/bindings/leds/leds-lp55xx.yaml @@ -108,119 +108,119 @@ additionalProperties: false examples: - | - #include <dt-bindings/leds/common.h> - - i2c { - #address-cells = <1>; - #size-cells = <0>; - - led-controller@32 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,lp8501"; - reg = <0x32>; - clock-mode = /bits/ 8 <2>; - pwr-sel = /bits/ 8 <3>; /* D1~9 connected to VOUT */ - - led@0 { - reg = <0>; - chan-name = "d1"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@1 { - reg = <1>; - chan-name = "d2"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@2 { - reg = <2>; - chan-name = "d3"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@3 { - reg = <3>; - chan-name = "d4"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@4 { - reg = <4>; - chan-name = "d5"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@5 { - reg = <5>; - chan-name = "d6"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@6 { - reg = <6>; - chan-name = "d7"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@7 { - reg = <7>; - chan-name = "d8"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; - - led@8 { - reg = <8>; - chan-name = "d9"; - led-cur = /bits/ 8 <0x14>; - max-cur = /bits/ 8 <0x20>; - }; + #include <dt-bindings/leds/common.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@32 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lp8501"; + reg = <0x32>; + clock-mode = /bits/ 8 <2>; + pwr-sel = /bits/ 8 <3>; /* D1~9 connected to VOUT */ + + led@0 { + reg = <0>; + chan-name = "d1"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@1 { + reg = <1>; + chan-name = "d2"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@2 { + reg = <2>; + chan-name = "d3"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@3 { + reg = <3>; + chan-name = "d4"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@4 { + reg = <4>; + chan-name = "d5"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@5 { + reg = <5>; + chan-name = "d6"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@6 { + reg = <6>; + chan-name = "d7"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@7 { + reg = <7>; + chan-name = "d8"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + led@8 { + reg = <8>; + chan-name = "d9"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; }; - led-controller@33 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "national,lp5523"; - reg = <0x33>; - clock-mode = /bits/ 8 <0>; - - multi-led@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x2>; - color = <LED_COLOR_ID_RGB>; - function = LED_FUNCTION_STANDBY; - linux,default-trigger = "heartbeat"; - - led@0 { - led-cur = /bits/ 8 <50>; - max-cur = /bits/ 8 <100>; - reg = <0x0>; - color = <LED_COLOR_ID_GREEN>; - }; - - led@1 { - led-cur = /bits/ 8 <50>; - max-cur = /bits/ 8 <100>; - reg = <0x1>; - color = <LED_COLOR_ID_BLUE>; - }; - - led@6 { - led-cur = /bits/ 8 <50>; - max-cur = /bits/ 8 <100>; - reg = <0x6>; - color = <LED_COLOR_ID_RED>; - }; + led-controller@33 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "national,lp5523"; + reg = <0x33>; + clock-mode = /bits/ 8 <0>; + + multi-led@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STANDBY; + linux,default-trigger = "heartbeat"; + + led@0 { + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + reg = <0x0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@1 { + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + reg = <0x1>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@6 { + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + reg = <0x6>; + color = <LED_COLOR_ID_RED>; + }; }; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml b/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml index 6625a528f727..fdaf04e03a8d 100644 --- a/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml +++ b/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml @@ -55,24 +55,24 @@ examples: compatible = "pwm-leds-multicolor"; multi-led { - color = <LED_COLOR_ID_RGB>; - function = LED_FUNCTION_INDICATOR; - max-brightness = <65535>; - - led-red { - pwms = <&pwm1 0 1000000>; - color = <LED_COLOR_ID_RED>; - }; - - led-green { - pwms = <&pwm2 0 1000000>; - color = <LED_COLOR_ID_GREEN>; - }; - - led-blue { - pwms = <&pwm3 0 1000000>; - color = <LED_COLOR_ID_BLUE>; - }; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_INDICATOR; + max-brightness = <65535>; + + led-red { + pwms = <&pwm1 0 1000000>; + color = <LED_COLOR_ID_RED>; + }; + + led-green { + pwms = <&pwm2 0 1000000>; + color = <LED_COLOR_ID_GREEN>; + }; + + led-blue { + pwms = <&pwm3 0 1000000>; + color = <LED_COLOR_ID_BLUE>; + }; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml index 409a4c7298e1..cd02811583ec 100644 --- a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml +++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml @@ -17,6 +17,7 @@ description: > properties: compatible: enum: + - qcom,pm660l-lpg - qcom,pm8150b-lpg - qcom,pm8150l-lpg - qcom,pm8350c-pwm diff --git a/Documentation/devicetree/bindings/leds/skyworks,aat1290.yaml b/Documentation/devicetree/bindings/leds/skyworks,aat1290.yaml new file mode 100644 index 000000000000..a6aaa92dbccd --- /dev/null +++ b/Documentation/devicetree/bindings/leds/skyworks,aat1290.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/skyworks,aat1290.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs + +maintainers: + - Jacek Anaszewski <jacek.anaszewski@gmail.com> + - Krzysztof Kozlowski <krzk@kernel.org> + +description: | + The device is controlled through two pins:: FL_EN and EN_SET. The pins when, + asserted high, enable flash strobe and movie mode (max 1/2 of flash current) + respectively. In order to add a capability of selecting the strobe signal + source (e.g. CPU or camera sensor) there is an additional switch required, + independent of the flash chip. The switch is controlled with pin control. + +properties: + compatible: + const: skyworks,aat1290 + + enset-gpios: + maxItems: 1 + description: EN_SET pin + + flen-gpios: + maxItems: 1 + description: FL_EN pin + + led: + $ref: common.yaml# + unevaluatedProperties: false + + properties: + led-max-microamp: true + + flash-max-microamp: + description: | + Maximum flash LED supply current can be calculated using following + formula:: I = 1A * 162 kOhm / Rset. + + flash-max-timeout-us: + description: | + Maximum flash timeout can be calculated using following formula:: + T = 8.82 * 10^9 * Ct. + + required: + - flash-max-microamp + - flash-max-timeout-us + - led-max-microamp + + pinctrl-names: + items: + - const: default + - const: host + - const: isp + + pinctrl-0: true + pinctrl-1: true + pinctrl-2: true + +required: + - compatible + - enset-gpios + - flen-gpios + - led + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + // Ct = 220 nF, Rset = 160 kOhm + led-controller { + compatible = "skyworks,aat1290"; + flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; + enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default", "host", "isp"; + pinctrl-0 = <&camera_flash_host>; + pinctrl-1 = <&camera_flash_host>; + pinctrl-2 = <&camera_flash_isp>; + + led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + led-max-microamp = <520833>; + flash-max-microamp = <1012500>; + flash-max-timeout-us = <1940000>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt deleted file mode 100644 index 108bf435b933..000000000000 --- a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt +++ /dev/null @@ -1,20 +0,0 @@ -Device-Tree bindings for GPIO IR receiver - -Required properties: - - compatible: should be "gpio-ir-receiver". - - gpios: specifies GPIO used for IR signal reception. - -Optional properties: - - linux,rc-map-name: see rc.txt file in the same - directory. - - linux,autosuspend-period: autosuspend delay time, - the unit is milisecond. - -Example node: - - ir: ir-receiver { - compatible = "gpio-ir-receiver"; - gpios = <&gpio0 19 1>; - linux,rc-map-name = "rc-rc6-mce"; - linux,autosuspend-period = <125>; - }; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml b/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml new file mode 100644 index 000000000000..61072745b983 --- /dev/null +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/gpio-ir-receiver.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO Based IR receiver + +maintainers: + - Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> + +allOf: + - $ref: rc.yaml# + +properties: + compatible: + const: gpio-ir-receiver + + gpios: + maxItems: 1 + + linux,autosuspend-period: + description: autosuspend delay time in milliseconds + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - compatible + - gpios + +unevaluatedProperties: false + +examples: + - | + ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 19 1>; + linux,rc-map-name = "rc-rc6-mce"; + linux,autosuspend-period = <125>; + }; +... diff --git a/Documentation/devicetree/bindings/media/rc.yaml b/Documentation/devicetree/bindings/media/rc.yaml index d4c541c4b164..b11d14ab89c4 100644 --- a/Documentation/devicetree/bindings/media/rc.yaml +++ b/Documentation/devicetree/bindings/media/rc.yaml @@ -12,7 +12,7 @@ maintainers: properties: $nodename: - pattern: "^ir(@[a-f0-9]+)?$" + pattern: "^ir(-receiver)?(@[a-f0-9]+)?$" linux,rc-map-name: description: diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml index fe265bcab50d..fbface720678 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml @@ -74,7 +74,7 @@ properties: rohm,enable-hidden-gpo: description: | The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the - data-sheet as it's location in the middle of GND pins makes it hard to + data-sheet as its location in the middle of GND pins makes it hard to use on PCB. If your board has managed to use this pin you can enable the second GPO by defining this property. Dont enable this if you are unsure about how the E5 pin is connected on your board. diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt index 58d51f480c9e..8ec6191c1712 100644 --- a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -2,7 +2,7 @@ Lantiq XWAY SoC RCU binding =========================== This binding describes the RCU (reset controller unit) multifunction device, -where each sub-device has it's own set of registers. +where each sub-device has its own set of registers. The RCU register range is used for multiple purposes. Mostly one device uses one or multiple register exclusively, but for some registers some diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml index 2cdf6bf3dc4a..8cc2a7ceb5fb 100644 --- a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml +++ b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml @@ -22,13 +22,14 @@ properties: reg: maxItems: 1 - spi-max-frequency: true - required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt deleted file mode 100644 index d5c5616f6db5..000000000000 --- a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt +++ /dev/null @@ -1,17 +0,0 @@ -ARM AFS - ARM Firmware Suite Partitions -======================================= - -The ARM Firmware Suite is a flash partitioning system found on the -ARM reference designs: Integrator AP, Integrator CP, Versatile AB, -Versatile PB, the RealView family, Versatile Express and Juno. - -Required properties: -- compatible : (required) must be "arm,arm-firmware-suite" - -Example: - -flash@0 { - partitions { - compatible = "arm,arm-firmware-suite"; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml new file mode 100644 index 000000000000..76c88027b6d2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml @@ -0,0 +1,28 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/arm,arm-firmware-suite.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Firmware Suite (AFS) Partitions + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The ARM Firmware Suite is a flash partitioning system found on the + ARM reference designs: Integrator AP, Integrator CP, Versatile AB, + Versatile PB, the RealView family, Versatile Express and Juno. + +properties: + compatible: + const: arm,arm-firmware-suite + +additionalProperties: false + +examples: + - | + partitions { + compatible = "arm,arm-firmware-suite"; + }; +... diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt index 0b7d4d3758ea..1d9148ff5130 100644 --- a/Documentation/devicetree/bindings/net/altera_tse.txt +++ b/Documentation/devicetree/bindings/net/altera_tse.txt @@ -15,7 +15,7 @@ Required properties: "rx_desc": MSGDMA Rx dispatcher descriptor space region "rx_resp": MSGDMA Rx dispatcher response space region "s1": SGDMA descriptor memory -- interrupts: Should contain the TSE interrupts and it's mode. +- interrupts: Should contain the TSE interrupts and its mode. - interrupt-names: Should contain the interrupt names "rx_irq": xDMA Rx dispatcher interrupt "tx_irq": xDMA Tx dispatcher interrupt diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 7c7ac5eb0313..ef655f386b2e 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -20,7 +20,7 @@ Required properties: - active_slave : Specifies the slave to use for time stamping, ethtool and SIOCGMIIPHY - cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection - device. See also cpsw-phy-sel.txt for it's binding. + device. See also cpsw-phy-sel.txt for its binding. Note that in legacy cases cpsw-phy-sel may be a child device instead of a phandle (DEPRECATED, use phys property instead). diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt deleted file mode 100644 index 05bd7dafce17..000000000000 --- a/Documentation/devicetree/bindings/net/emac_rockchip.txt +++ /dev/null @@ -1,52 +0,0 @@ -* ARC EMAC 10/100 Ethernet platform driver for Rockchip RK3036/RK3066/RK3188 SoCs - -Required properties: -- compatible: should be "rockchip,<name>-emac" - "rockchip,rk3036-emac": found on RK3036 SoCs - "rockchip,rk3066-emac": found on RK3066 SoCs - "rockchip,rk3188-emac": found on RK3188 SoCs -- reg: Address and length of the register set for the device -- interrupts: Should contain the EMAC interrupts -- rockchip,grf: phandle to the syscon grf used to control speed and mode - for emac. -- phy: see ethernet.txt file in the same directory. -- phy-mode: see ethernet.txt file in the same directory. - -Optional properties: -- phy-supply: phandle to a regulator if the PHY needs one - -Clock handling: -- clocks: Must contain an entry for each entry in clock-names. -- clock-names: Shall be "hclk" for the host clock needed to calculate and set - polling period of EMAC and "macref" for the reference clock needed to transfer - data to and from the phy. - -Child nodes of the driver are the individual PHY devices connected to the -MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. - -Examples: - -ethernet@10204000 { - compatible = "rockchip,rk3188-emac"; - reg = <0xc0fc2000 0x3c>; - interrupts = <6>; - mac-address = [ 00 11 22 33 44 55 ]; - - clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; - clock-names = "hclk", "macref"; - - pinctrl-names = "default"; - pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; - - rockchip,grf = <&grf>; - - phy = <&phy0>; - phy-mode = "rmii"; - phy-supply = <&vcc_rmii>; - - #address-cells = <1>; - #size-cells = <0>; - phy0: ethernet-phy@0 { - reg = <1>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml b/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml index e381a3c14836..b2558421268a 100644 --- a/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml +++ b/Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml @@ -7,7 +7,6 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: NXP Semiconductors NCI NFC controller maintainers: - - Charles Gorand <charles.gorand@effinnov.com> - Krzysztof Kozlowski <krzk@kernel.org> properties: diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt index 346e6c7f47b7..e6cb2291471c 100644 --- a/Documentation/devicetree/bindings/net/qcom-emac.txt +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt @@ -14,7 +14,7 @@ MAC node: - mac-address : The 6-byte MAC address. If present, it is the default MAC address. - internal-phy : phandle to the internal PHY node -- phy-handle : phandle the the external PHY node +- phy-handle : phandle the external PHY node Internal PHY node: - compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii". diff --git a/Documentation/devicetree/bindings/net/rockchip,emac.yaml b/Documentation/devicetree/bindings/net/rockchip,emac.yaml new file mode 100644 index 000000000000..a6d4f14df442 --- /dev/null +++ b/Documentation/devicetree/bindings/net/rockchip,emac.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/rockchip,emac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip RK3036/RK3066/RK3188 Ethernet Media Access Controller (EMAC) + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,rk3036-emac + - rockchip,rk3066-emac + - rockchip,rk3188-emac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + items: + - description: host clock + - description: reference clock + - description: mac TX/RX clock + + clock-names: + minItems: 2 + items: + - const: hclk + - const: macref + - const: macclk + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the syscon GRF used to control speed and mode for the EMAC. + + phy-supply: + description: + Phandle to a regulator if the PHY needs one. + + mdio: + $ref: mdio.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - rockchip,grf + - phy + - phy-mode + - mdio + +allOf: + - $ref: "ethernet-controller.yaml#" + - if: + properties: + compatible: + contains: + const: rockchip,rk3036-emac + + then: + properties: + clocks: + minItems: 3 + + clock-names: + minItems: 3 + + else: + properties: + clocks: + maxItems: 2 + + clock-names: + maxItems: 2 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3188-cru-common.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + ethernet@10204000 { + compatible = "rockchip,rk3188-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; + clock-names = "hclk", "macref"; + rockchip,grf = <&grf>; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; + pinctrl-names = "default"; + phy = <&phy0>; + phy-mode = "rmii"; + phy-supply = <&vcc_rmii>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml index 252e5b72aee0..376e739bcad4 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml @@ -144,6 +144,7 @@ properties: description: If present then the reset sequence using the GPIO specified in the "reset-gpio" property is reversed (H=reset state, L=operation state) (optional required). + type: boolean vpcie-supply: description: Should specify the regulator in charge of PCIe port power. diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.yaml b/Documentation/devicetree/bindings/pci/host-generic-pci.yaml index 6bcaa8f2c3cf..d25423aa7167 100644 --- a/Documentation/devicetree/bindings/pci/host-generic-pci.yaml +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.yaml @@ -106,6 +106,9 @@ properties: maxItems: 3 dma-coherent: true + iommu-map: true + iommu-map-mask: true + msi-parent: true required: - compatible diff --git a/Documentation/devicetree/bindings/perf/arm,ccn.yaml b/Documentation/devicetree/bindings/perf/arm,ccn.yaml new file mode 100644 index 000000000000..0b0bb2091016 --- /dev/null +++ b/Documentation/devicetree/bindings/perf/arm,ccn.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/perf/arm,ccn.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM CCN (Cache Coherent Network) Performance Monitors + +maintainers: + - Robin Murphy <robin.murphy@arm.com> + +properties: + compatible: + enum: + - arm,ccn-502 + - arm,ccn-504 + - arm,ccn-508 + - arm,ccn-512 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + ccn@20000000 { + compatible = "arm,ccn-504"; + reg = <0x20000000 0x1000000>; + interrupts = <0 181 4>; + }; +... diff --git a/Documentation/devicetree/bindings/perf/arm-ccn.txt b/Documentation/devicetree/bindings/perf/arm-ccn.txt deleted file mode 100644 index 1c53b5aa3317..000000000000 --- a/Documentation/devicetree/bindings/perf/arm-ccn.txt +++ /dev/null @@ -1,23 +0,0 @@ -* ARM CCN (Cache Coherent Network) - -Required properties: - -- compatible: (standard compatible string) should be one of: - "arm,ccn-502" - "arm,ccn-504" - "arm,ccn-508" - "arm,ccn-512" - -- reg: (standard registers property) physical address and size - (16MB) of the configuration registers block - -- interrupts: (standard interrupt property) single interrupt - generated by the control block - -Example: - - ccn@2000000000 { - compatible = "arm,ccn-504"; - reg = <0x20 0x00000000 0 0x1000000>; - interrupts = <0 181 4>; - }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml index 4d01f3124e1c..a90fa1baadab 100644 --- a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be the following: "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml index c689bea7ce6e..d3a8911728d0 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be one of the following: "aspeed,ast2400-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml index 9db904a528ee..5d2c1b1fb7fd 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml @@ -17,7 +17,7 @@ description: |+ "aspeed,ast2500-scu", "syscon", "simple-mfd" "aspeed,g5-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml index 3666ac5b6518..e92686d2f062 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be one of the following: "aspeed,ast2600-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml index f005abac7079..5390e988a934 100644 --- a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml +++ b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml @@ -2,8 +2,8 @@ # Copyright 2019 BayLibre, SAS %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Amlogic Meson Everything-Else Power Domains @@ -17,7 +17,7 @@ description: |+ - compatible: Should be the following: "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml index 86e5f6513bb3..eab21bb2050a 100644 --- a/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml +++ b/Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml @@ -3,8 +3,8 @@ # Author: Jianxin Pan <jianxin.pan@amlogic.com> %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/amlogic,meson-sec-pwrc.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/amlogic,meson-sec-pwrc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Amlogic Meson Secure Power Domains diff --git a/Documentation/devicetree/bindings/power/apple,pmgr-pwrstate.yaml b/Documentation/devicetree/bindings/power/apple,pmgr-pwrstate.yaml index 19a194980142..94d369eb85de 100644 --- a/Documentation/devicetree/bindings/power/apple,pmgr-pwrstate.yaml +++ b/Documentation/devicetree/bindings/power/apple,pmgr-pwrstate.yaml @@ -10,7 +10,7 @@ maintainers: - Hector Martin <marcan@marcan.st> allOf: - - $ref: "power-domain.yaml#" + - $ref: power-domain.yaml# description: | Apple SoCs include PMGR blocks responsible for power management, diff --git a/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml b/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml index 63b15ac6dde4..d867bd6976d8 100644 --- a/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml +++ b/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: BCM63xx power domain driver diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.yaml b/Documentation/devicetree/bindings/power/renesas,apmu.yaml index d77fc88050c8..f2cc89e7f4e4 100644 --- a/Documentation/devicetree/bindings/power/renesas,apmu.yaml +++ b/Documentation/devicetree/bindings/power/renesas,apmu.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/renesas,apmu.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/renesas,apmu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Renesas Advanced Power Management Unit diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.yaml b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.yaml index 8d56bedd3390..0720b54881c2 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.yaml +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/renesas,rcar-sysc.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/renesas,rcar-sysc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Renesas R-Car and RZ/G System Controller diff --git a/Documentation/devicetree/bindings/power/reset/qcom,pon.yaml b/Documentation/devicetree/bindings/power/reset/qcom,pon.yaml index 353f155df0f4..e7b436d2e757 100644 --- a/Documentation/devicetree/bindings/power/reset/qcom,pon.yaml +++ b/Documentation/devicetree/bindings/power/reset/qcom,pon.yaml @@ -30,11 +30,15 @@ properties: pwrkey: type: object - $ref: "../../input/qcom,pm8941-pwrkey.yaml#" + $ref: /schemas/input/qcom,pm8941-pwrkey.yaml# resin: type: object - $ref: "../../input/qcom,pm8941-pwrkey.yaml#" + $ref: /schemas/input/qcom,pm8941-pwrkey.yaml# + + watchdog: + type: object + $ref: /schemas/watchdog/qcom,pm8916-wdt.yaml required: - compatible diff --git a/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml b/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml index 03bd1fa5a623..e9417557cd30 100644 --- a/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml +++ b/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml @@ -16,7 +16,7 @@ description: | properties: compatible: - const: "regulator-poweroff" + const: regulator-poweroff cpu-supply: description: diff --git a/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml index 68d7c14a7163..46de35861738 100644 --- a/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml +++ b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml @@ -15,7 +15,7 @@ description: | properties: compatible: - const: "xlnx,zynqmp-power" + const: xlnx,zynqmp-power interrupts: maxItems: 1 diff --git a/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml b/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml index 3f74bc19415d..5220d9cb16d8 100644 --- a/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/active-semi,act8945a-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/active-semi,act8945a-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Active-semi ACT8945A Charger Function diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.yaml b/Documentation/devicetree/bindings/power/supply/bq2415x.yaml index 118cf484cc69..a3c00e078918 100644 --- a/Documentation/devicetree/bindings/power/supply/bq2415x.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq2415x.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq2415x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for TI bq2415x Li-Ion Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.yaml b/Documentation/devicetree/bindings/power/supply/bq24190.yaml index 0d7cbbdf808b..21a9dadc1c6a 100644 --- a/Documentation/devicetree/bindings/power/supply/bq24190.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq24190.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq24190.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq24190.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for TI BQ2419x Li-Ion Battery Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.yaml b/Documentation/devicetree/bindings/power/supply/bq24257.yaml index 3a0f6cd9015a..c7406bef0fa8 100644 --- a/Documentation/devicetree/bindings/power/supply/bq24257.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq24257.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq24257.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq24735.yaml b/Documentation/devicetree/bindings/power/supply/bq24735.yaml index 131be6782c4b..dd9176ce71b3 100644 --- a/Documentation/devicetree/bindings/power/supply/bq24735.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq24735.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq24735.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq24735.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for TI BQ24735 Li-Ion Battery Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml index 813d6afde606..27db38577822 100644 --- a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq2515x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TI bq2515x 500-mA Linear charger family diff --git a/Documentation/devicetree/bindings/power/supply/bq256xx.yaml b/Documentation/devicetree/bindings/power/supply/bq256xx.yaml index 92ec7ed25668..91abe5733c41 100644 --- a/Documentation/devicetree/bindings/power/supply/bq256xx.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq256xx.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq256xx.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq256xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TI bq256xx Switch Mode Buck Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.yaml b/Documentation/devicetree/bindings/power/supply/bq25890.yaml index bf823b615439..204c0147188f 100644 --- a/Documentation/devicetree/bindings/power/supply/bq25890.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq25890.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq25890.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq25890.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq25980.yaml b/Documentation/devicetree/bindings/power/supply/bq25980.yaml index 8367a1fd4057..4883527ab5c7 100644 --- a/Documentation/devicetree/bindings/power/supply/bq25980.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq25980.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq25980.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq25980.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TI BQ25980 Flash Charger diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml index 6af41da3e055..65fc6049efc1 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/bq27xxx.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/bq27xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TI BQ27XXX fuel gauge family diff --git a/Documentation/devicetree/bindings/power/supply/charger-manager.yaml b/Documentation/devicetree/bindings/power/supply/charger-manager.yaml index fbb2204769aa..5af1e0beaf29 100644 --- a/Documentation/devicetree/bindings/power/supply/charger-manager.yaml +++ b/Documentation/devicetree/bindings/power/supply/charger-manager.yaml @@ -50,6 +50,7 @@ properties: cm-battery-stat: description: battery status + $ref: /schemas/types.yaml#/definitions/uint32 enum: - 0 # battery always present - 1 # no battery diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml b/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml index 7153fd4ce55f..694bfdb5815c 100644 --- a/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/cpcap-battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/cpcap-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Motorola CPCAP PMIC battery diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml b/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml index cb6353683d7b..7e6bf30a0107 100644 --- a/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/cpcap-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/cpcap-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Motorola CPCAP PMIC charger diff --git a/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml b/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml index 96336b05d76d..b289388952bf 100644 --- a/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/dlg,da9150-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Dialog Semiconductor DA9150 Charger Power Supply bindings diff --git a/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml b/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml index 30c2fff7cf92..d47caf59d204 100644 --- a/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml +++ b/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-fuel-gauge.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/dlg,da9150-fuel-gauge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings diff --git a/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml b/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml index 76c227a7cd5c..46527038bf22 100644 --- a/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml @@ -2,8 +2,8 @@ # Copyright 2019-2020 Artur Rojek %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/ingenic,battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/ingenic,battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Ingenic JZ47xx battery bindings diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.yaml b/Documentation/devicetree/bindings/power/supply/isp1704.yaml index 4c91da70011d..7e3449ed70d4 100644 --- a/Documentation/devicetree/bindings/power/supply/isp1704.yaml +++ b/Documentation/devicetree/bindings/power/supply/isp1704.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/isp1704.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/isp1704.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for NXP ISP1704 USB Charger Detection diff --git a/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml b/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml index 518eabb63588..a99d989f1450 100644 --- a/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/lego,ev3-battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/lego,ev3-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: LEGO MINDSTORMS EV3 Battery diff --git a/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml b/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml index e2d8d2aebb73..76cedf95a12c 100644 --- a/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/lltc,lt3651-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/lltc,lt3651-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Analog Devices LT3651 Charger Power Supply bindings diff --git a/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml b/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml index 043bf378040f..109b41a0d56c 100644 --- a/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml +++ b/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/lltc,ltc294x.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/lltc,ltc294x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery fuel gauges diff --git a/Documentation/devicetree/bindings/power/supply/ltc4162-l.yaml b/Documentation/devicetree/bindings/power/supply/ltc4162-l.yaml index 6d7aa97a6475..cfffaeef8b09 100644 --- a/Documentation/devicetree/bindings/power/supply/ltc4162-l.yaml +++ b/Documentation/devicetree/bindings/power/supply/ltc4162-l.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020 Topic Embedded Products %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/ltc4162-l.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/ltc4162-l.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Linear Technology (Analog Devices) LTC4162-L Charger diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml index 818647edf63d..c838efcf7e16 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/maxim,ds2760.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/maxim,ds2760.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Maxim DS2760 DT bindings diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml index 0a41078ebd99..070ef6f96e60 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/maxim,max14656.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/maxim,max14656.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Maxim MAX14656 DT bindings diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml index 6b4588a3253b..3a529326ecbd 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml +++ b/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/maxim,max17040.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/maxim,max17040.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Maxim 17040 fuel gauge series diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml index 971b53c58cc6..aff5d0792e0f 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml +++ b/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/maxim,max17042.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/maxim,max17042.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Maxim 17042 fuel gauge series diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml index 4828ca0842ae..a8d625f285f1 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml +++ b/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/maxim,max8903.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/maxim,max8903.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Maxim Semiconductor MAX8903 Battery Charger diff --git a/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml b/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml index 4a1489f2b28d..5178e6207271 100644 --- a/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/nokia,n900-battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/nokia,n900-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Nokia N900 battery diff --git a/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml b/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml index 0bd7bf3b8e1b..dd89e2532a07 100644 --- a/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/olpc-battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/olpc-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: OLPC Battery diff --git a/Documentation/devicetree/bindings/power/supply/power-supply.yaml b/Documentation/devicetree/bindings/power/supply/power-supply.yaml index 9a490fbd32e1..2f672e6e8d72 100644 --- a/Documentation/devicetree/bindings/power/supply/power-supply.yaml +++ b/Documentation/devicetree/bindings/power/supply/power-supply.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/power-supply.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/power-supply.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Power Supply Core Support diff --git a/Documentation/devicetree/bindings/power/supply/richtek,rt5033-battery.yaml b/Documentation/devicetree/bindings/power/supply/richtek,rt5033-battery.yaml index ae647d3355a2..756c16d1727d 100644 --- a/Documentation/devicetree/bindings/power/supply/richtek,rt5033-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/richtek,rt5033-battery.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/richtek,rt5033-battery.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/richtek,rt5033-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Richtek RT5033 PMIC Fuel Gauge diff --git a/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml b/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml index e1c233462f29..bce15101318e 100644 --- a/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml +++ b/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/richtek,rt9455.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/richtek,rt9455.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Binding for Richtek rt9455 battery charger diff --git a/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml index b62c2431f94e..eeb043f9bb4f 100644 --- a/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/sc2731-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/sc2731-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Spreadtrum SC2731 PMICs battery charger binding diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml index e019cffd1f38..d90a838a1744 100644 --- a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml +++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml index 4b8a00cec39c..525abdfb3e2d 100644 --- a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-btemp.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-btemp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AB8500 Battery Temperature Monitor diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml index 6799224f7fb4..10bbdcfc87b6 100644 --- a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-chargalg.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-chargalg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AB8500 Charging Algorithm diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml index 9518eb7289d0..e33329b3af61 100644 --- a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AB8500 Charger diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml index 2ce408a7c0ae..6a724ca90e99 100644 --- a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2021 Sebastian Reichel %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-fg.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-fg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AB8500 Fuel Gauge diff --git a/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml b/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml index 20862cdfc116..0581497448ce 100644 --- a/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Battery charger driver for SMB345, SMB347 and SMB358 diff --git a/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml b/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml index f2dd38bf078c..586745426341 100644 --- a/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/tps65090-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/tps65090-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TPS65090 Frontend PMU with Switchmode Charger diff --git a/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml b/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml index 2c2fe883bb48..7ccf0cdffd3e 100644 --- a/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/tps65217-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/tps65217-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TPS65217 Charger diff --git a/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml b/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml index fe3f32a0ea79..d8d3154f9cb1 100644 --- a/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/twl4030-charger.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/twl4030-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: TWL4030 BCI (Battery Charger Interface) diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml index de6a23aee977..5c8369fd3ef7 100644 --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AXP20x AC power-supply diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml index d055428ae39f..e0b95ecbbebd 100644 --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AXP20x Battery power-supply diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml index 0c371b55c9e1..3ce648dd91bd 100644 --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: AXP20x USB power-supply diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt index d63ab1dec16d..801c66069121 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt @@ -5,7 +5,7 @@ Copyright 2013 Freescale Semiconductor Inc. Power Architecture CPUs in Freescale SOCs are represented in device trees as per the definition in the Devicetree Specification. -In addition to the the Devicetree Specification definitions, the properties +In addition to the Devicetree Specification definitions, the properties defined below may be present on CPU nodes. PROPERTIES diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt index d096cf461d81..4571c857dbe5 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt @@ -172,7 +172,7 @@ Interrupt controller (fsl,mpc5200-pic) node The mpc5200 pic binding splits hardware IRQ numbers into two levels. The split reflects the layout of the PIC hardware itself, which groups interrupts into one of three groups; CRIT, MAIN or PERP. Also, the -Bestcomm dma engine has it's own set of interrupt sources which are +Bestcomm dma engine has its own set of interrupt sources which are cascaded off of peripheral interrupt 0, which the driver interprets as a fourth group, SDMA. diff --git a/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt b/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt index 9d619e955576..d6658d3dd15e 100644 --- a/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt +++ b/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt @@ -39,7 +39,7 @@ otherwise. The length of all the property arrays must be the same. - ibm,cpu-idle-state-flags: Array of unsigned 32-bit values containing the values of the - flags associated with the the aforementioned idle-states. The + flags associated with the aforementioned idle-states. The flag bits are as follows: 0x00000001 /* Decrementer would stop */ 0x00000002 /* Needs timebase restore */ diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index b677900b3aae..658f96fbc4fe 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -37,7 +37,7 @@ on the Qualcomm Hexagon core. - interrupt-names: Usage: required Value type: <stringlist> - Definition: The interrupts needed depends on the the compatible + Definition: The interrupts needed depends on the compatible string: qcom,q6v5-pil: qcom,ipq8074-wcss-pil: diff --git a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt b/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt deleted file mode 100644 index 36f610bb051e..000000000000 --- a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt +++ /dev/null @@ -1,52 +0,0 @@ -Dallas DS1307 and compatible RTC - -Required properties: -- compatible: should be one of: - "dallas,ds1307", - "dallas,ds1308", - "dallas,ds1337", - "dallas,ds1338", - "dallas,ds1339", - "dallas,ds1388", - "dallas,ds1340", - "dallas,ds1341", - "maxim,ds3231", - "st,m41t0", - "st,m41t00", - "st,m41t11", - "microchip,mcp7940x", - "microchip,mcp7941x", - "pericom,pt7c4338", - "epson,rx8025", - "isil,isl12057" - "epson,rx8130" -- reg: I2C bus address of the device - -Optional properties: -- interrupts: rtc alarm interrupt. -- clock-output-names: From common clock binding to override the default output - clock name -- wakeup-source: Enables wake up of host system on alarm -- trickle-resistor-ohms : ds1339, ds1340 and ds 1388 only - Selected resistor for trickle charger - Possible values are 250, 2000, 4000 - Should be given if trickle charger should be enabled -- aux-voltage-chargeable: ds1339, ds1340, ds1388 and rx8130 only - Tells whether the battery/supercap of the RTC (if any) is - chargeable or not. - Possible values are 0 (not chargeable), 1 (chargeable) - -Deprecated properties: -- trickle-diode-disable : ds1339, ds1340 and ds1388 only - Do not use internal trickle charger diode - Should be given if internal trickle charger diode should be disabled - (superseded by aux-voltage-chargeable) - -Example: - ds1339: rtc@68 { - compatible = "dallas,ds1339"; - reg = <0x68>; - interrupt-parent = <&gpio4>; - interrupts = <20 0>; - trickle-resistor-ohms = <250>; - }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-ds1307.yaml b/Documentation/devicetree/bindings/rtc/rtc-ds1307.yaml new file mode 100644 index 000000000000..98d10e680144 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-ds1307.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/rtc-ds1307.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dallas DS1307 and compatible RTC + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +properties: + compatible: + oneOf: + - enum: + - dallas,ds1307 + - dallas,ds1308 + - dallas,ds1337 + - dallas,ds1338 + - dallas,ds1339 + - dallas,ds1388 + - dallas,ds1340 + - dallas,ds1341 + - maxim,ds3231 + - st,m41t0 + - st,m41t00 + - st,m41t11 + - microchip,mcp7940x + - microchip,mcp7941x + - pericom,pt7c4338 + - epson,rx8025 + - isil,isl12057 + - epson,rx8130 + + - items: + - enum: + - st,m41t00 + - const: dallas,ds1338 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + maxItems: 2 + + "#clock-cells": + const: 1 + + clock-output-names: + description: From common clock binding to override the default output clock name. + + wakeup-source: + description: Enables wake up of host system on alarm. + + vcc-supply: true + +allOf: + - $ref: rtc.yaml + - if: + properties: + compatible: + contains: + enum: + - dallas,ds1339 + - dallas,ds1340 + - dallas,ds1388 + then: + properties: + trickle-resistor-ohms: + description: Selected resistor for trickle charger. Should be specified if trickle + charger should be enabled. + enum: [ 250, 2000, 4000 ] + + trickle-diode-disable: + description: Do not use internal trickle charger diode. Should be given if internal + trickle charger diode should be disabled (superseded by aux-voltage-chargeable) + deprecated: true + +unevaluatedProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + interrupt-parent = <&gpio4>; + interrupts = <20 0>; + trickle-resistor-ohms = <250>; + }; + }; diff --git a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml index 13925bb78ec7..d9fc120c61cc 100644 --- a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml +++ b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml @@ -30,6 +30,8 @@ properties: - dallas,ds1672 # Extremely Accurate I²C RTC with Integrated Crystal and SRAM - dallas,ds3232 + # EM Microelectronic EM3027 RTC + - emmicro,em3027 # I2C-BUS INTERFACE REAL TIME CLOCK MODULE - epson,rx8010 # I2C-BUS INTERFACE REAL TIME CLOCK MODULE diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt deleted file mode 100644 index 4f8d8fde0c1c..000000000000 --- a/Documentation/devicetree/bindings/serial/efm32-uart.txt +++ /dev/null @@ -1,20 +0,0 @@ -* Energymicro efm32 UART - -Required properties: -- compatible : Should be "energymicro,efm32-uart" -- reg : Address and length of the register set -- interrupts : Should contain uart interrupt - -Optional properties: -- energymicro,location : Decides the location of the USART I/O pins. - Allowed range : [0 .. 5] - Default: 0 - -Example: - -uart@4000c400 { - compatible = "energymicro,efm32-uart"; - reg = <0x4000c400 0x400>; - interrupts = <15>; - energymicro,location = <0>; -}; diff --git a/Documentation/devicetree/bindings/serio/ps2-gpio.txt b/Documentation/devicetree/bindings/serio/ps2-gpio.txt deleted file mode 100644 index 7b7bc9cdf986..000000000000 --- a/Documentation/devicetree/bindings/serio/ps2-gpio.txt +++ /dev/null @@ -1,23 +0,0 @@ -Device-Tree binding for ps/2 gpio device - -Required properties: - - compatible = "ps2-gpio" - - data-gpios: the data pin - - clk-gpios: the clock pin - - interrupts: Should trigger on the falling edge of the clock line. - -Optional properties: - - write-enable: Indicates whether write function is provided - to serio device. Possibly providing the write fn will not work, because - of the tough timing requirements. - -Example nodes: - -ps2@0 { - compatible = "ps2-gpio"; - interrupt-parent = <&gpio>; - interrupts = <23 IRQ_TYPE_EDGE_FALLING>; - data-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; - clk-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; - write-enable; -}; diff --git a/Documentation/devicetree/bindings/serio/ps2-gpio.yaml b/Documentation/devicetree/bindings/serio/ps2-gpio.yaml new file mode 100644 index 000000000000..a63d9172346f --- /dev/null +++ b/Documentation/devicetree/bindings/serio/ps2-gpio.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serio/ps2-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for GPIO based PS/2 + +maintainers: + - Danilo Krummrich <danilokrummrich@dk-develop.de> + +properties: + compatible: + const: ps2-gpio + + data-gpios: + description: + the gpio used for the data signal - this should be flagged as + active high using open drain with (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN) + from <dt-bindings/gpio/gpio.h> since the signal is open drain by + definition + maxItems: 1 + + clk-gpios: + description: + the gpio used for the clock signal - this should be flagged as + active high using open drain with (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN) + from <dt-bindings/gpio/gpio.h> since the signal is open drain by + definition + maxItems: 1 + + interrupts: + description: + The given interrupt should trigger on the falling edge of the clock line. + maxItems: 1 + + write-enable: + type: boolean + description: + Indicates whether write function is provided to serio device. Possibly + providing the write function will not work, because of the tough timing + requirements. + +required: + - compatible + - data-gpios + - clk-gpios + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + ps2 { + compatible = "ps2-gpio"; + interrupt-parent = <&gpio>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + data-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + clk-gpios = <&gpio 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + write-enable; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml index d01e98768153..a4eeb7e158e5 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml @@ -13,7 +13,7 @@ description: This binding describes the hardware component responsible for side channel requests to the always-on subsystem (AOSS), used for certain power management requests that is not handled by the standard RPMh interface. Each client in the - SoC has it's own block of message RAM and IRQ for communication with the AOSS. + SoC has its own block of message RAM and IRQ for communication with the AOSS. The protocol used to communicate in the message RAM is known as Qualcomm Messaging Protocol (QMP) diff --git a/Documentation/devicetree/bindings/sound/da9055.txt b/Documentation/devicetree/bindings/sound/da9055.txt index ed1b7cc6f249..75c6338b6ae2 100644 --- a/Documentation/devicetree/bindings/sound/da9055.txt +++ b/Documentation/devicetree/bindings/sound/da9055.txt @@ -2,7 +2,7 @@ DA9055 provides Audio CODEC support (I2C only). -The Audio CODEC device in DA9055 has it's own I2C address which is configurable, +The Audio CODEC device in DA9055 has its own I2C address which is configurable, so the device is instantiated separately from the PMIC (MFD) device. For details on accompanying PMIC I2C device, see the following: diff --git a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml index 2ad17b361db0..bc2fb1a80ed7 100644 --- a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml +++ b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml @@ -68,9 +68,9 @@ properties: array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>. 0 - (default) Odd channel is latched on the negative edge and even - channel is latched on the the positive edge. + channel is latched on the positive edge. 1 - Odd channel is latched on the positive edge and even channel is - latched on the the negative edge. + latched on the negative edge. PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt deleted file mode 100644 index e0fa61a1be0c..000000000000 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ /dev/null @@ -1,39 +0,0 @@ -* Energy Micro EFM32 SPI - -Required properties: -- #address-cells: see spi-bus.txt -- #size-cells: see spi-bus.txt -- compatible: should be "energymicro,efm32-spi" -- reg: Offset and length of the register set for the controller -- interrupts: pair specifying rx and tx irq -- clocks: phandle to the spi clock -- cs-gpios: see spi-bus.txt - -Recommended properties : -- energymicro,location: Value to write to the ROUTE register's LOCATION - bitfield to configure the pinmux for the device, see - datasheet for values. - If this property is not provided, keeping what is - already configured in the hardware, so its either the - reset default 0 or whatever the bootloader did. - -Example: - -spi1: spi@4000c400 { /* USART1 */ - #address-cells = <1>; - #size-cells = <0>; - compatible = "energymicro,efm32-spi"; - reg = <0x4000c400 0x400>; - interrupts = <15 16>; - clocks = <&cmu 20>; - cs-gpios = <&gpio 51 1>; // D3 - energymicro,location = <1>; - - ks8851@0 { - compatible = "ks8851"; - spi-max-frequency = <6000000>; - reg = <0>; - interrupt-parent = <&boardfpga>; - interrupts = <4>; - }; -}; diff --git a/Documentation/devicetree/bindings/sram/qcom,imem.yaml b/Documentation/devicetree/bindings/sram/qcom,imem.yaml new file mode 100644 index 000000000000..e9199190198d --- /dev/null +++ b/Documentation/devicetree/bindings/sram/qcom,imem.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sram/qcom,imem.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm IMEM memory region + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +description: + Qualcomm IMEM is dedicated memory region for various debug features and DMA + transactions. + +properties: + compatible: + items: + - enum: + - qcom,apq8064-imem + - qcom,msm8974-imem + - qcom,qcs404-imem + - qcom,sc7180-imem + - qcom,sc7280-imem + - qcom,sdm630-imem + - qcom,sdm845-imem + - qcom,sdx55-imem + - const: syscon + - const: simple-mfd + + reg: + maxItems: 1 + + ranges: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + reboot-mode: + $ref: /schemas/power/reset/syscon-reboot-mode.yaml# + +patternProperties: + "^pil-reloc@[0-9a-f]+$": + $ref: /schemas/remoteproc/qcom,pil-info.yaml# + description: Peripheral image loader relocation region + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + soc { + #address-cells = <2>; + #size-cells = <2>; + + sram@146bf000 { + compatible = "qcom,sdm845-imem", "syscon", "simple-mfd"; + reg = <0 0x146bf000 0 0x1000>; + ranges = <0 0 0x146bf000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + + pil-reloc@94c { + compatible = "qcom,pil-reloc-info"; + reg = <0x94c 0xc8>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sram/qcom,ocmem.yaml b/Documentation/devicetree/bindings/sram/qcom,ocmem.yaml index 930188bc5e6a..071f2d676196 100644 --- a/Documentation/devicetree/bindings/sram/qcom,ocmem.yaml +++ b/Documentation/devicetree/bindings/sram/qcom,ocmem.yaml @@ -72,10 +72,10 @@ patternProperties: examples: - | - #include <dt-bindings/clock/qcom,rpmcc.h> - #include <dt-bindings/clock/qcom,mmcc-msm8974.h> + #include <dt-bindings/clock/qcom,rpmcc.h> + #include <dt-bindings/clock/qcom,mmcc-msm8974.h> - ocmem: ocmem@fdd00000 { + sram@fdd00000 { compatible = "qcom,msm8974-ocmem"; reg = <0xfdd00000 0x2000>, @@ -93,6 +93,6 @@ examples: ranges = <0 0xfec00000 0x100000>; gmu-sram@0 { - reg = <0x0 0x100000>; + reg = <0x0 0x100000>; }; - }; + }; diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml index 1ab5070c751d..89a2c32c0ab2 100644 --- a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml +++ b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be one of the following: "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: diff --git a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt index db880e7ed713..aea4a2a178b9 100644 --- a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt @@ -96,7 +96,7 @@ critical trip point is reported back to the thermal framework to implement software shutdown. - the "hot" type trip points will be set to SOC_THERM hardware as the throttle -temperature. Once the the temperature of this thermal zone is higher +temperature. Once the temperature of this thermal zone is higher than it, it will trigger the HW throttle event. Example : diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.yaml b/Documentation/devicetree/bindings/thermal/rcar-thermal.yaml index 927de79ab4b5..00dcbdd36144 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.yaml +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.yaml @@ -42,7 +42,7 @@ properties: description: Address ranges of the thermal registers. If more then one range is given the first one must be the common registers followed by each sensor - according the the datasheet. + according the datasheet. minItems: 1 maxItems: 4 diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 5a3bc64773a9..2f0151e9f6be 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -141,6 +141,8 @@ patternProperties: description: ASIX Electronics Corporation "^aspeed,.*": description: ASPEED Technology Inc. + "^asrock,.*": + description: ASRock Inc. "^asus,.*": description: AsusTek Computer Inc. "^atheros,.*": @@ -198,12 +200,14 @@ patternProperties: description: Broadcom Corporation "^bsh,.*": description: BSH Hausgeraete GmbH + "^bticino,.*": + description: Bticino International "^buffalo,.*": description: Buffalo, Inc. "^bur,.*": description: B&R Industrial Automation GmbH - "^bticino,.*": - description: Bticino International + "^bytedance,.*": + description: ByteDance Ltd. "^calamp,.*": description: CalAmp Corp. "^calaosystems,.*": @@ -308,6 +312,8 @@ patternProperties: description: Dell Inc. "^delta,.*": description: Delta Electronics, Inc. + "^densitron,.*": + description: Densitron Technologies Ltd "^denx,.*": description: Denx Software Engineering "^devantech,.*": @@ -551,6 +557,8 @@ patternProperties: description: Shenzhen Hugsun Technology Co. Ltd. "^hwacom,.*": description: HwaCom Systems Inc. + "^hxt,.*": + description: HXT Semiconductor "^hycon,.*": description: Hycon Technology Corp. "^hydis,.*": @@ -585,6 +593,8 @@ patternProperties: description: Infineon Technologies "^inforce,.*": description: Inforce Computing + "^ingrasys,.*": + description: Ingrasys Technology Inc. "^ivo,.*": description: InfoVision Optoelectronics Kunshan Co. Ltd. "^ingenic,.*": @@ -605,6 +615,8 @@ patternProperties: description: Inter Control Group "^invensense,.*": description: InvenSense Inc. + "^inventec,.*": + description: Inventec "^inversepath,.*": description: Inverse Path "^iom,.*": @@ -1019,6 +1031,8 @@ patternProperties: description: Shenzhen QiShenglong Industrialist Co., Ltd. "^qnap,.*": description: QNAP Systems, Inc. + "^quanta,.*": + description: Quanta Computer Inc. "^radxa,.*": description: Radxa "^raidsonic,.*": diff --git a/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.yaml b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.yaml index ca9e1beff76b..6ecd429f76b5 100644 --- a/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.yaml +++ b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.yaml @@ -55,7 +55,7 @@ examples: compatible = "faraday,ftwdt010"; reg = <0x41000000 0x1000>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; - timeout-secs = <5>; + timeout-sec = <5>; }; - | watchdog: watchdog@98500000 { diff --git a/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt deleted file mode 100644 index 6fb984f31982..000000000000 --- a/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt +++ /dev/null @@ -1,28 +0,0 @@ -QCOM PM8916 watchdog timer controller - -This pm8916 watchdog timer controller must be under pm8916-pon node. - -Required properties: -- compatible: should be "qcom,pm8916-wdt" - -Optional properties : -- interrupts : Watchdog pre-timeout (bark) interrupt. -- timeout-sec : Watchdog timeout value in seconds. - -Example: - - pm8916_0: pm8916@0 { - compatible = "qcom,pm8916", "qcom,spmi-pmic"; - reg = <0x0 SPMI_USID>; - - pon@800 { - compatible = "qcom,pm8916-pon"; - reg = <0x800>; - - watchdog { - compatible = "qcom,pm8916-wdt"; - interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>; - timeout-sec = <10>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.yaml b/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.yaml new file mode 100644 index 000000000000..568eb8480fc3 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/qcom,pm8916-wdt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm PM8916 watchdog timer controller + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +allOf: + - $ref: watchdog.yaml# + +properties: + compatible: + const: qcom,pm8916-wdt + + interrupts: + maxItems: 1 + +required: + - compatible + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/spmi/spmi.h> + + pmic@0 { + compatible = "qcom,pm8916", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x800>; + mode-bootloader = <0x2>; + mode-recovery = <0x1>; + + watchdog { + compatible = "qcom,pm8916-wdt"; + interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>; + timeout-sec = <60>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/writing-bindings.rst b/Documentation/devicetree/bindings/writing-bindings.rst index 5465eced2af1..1ad081de2dd0 100644 --- a/Documentation/devicetree/bindings/writing-bindings.rst +++ b/Documentation/devicetree/bindings/writing-bindings.rst @@ -53,7 +53,7 @@ Properties - DO use common property unit suffixes for properties with scientific units. Recommended suffixes are listed at - https://github.com/devicetree-org/dt-schema/blob/master/schemas/property-units.yaml + https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml - DO define properties in terms of constraints. How many entries? What are possible values? What is the order? |