Merge branch 'master' into for-next

Conflicts:
	arch/arm/mach-omap1/board-nokia770.c

1 files changed, 157 insertions, 0 deletions

diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665
new file mode 100644
index 000000000000..3820fc9ca52d
--- /dev/null
+++ b/Documentation/hwmon/smm665
@@ -0,0 +1,157 @@
+Kernel driver smm665
+====================
+
+Supported chips:
+  * Summit Microelectronics SMM465
+    Prefix: 'smm465'
+    Addresses scanned: -
+    Datasheet:
+      http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf
+  * Summit Microelectronics SMM665, SMM665B
+    Prefix: 'smm665'
+    Addresses scanned: -
+    Datasheet:
+      http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf
+  * Summit Microelectronics SMM665C
+    Prefix: 'smm665c'
+    Addresses scanned: -
+    Datasheet:
+      http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf
+  * Summit Microelectronics SMM764
+    Prefix: 'smm764'
+    Addresses scanned: -
+    Datasheet:
+      http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf
+  * Summit Microelectronics SMM766, SMM766B
+    Prefix: 'smm766'
+    Addresses scanned: -
+    Datasheets:
+      http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf
+      http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Module Parameters
+-----------------
+
+* vref: int
+  Default: 1250 (mV)
+  Reference voltage on VREF_ADC pin in mV. It should not be necessary to set
+  this parameter unless a non-default reference voltage is used.
+
+
+Description
+-----------
+
+[From datasheet] The SMM665 is an Active DC Output power supply Controller
+that monitors, margins and cascade sequences power. The part monitors six
+power supply channels as well as VDD, 12V input, two general-purpose analog
+inputs and an internal temperature sensor using a 10-bit ADC.
+
+Each monitored channel has its own high and low limits, plus a critical
+limit.
+
+Support for SMM465, SMM764, and SMM766 has been implemented but is untested.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for devices, since there is no register which
+can be safely used to identify the chip. You will have to instantiate
+the devices explicitly. When instantiating the device, you have to specify
+its configuration register address.
+
+Example: the following will load the driver for an SMM665 at address 0x57
+on I2C bus #1:
+$ modprobe smm665
+$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+This driver uses the values in the datasheet to convert ADC register values
+into the values specified in the sysfs-interface document. All attributes are
+read only.
+
+Min, max, lcrit, and crit values are used by the chip to trigger external signals
+and/or other activity. Triggered signals can include HEALTHY, RST, Power Off,
+or Fault depending on the chip configuration. The driver reports values as lcrit
+or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or
+max otherwise. For details please see the SMM665 datasheet.
+
+For SMM465 and SMM764, values for Channel E and F are reported but undefined.
+
+in1_input		12V input voltage (mV)
+in2_input		3.3V (VDD) input voltage (mV)
+in3_input		Channel A voltage (mV)
+in4_input		Channel B voltage (mV)
+in5_input		Channel C voltage (mV)
+in6_input		Channel D voltage (mV)
+in7_input		Channel E voltage (mV)
+in8_input		Channel F voltage (mV)
+in9_input		AIN1 voltage (mV)
+in10_input		AIN2 voltage (mV)
+
+in1_min			12v input minimum voltage (mV)
+in2_min			3.3V (VDD) input minimum voltage (mV)
+in3_min			Channel A minimum voltage (mV)
+in4_min			Channel B minimum voltage (mV)
+in5_min			Channel C minimum voltage (mV)
+in6_min			Channel D minimum voltage (mV)
+in7_min			Channel E minimum voltage (mV)
+in8_min			Channel F minimum voltage (mV)
+in9_min			AIN1 minimum voltage (mV)
+in10_min		AIN2 minimum voltage (mV)
+
+in1_max			12v input maximum voltage (mV)
+in2_max			3.3V (VDD) input maximum voltage (mV)
+in3_max			Channel A maximum voltage (mV)
+in4_max			Channel B maximum voltage (mV)
+in5_max			Channel C maximum voltage (mV)
+in6_max			Channel D maximum voltage (mV)
+in7_max			Channel E maximum voltage (mV)
+in8_max			Channel F maximum voltage (mV)
+in9_max			AIN1 maximum voltage (mV)
+in10_max		AIN2 maximum voltage (mV)
+
+in1_lcrit		12v input critical minimum voltage (mV)
+in2_lcrit		3.3V (VDD) input critical minimum voltage (mV)
+in3_lcrit		Channel A critical minimum voltage (mV)
+in4_lcrit		Channel B critical minimum voltage (mV)
+in5_lcrit		Channel C critical minimum voltage (mV)
+in6_lcrit		Channel D critical minimum voltage (mV)
+in7_lcrit		Channel E critical minimum voltage (mV)
+in8_lcrit		Channel F critical minimum voltage (mV)
+in9_lcrit		AIN1 critical minimum voltage (mV)
+in10_lcrit		AIN2 critical minimum voltage (mV)
+
+in1_crit		12v input critical maximum voltage (mV)
+in2_crit		3.3V (VDD) input critical maximum voltage (mV)
+in3_crit		Channel A critical maximum voltage (mV)
+in4_crit		Channel B critical maximum voltage (mV)
+in5_crit		Channel C critical maximum voltage (mV)
+in6_crit		Channel D critical maximum voltage (mV)
+in7_crit		Channel E critical maximum voltage (mV)
+in8_crit		Channel F critical maximum voltage (mV)
+in9_crit		AIN1 critical maximum voltage (mV)
+in10_crit		AIN2 critical maximum voltage (mV)
+
+in1_crit_alarm		12v input critical alarm
+in2_crit_alarm		3.3V (VDD) input critical alarm
+in3_crit_alarm		Channel A critical alarm
+in4_crit_alarm		Channel B critical alarm
+in5_crit_alarm		Channel C critical alarm
+in6_crit_alarm		Channel D critical alarm
+in7_crit_alarm		Channel E critical alarm
+in8_crit_alarm		Channel F critical alarm
+in9_crit_alarm		AIN1 critical alarm
+in10_crit_alarm		AIN2 critical alarm
+
+temp1_input		Chip tempererature
+temp1_min		Mimimum chip tempererature
+temp1_max		Maximum chip tempererature
+temp1_crit		Critical chip tempererature
+temp1_crit_alarm	Temperature critical alarm