Merge branch 'master' of /home/cbou/linux-2.6

Conflicts:

	drivers/power/Kconfig
	drivers/power/Makefile

1 files changed, 123 insertions, 24 deletions

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index a3c35446e755..e7bea3e85304 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -87,7 +87,8 @@ parameter is applicable:
 	SH	SuperH architecture is enabled.
 	SMP	The kernel is an SMP kernel.
 	SPARC	Sparc architecture is enabled.
-	SWSUSP	Software suspend is enabled.
+	SWSUSP	Software suspend (hibernation) is enabled.
+	SUSPEND	System suspend states are enabled.
 	TS	Appropriate touchscreen support is enabled.
 	USB	USB support is enabled.
 	USBHID	USB Human Interface Device support is enabled.
@@ -147,10 +148,16 @@ and is between 256 and 4096 characters. It is defined in the file
 			default: 0
 
 	acpi_sleep=	[HW,ACPI] Sleep options
-			Format: { s3_bios, s3_mode, s3_beep }
+			Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, old_ordering }
 			See Documentation/power/video.txt for s3_bios and s3_mode.
 			s3_beep is for debugging; it makes the PC's speaker beep
 			as soon as the kernel's real-mode entry point is called.
+			s4_nohwsig prevents ACPI hardware signature from being
+			used during resume from hibernation.
+			old_ordering causes the ACPI 1.0 ordering of the _PTS
+			control method, wrt putting devices into low power
+			states, to be enforced (the ACPI 2.0 ordering of _PTS is
+			used by default).
 
 	acpi_sci=	[HW,ACPI] ACPI System Control Interrupt trigger mode
 			Format: { level | edge | high | low }
@@ -271,6 +278,17 @@ and is between 256 and 4096 characters. It is defined in the file
 	aic79xx=	[HW,SCSI]
 			See Documentation/scsi/aic79xx.txt.
 
+	amd_iommu=	[HW,X86-84]
+			Pass parameters to the AMD IOMMU driver in the system.
+			Possible values are:
+			isolate - enable device isolation (each device, as far
+			          as possible, will get its own protection
+			          domain)
+	amd_iommu_size= [HW,X86-64]
+			Define the size of the aperture for the AMD IOMMU
+			driver. Possible values are:
+			'32M', '64M' (default), '128M', '256M', '512M', '1G'
+
 	amijoy.map=	[HW,JOY] Amiga joystick support
 			Map of devices attached to JOY0DAT and JOY1DAT
 			Format: <a>,<b>
@@ -295,7 +313,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			when initialising the APIC and IO-APIC components.
 
 	apm=		[APM] Advanced Power Management
-			See header of arch/i386/kernel/apm.c.
+			See header of arch/x86/kernel/apm_32.c.
 
 	arcrimi=	[HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
 			Format: <io>,<irq>,<nodeID>
@@ -398,9 +416,6 @@ and is between 256 and 4096 characters. It is defined in the file
 	cio_ignore=	[S390]
 			See Documentation/s390/CommonIO for details.
 
-	cio_msg=	[S390]
-			See Documentation/s390/CommonIO for details.
-
 	clock=		[BUGS=X86-32, HW] gettimeofday clocksource override.
 			[Deprecated]
 			Forces specified clocksource (if available) to be used
@@ -563,6 +578,8 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	debug_objects	[KNL] Enable object debugging
 
+	debugpat	[X86] Enable PAT debugging
+
 	decnet.addr=	[HW,NET]
 			Format: <area>[,<node>]
 			See also Documentation/networking/decnet.txt.
@@ -602,6 +619,29 @@ and is between 256 and 4096 characters. It is defined in the file
 			See drivers/char/README.epca and
 			Documentation/digiepca.txt.
 
+	disable_mtrr_cleanup [X86]
+	enable_mtrr_cleanup [X86]
+			The kernel tries to adjust MTRR layout from continuous
+			to discrete, to make X server driver able to add WB
+			entry later. This parameter enables/disables that.
+
+	mtrr_chunk_size=nn[KMG] [X86]
+			used for mtrr cleanup. It is largest continous chunk
+			that could hold holes aka. UC entries.
+
+	mtrr_gran_size=nn[KMG] [X86]
+			Used for mtrr cleanup. It is granularity of mtrr block.
+			Default is 1.
+			Large value could prevent small alignment from
+			using up MTRRs.
+
+	mtrr_spare_reg_nr=n [X86]
+			Format: <integer>
+			Range: 0,7 : spare reg number
+			Default : 1
+			Used for mtrr cleanup. It is spare mtrr entries number.
+			Set to 2 or more if your graphical card needs more.
+
 	disable_mtrr_trim [X86, Intel and AMD only]
 			By default the kernel will trim any uncacheable
 			memory out of your available memory pool based on
@@ -641,7 +681,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	elanfreq=	[X86-32]
 			See comment before function elanfreq_setup() in
-			arch/i386/kernel/cpu/cpufreq/elanfreq.c.
+			arch/x86/kernel/cpu/cpufreq/elanfreq.c.
 
 	elevator=	[IOSCHED]
 			Format: {"anticipatory" | "cfq" | "deadline" | "noop"}
@@ -689,6 +729,12 @@ and is between 256 and 4096 characters. It is defined in the file
 	floppy=		[HW]
 			See Documentation/floppy.txt.
 
+	force_pal_cache_flush
+			[IA-64] Avoid check_sal_cache_flush which may hang on
+			buggy SAL_CACHE_FLUSH implementations. Using this
+			parameter will force ia64_sal_cache_flush to call
+			ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
+
 	gamecon.map[2|3]=
 			[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
 			support via parallel port (up to 5 devices per port)
@@ -719,9 +765,6 @@ and is between 256 and 4096 characters. It is defined in the file
 	hd=		[EIDE] (E)IDE hard drive subsystem geometry
 			Format: <cyl>,<head>,<sect>
 
-	hd?=		[HW] (E)IDE subsystem
-	hd?lun=		See Documentation/ide/ide.txt.
-
 	highmem=nn[KMG]	[KNL,BOOT] forces the highmem zone to have an exact
 			size of <nn>. This works even on boxes that have no
 			highmem otherwise. This also works to reduce highmem
@@ -734,8 +777,22 @@ and is between 256 and 4096 characters. It is defined in the file
 	hisax=		[HW,ISDN]
 			See Documentation/isdn/README.HiSax.
 
-	hugepages=	[HW,X86-32,IA-64] Maximal number of HugeTLB pages.
-	hugepagesz=	[HW,IA-64,PPC] The size of the HugeTLB pages.
+	hugepages=	[HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
+	hugepagesz=	[HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
+			On x86-64 and powerpc, this option can be specified
+			multiple times interleaved with hugepages= to reserve
+			huge pages of different sizes. Valid pages sizes on
+			x86-64 are 2M (when the CPU supports "pse") and 1G
+			(when the CPU supports the "pdpe1gb" cpuinfo flag)
+			Note that 1GB pages can only be allocated at boot time
+			using hugepages= and not freed afterwards.
+	default_hugepagesz=
+			[same as hugepagesz=] The size of the default
+			HugeTLB page size. This is the size represented by
+			the legacy /proc/ hugepages APIs, used for SHM, and
+			default size when mounting hugetlbfs filesystems.
+			Defaults to the default architecture's huge page size
+			if not specified.
 
 	i8042.direct	[HW] Put keyboard port into non-translated mode
 	i8042.dumbkbd	[HW] Pretend that controller can only read data from
@@ -782,7 +839,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			See Documentation/ide/ide.txt.
 
 	idle=		[X86]
-			Format: idle=poll or idle=mwait
+			Format: idle=poll or idle=mwait, idle=halt, idle=nomwait
 			Poll forces a polling idle loop that can slightly improves the performance
 			of waking up a idle CPU, but will use a lot of power and make the system
 			run hot. Not recommended.
@@ -790,6 +847,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			to not use it because it doesn't save as much power as a normal idle
 			loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
 			as idle=poll.
+			idle=halt. Halt is forced to be used for CPU idle.
+			In such case C2/C3 won't be used again.
+			idle=nomwait. Disable mwait for CPU C-states
 
 	ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
 			Claim all unknown PCI IDE storage controllers.
@@ -1094,9 +1154,6 @@ and is between 256 and 4096 characters. It is defined in the file
 	mac5380=	[HW,SCSI] Format:
 			<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
 
-	mac53c9x=	[HW,SCSI] Format:
-			<num_esps>,<disconnect>,<nosync>,<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
-
 	machvec=	[IA64] Force the use of a particular machine-vector
 			(machvec) in a generic kernel.
 			Example: machvec=hpzx1_swiotlb
@@ -1166,7 +1223,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			         or
 			         memmap=0x10000$0x18690000
 
-	memtest=	[KNL,X86_64] Enable memtest
+	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
 			range: 0,4 : pattern number
 			default : 0 <disable>
@@ -1185,6 +1242,14 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	mga=		[HW,DRM]
 
+	mminit_loglevel=
+			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
+			parameter allows control of the logging verbosity for
+			the additional memory initialisation checks. A value
+			of 0 disables mminit logging and a level of 4 will
+			log everything. Information is printed at KERN_DEBUG
+			so loglevel=8 may also need to be specified.
+
 	mousedev.tap_time=
 			[MOUSE] Maximum time between finger touching and
 			leaving touchpad surface for touch to be considered
@@ -1208,6 +1273,11 @@ and is between 256 and 4096 characters. It is defined in the file
 	mtdparts=	[MTD]
 			See drivers/mtd/cmdlinepart.c.
 
+	mtdset=		[ARM]
+			ARM/S3C2412 JIVE boot control
+
+			See arch/arm/mach-s3c2412/mach-jive.c
+
 	mtouchusb.raw_coordinates=
 			[HW] Make the MicroTouch USB driver use raw coordinates
 			('y', default) or cooked coordinates ('n')
@@ -1234,6 +1304,13 @@ and is between 256 and 4096 characters. It is defined in the file
 			This usage is only documented in each driver source
 			file if at all.
 
+	nf_conntrack.acct=
+			[NETFILTER] Enable connection tracking flow accounting
+			0 to disable accounting
+			1 to enable accounting
+			Default value depends on CONFIG_NF_CT_ACCT that is
+			going to be removed in 2.6.29.
+
 	nfsaddrs=	[NFS]
 			See Documentation/filesystems/nfsroot.txt.
 
@@ -1496,6 +1573,9 @@ and is between 256 and 4096 characters. It is defined in the file
 				Use with caution as certain devices share
 				address decoders between ROMs and other
 				resources.
+		norom		[X86-32,X86_64] Do not assign address space to
+				expansion ROMs that do not already have
+				BIOS assigned address ranges.
 		irqmask=0xMMMM	[X86-32] Set a bit mask of IRQs allowed to be
 				assigned automatically to PCI devices. You can
 				make the kernel exclude IRQs of your ISA cards
@@ -1525,6 +1605,8 @@ and is between 256 and 4096 characters. It is defined in the file
 				This is normally done in pci_enable_device(),
 				so this option is a temporary workaround
 				for broken drivers that don't call it.
+		skip_isa_align	[X86] do not align io start addr, so can
+				handle more pci cards
 		firmware	[ARM] Do not re-enumerate the bus but instead
 				just use the configuration from the
 				bootloader. This is currently used on
@@ -1569,6 +1651,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			Format: { parport<nr> | timid | 0 }
 			See also Documentation/parport.txt.
 
+	pmtmr=		[X86] Manual setup of pmtmr I/O Port. 
+			Override pmtimer IOPort with a hex value.
+			e.g. pmtmr=0x508
+
 	pnpacpi=	[ACPI]
 			{ off }
 
@@ -1677,6 +1763,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			Format: <reboot_mode>[,<reboot_mode2>[,...]]
 			See arch/*/kernel/reboot.c or arch/*/kernel/process.c			
 
+	relax_domain_level=
+			[KNL, SMP] Set scheduler's default relax_domain_level.
+			See Documentation/cpusets.txt.
+
 	reserve=	[KNL,BUGS] Force the kernel to ignore some iomem area
 
 	reservetop=	[X86-32]
@@ -1969,6 +2059,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	snd-ymfpci=	[HW,ALSA]
 
+	softlockup_panic=
+			[KNL] Should the soft-lockup detector generate panics.
+
 	sonypi.*=	[HW] Sony Programmable I/O Control Device driver
 			See Documentation/sonypi.txt
 
@@ -2033,6 +2126,12 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	tdfx=		[HW,DRM]
 
+	test_suspend=	[SUSPEND]
+			Specify "mem" (for Suspend-to-RAM) or "standby" (for
+			standby suspend) as the system sleep state to briefly
+			enter during system startup.  The system is woken from
+			this state using a wakeup-capable RTC alarm.
+
 	thash_entries=	[KNL,NET]
 			Set number of hash buckets for TCP connection
 
@@ -2060,13 +2159,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			<deci-seconds>: poll all this frequency
 			0: no polling (default)
 
-	tipar.timeout=	[HW,PPT]
-			Set communications timeout in tenths of a second
-			(default 15).
-
-	tipar.delay=	[HW,PPT]
-			Set inter-bit delay in microseconds (default 10).
-
 	tmscsim=	[HW,SCSI]
 			See comment before function dc390_setup() in
 			drivers/scsi/tmscsim.c.
@@ -2100,6 +2192,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			Note that genuine overcurrent events won't be
 			reported either.
 
+	unknown_nmi_panic
+			[X86-32,X86-64]
+			Set unknown_nmi_panic=1 early on boot.
+
 	usbcore.autosuspend=
 			[USB] The autosuspend time delay (in seconds) used
 			for newly-detected USB devices (default 2).  This
@@ -2110,6 +2206,9 @@ and is between 256 and 4096 characters. It is defined in the file
 	usbhid.mousepoll=
 			[USBHID] The interval which mice are to be polled at.
 
+	add_efi_memmap	[EFI; x86-32,X86-64] Include EFI memory map in
+			kernel's map of available physical RAM.
+
 	vdso=		[X86-32,SH,x86-64]
 			vdso=2: enable compat VDSO (default with COMPAT_VDSO)
 			vdso=1: enable VDSO (default)