Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 1511 insertions, 0 deletions

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
new file mode 100644
index 000000000000..4924d387a657
--- /dev/null
+++ b/Documentation/kernel-parameters.txt
@@ -0,0 +1,1511 @@
+February 2003             Kernel Parameters                     v2.5.59
+                          ~~~~~~~~~~~~~~~~~
+
+The following is a consolidated list of the kernel parameters as implemented
+(mostly) by the __setup() macro and sorted into English Dictionary order
+(defined as ignoring all punctuation and sorting digits before letters in a
+case insensitive manner), and with descriptions where known.
+
+Module parameters for loadable modules are specified only as the
+parameter name with optional '=' and value as appropriate, such as:
+
+	modprobe usbcore blinkenlights=1
+
+Module parameters for modules that are built into the kernel image
+are specified on the kernel command line with the module name plus
+'.' plus parameter name, with '=' and value if appropriate, such as:
+
+	usbcore.blinkenlights=1
+
+The text in square brackets at the beginning of the description state the
+restrictions on the kernel for the said kernel parameter to be valid. The
+restrictions referred to are that the relevant option is valid if:
+
+	ACPI	ACPI support is enabled.
+	ALSA	ALSA sound support is enabled.
+	APIC	APIC support is enabled.
+	APM	Advanced Power Management support is enabled.
+	AX25	Appropriate AX.25 support is enabled.
+	CD	Appropriate CD support is enabled.
+	DEVFS	devfs support is enabled. 
+	DRM	Direct Rendering Management support is enabled. 
+	EDD	BIOS Enhanced Disk Drive Services (EDD) is enabled
+	EFI	EFI Partitioning (GPT) is enabled
+	EIDE	EIDE/ATAPI support is enabled.
+	FB	The frame buffer device is enabled.
+	HW	Appropriate hardware is enabled.
+	IA-32	IA-32 aka i386 architecture is enabled.
+	IA-64	IA-64 architecture is enabled.
+	IOSCHED	More than one I/O scheduler is enabled.
+	IP_PNP	IP DCHP, BOOTP, or RARP is enabled.
+	ISAPNP	ISA PnP code is enabled.
+	ISDN	Appropriate ISDN support is enabled.
+	JOY	Appropriate joystick support is enabled.
+	LP	Printer support is enabled.
+	LOOP	Loopback device support is enabled.
+	M68k	M68k architecture is enabled.
+			These options have more detailed description inside of
+			Documentation/m68k/kernel-options.txt.
+	MCA	MCA bus support is enabled.
+	MDA	MDA console support is enabled.
+	MOUSE	Appropriate mouse support is enabled.
+	MTD	MTD support is enabled.
+	NET	Appropriate network support is enabled.
+	NUMA	NUMA support is enabled.
+	NFS	Appropriate NFS support is enabled.
+	OSS	OSS sound support is enabled.
+	PARIDE	The ParIDE subsystem is enabled.
+	PARISC	The PA-RISC architecture is enabled.
+	PCI	PCI bus support is enabled.
+	PCMCIA	The PCMCIA subsystem is enabled.
+	PNP	Plug & Play support is enabled.
+	PPC	PowerPC architecture is enabled.
+	PPT	Parallel port support is enabled.
+	PS2	Appropriate PS/2 support is enabled.
+	RAM	RAM disk support is enabled.
+	S390	S390 architecture is enabled.
+	SCSI	Appropriate SCSI support is enabled.
+			A lot of drivers has their options described inside of
+			Documentation/scsi/.
+	SELINUX SELinux support is enabled.
+	SERIAL	Serial support is enabled.
+	SMP	The kernel is an SMP kernel.
+	SPARC	Sparc architecture is enabled.
+	SWSUSP	Software suspension is enabled.
+	TS	Appropriate touchscreen support is enabled.
+	USB	USB support is enabled.
+	USBHID	USB Human Interface Device support is enabled.
+	V4L	Video For Linux support is enabled.
+	VGA	The VGA console has been enabled.
+	VT	Virtual terminal support is enabled.
+	WDT	Watchdog support is enabled.
+	XT	IBM PC/XT MFM hard disk support is enabled.
+	X86-64	X86-64 architecture is enabled.
+			More X86-64 boot options can be found in
+			Documentation/x86_64/boot-options.txt .
+
+In addition, the following text indicates that the option:
+
+	BUGS=	Relates to possible processor bugs on the said processor.
+	KNL	Is a kernel start-up parameter.
+	BOOT	Is a boot loader parameter.
+
+Parameters denoted with BOOT are actually interpreted by the boot
+loader, and have no meaning to the kernel directly.
+Do not modify the syntax of boot loader parameters without extreme
+need or coordination with <Documentation/i386/boot.txt>.
+
+Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
+a trailing = on the name of any parameter states that that parameter will
+be entered as an environment variable, whereas its absence indicates that
+it will appear as a kernel argument readable via /proc/cmdline by programs
+running once the system is up.
+
+	53c7xx=		[HW,SCSI] Amiga SCSI controllers
+			See header of drivers/scsi/53c7xx.c.
+			See also Documentation/scsi/ncr53c7xx.txt.
+
+	acpi=		[HW,ACPI] Advanced Configuration and Power Interface 
+			Format: { force | off | ht | strict }
+			force -- enable ACPI if default was off
+			off -- disable ACPI if default was on
+			noirq -- do not use ACPI for IRQ routing
+			ht -- run only enough ACPI to enable Hyper Threading
+			strict --  Be less tolerant of platforms that are not
+				strictly ACPI specification compliant.
+
+			See also Documentation/pm.txt, pci=noacpi
+
+	acpi_sleep=	[HW,ACPI] Sleep options
+			Format: { s3_bios, s3_mode }
+			See Documentation/power/video.txt
+ 
+	acpi_sci=	[HW,ACPI] ACPI System Control Interrupt trigger mode
+			Format: { level | edge |  high | low }
+
+	acpi_irq_balance	[HW,ACPI] ACPI will balance active IRQs
+				default in APIC mode
+
+	acpi_irq_nobalance	[HW,ACPI] ACPI will not move active IRQs (default)
+				default in PIC mode
+
+	acpi_irq_pci=	[HW,ACPI] If irq_balance, Clear listed IRQs for use by PCI
+			Format: <irq>,<irq>...
+
+	acpi_irq_isa=	[HW,ACPI] If irq_balance, Mark listed IRQs used by ISA
+			Format: <irq>,<irq>...
+
+	acpi_osi=	[HW,ACPI] empty param disables _OSI
+
+	acpi_serialize	[HW,ACPI] force serialization of AML methods
+
+	acpi_skip_timer_override [HW,ACPI]
+			Recognize and ignore IRQ0/pin2 Interrupt Override.
+			For broken nForce2 BIOS resulting in XT-PIC timer.
+
+	acpi_dbg_layer=	[HW,ACPI]
+			Format: <int>
+			Each bit of the <int> indicates an acpi debug layer,
+			1: enable, 0: disable. It is useful for boot time
+			debugging. After system has booted up, it can be set
+			via /proc/acpi/debug_layer.
+
+	acpi_dbg_level=	[HW,ACPI]
+			Format: <int>
+			Each bit of the <int> indicates an acpi debug level,
+			1: enable, 0: disable. It is useful for boot time
+			debugging. After system has booted up, it can be set
+			via /proc/acpi/debug_level.
+
+	acpi_fake_ecdt	[HW,ACPI] Workaround failure due to BIOS lacking ECDT
+
+	ad1816=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>
+			See also Documentation/sound/oss/AD1816.
+
+	ad1848=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>,<type>
+
+	adlib=		[HW,OSS]
+			Format: <io>
+ 
+	advansys=	[HW,SCSI]
+			See header of drivers/scsi/advansys.c.
+
+	advwdt=		[HW,WDT] Advantech WDT
+			Format: <iostart>,<iostop>
+
+	aedsp16=	[HW,OSS] Audio Excel DSP 16
+			Format: <io>,<irq>,<dma>,<mss_io>,<mpu_io>,<mpu_irq>
+			See also header of sound/oss/aedsp16.c.
+ 
+	aha152x=	[HW,SCSI]
+			See Documentation/scsi/aha152x.txt.
+
+	aha1542=	[HW,SCSI]
+			Format: <portbase>[,<buson>,<busoff>[,<dmaspeed>]]
+
+	aic7xxx=	[HW,SCSI]
+			See Documentation/scsi/aic7xxx.txt.
+
+	aic79xx=	[HW,SCSI]
+			See Documentation/scsi/aic79xx.txt.
+
+	AM53C974=	[HW,SCSI]
+			Format: <host-scsi-id>,<target-scsi-id>,<max-rate>,<max-offset>
+			See also header of drivers/scsi/AM53C974.c.
+
+	amijoy.map=	[HW,JOY] Amiga joystick support
+			Map of devices attached to JOY0DAT and JOY1DAT
+			Format: <a>,<b>
+			See also Documentation/kernel/input/joystick.txt
+
+	analog.map=	[HW,JOY] Analog joystick and gamepad support
+			Specifies type or capabilities of an analog joystick
+			connected to one of 16 gameports
+			Format: <type1>,<type2>,..<type16>
+
+	apc=		[HW,SPARC] Power management functions (SPARCstation-4/5 + deriv.)
+			Format: noidle
+			Disable APC CPU standby support. SPARCstation-Fox does
+			not play well with APC CPU idle - disable it if you have
+			APC and your system crashes randomly.
+
+	apic=		[APIC,i386] Change the output verbosity  whilst booting
+			Format: { quiet (default) | verbose | debug }
+			Change the amount of debugging information output
+			when initialising the APIC and IO-APIC components.
+ 
+	apm=		[APM] Advanced Power Management
+			See header of arch/i386/kernel/apm.c.
+
+	applicom=	[HW]
+			Format: <mem>,<irq>
+ 
+	arcrimi=	[HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
+			Format: <io>,<irq>,<nodeID>
+
+	ataflop=	[HW,M68k]
+
+	atarimouse=	[HW,MOUSE] Atari Mouse
+
+	atascsi=	[HW,SCSI] Atari SCSI
+
+	atkbd.extra=	[HW] Enable extra LEDs and keys on IBM RapidAccess,
+			EzKey and similar keyboards
+
+	atkbd.reset=	[HW] Reset keyboard during initialization
+
+	atkbd.set=	[HW] Select keyboard code set 
+			Format: <int> (2 = AT (default) 3 = PS/2)
+
+	atkbd.scroll=	[HW] Enable scroll wheel on MS Office and similar
+			keyboards
+
+	atkbd.softraw=	[HW] Choose between synthetic and real raw mode
+			Format: <bool> (0 = real, 1 = synthetic (default))
+	
+	atkbd.softrepeat=
+			[HW] Use software keyboard repeat
+
+	autotest	[IA64]
+
+	awe=		[HW,OSS] AWE32/SB32/AWE64 wave table synth
+			Format: <io>,<memsize>,<isapnp>
+ 
+	aztcd=		[HW,CD] Aztech CD268 CDROM driver
+			Format: <io>,0x79 (?)
+
+	baycom_epp=	[HW,AX25]
+			Format: <io>,<mode>
+ 
+	baycom_par=	[HW,AX25] BayCom Parallel Port AX.25 Modem
+			Format: <io>,<mode>
+			See header of drivers/net/hamradio/baycom_par.c.
+
+	baycom_ser_fdx=	[HW,AX25] BayCom Serial Port AX.25 Modem (Full Duplex Mode)
+			Format: <io>,<irq>,<mode>[,<baud>]
+			See header of drivers/net/hamradio/baycom_ser_fdx.c.
+
+	baycom_ser_hdx=	[HW,AX25] BayCom Serial Port AX.25 Modem (Half Duplex Mode)
+			Format: <io>,<irq>,<mode>
+			See header of drivers/net/hamradio/baycom_ser_hdx.c.
+
+	blkmtd_device=	[HW,MTD]
+	blkmtd_erasesz=
+	blkmtd_ro=
+	blkmtd_bs=
+	blkmtd_count=
+
+	bttv.card=	[HW,V4L] bttv (bt848 + bt878 based grabber cards)
+	bttv.radio=	Most important insmod options are available as kernel args too.
+	bttv.pll=	See Documentation/video4linux/bttv/Insmod-options
+	bttv.tuner=	and Documentation/video4linux/bttv/CARDLIST
+
+	BusLogic=	[HW,SCSI]
+			See drivers/scsi/BusLogic.c, comment before function
+			BusLogic_ParseDriverOptions().
+
+	c101=		[NET] Moxa C101 synchronous serial card
+
+	cachesize=	[BUGS=IA-32] Override level 2 CPU cache size detection.
+			Sometimes CPU hardware bugs make them report the cache
+			size incorrectly. The kernel will attempt work arounds
+			to fix known problems, but for some CPUs it is not
+			possible to determine what the correct size should be.
+			This option provides an override for these situations.
+
+	cdu31a=		[HW,CD]
+			Format: <io>,<irq>[,PAS]
+			See header of drivers/cdrom/cdu31a.c.
+
+	chandev=	[HW,NET] Generic channel device initialisation
+
+	checkreqprot	[SELINUX] Set initial checkreqprot flag value.
+			Format: { "0" | "1" }
+			See security/selinux/Kconfig help text.
+			0 -- check protection applied by kernel (includes any implied execute protection).
+			1 -- check protection requested by application.
+			Default value is set via a kernel config option.
+			Value can be changed at runtime via /selinux/checkreqprot.
+ 
+ 	clock=		[BUGS=IA-32, HW] gettimeofday timesource override. 
+			Forces specified timesource (if avaliable) to be used
+			when calculating gettimeofday(). If specicified timesource
+			is not avalible, it defaults to PIT. 
+			Format: { pit | tsc | cyclone | pmtmr }
+
+	hpet=		[IA-32,HPET] option to disable HPET and use PIT.
+			Format: disable
+
+	cm206=		[HW,CD]
+			Format: { auto | [<io>,][<irq>] }
+
+	com20020=	[HW,NET] ARCnet - COM20020 chipset
+			Format: <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
+
+	com90io=	[HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
+			Format: <io>[,<irq>]
+
+	com90xx=	[HW,NET] ARCnet - COM90xx chipset (memory-mapped buffers)
+			Format: <io>[,<irq>[,<memstart>]]
+
+	condev=		[HW,S390] console device
+	conmode=
+ 
+	console=	[KNL] Output console device and options.
+
+		tty<n>	Use the virtual console device <n>.
+
+		ttyS<n>[,options]
+			Use the specified serial port.  The options are of
+			the form "bbbbpn", where "bbbb" is the baud rate,
+			"p" is parity ("n", "o", or "e"), and "n" is bits.
+			Default is "9600n8".
+
+			See also Documentation/serial-console.txt.
+
+		uart,io,<addr>[,options]
+		uart,mmio,<addr>[,options]
+			Start an early, polled-mode console on the 8250/16550
+			UART at the specified I/O port or MMIO address,
+			switching to the matching ttyS device later.  The
+			options are the same as for ttyS, above.
+
+	cpcihp_generic=	[HW,PCI] Generic port I/O CompactPCI driver
+			Format: <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
+
+	cpia_pp=	[HW,PPT]
+			Format: { parport<nr> | auto | none }
+
+	cs4232=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
+
+	cs89x0_dma=	[HW,NET]
+			Format: <dma>
+
+	cs89x0_media=	[HW,NET]
+			Format: { rj45 | aui | bnc }
+ 
+	cyclades=	[HW,SERIAL] Cyclades multi-serial port adapter.
+ 
+	dasd=		[HW,NET]    
+			See header of drivers/s390/block/dasd_devmap.c.
+
+	db9.dev[2|3]=	[HW,JOY] Multisystem joystick support via parallel port
+			(one device per port)
+			Format: <port#>,<type>
+			See also Documentation/input/joystick-parport.txt
+
+	debug		[KNL] Enable kernel debugging (events log level).
+
+	decnet=		[HW,NET]
+			Format: <area>[,<node>]
+			See also Documentation/networking/decnet.txt.
+
+	devfs=		[DEVFS]
+			See Documentation/filesystems/devfs/boot-options.
+
+	dhash_entries=	[KNL]
+			Set number of hash buckets for dentry cache.
+ 
+	digi=		[HW,SERIAL]
+			IO parameters + enable/disable command.
+
+	digiepca=	[HW,SERIAL]
+			See drivers/char/README.epca and
+			Documentation/digiepca.txt.
+
+	dmascc=		[HW,AX25,SERIAL] AX.25 Z80SCC driver with DMA
+			support available.
+			Format: <io_dev0>[,<io_dev1>[,..<io_dev32>]]
+
+	dmasound=	[HW,OSS] Sound subsystem buffers
+
+	dscc4.setup=	[NET]
+
+	dtc3181e=	[HW,SCSI]
+
+	earlyprintk=	[IA-32, X86-64]
+			earlyprintk=vga
+			earlyprintk=serial[,ttySn[,baudrate]]
+
+			Append ,keep to not disable it when the real console
+			takes over.
+
+			Only vga or serial at a time, not both.
+
+			Currently only ttyS0 and ttyS1 are supported.
+
+			Interaction with the standard serial driver is not
+			very good.
+
+			The VGA output is eventually overwritten by the real
+			console.
+
+	eata=		[HW,SCSI]
+
+	eda=		[HW,PS2]
+
+	edb=		[HW,PS2]
+
+	edd=		[EDD]
+			Format: {"of[f]" | "sk[ipmbr]"}
+			See comment in arch/i386/boot/edd.S
+
+	eicon=		[HW,ISDN] 
+			Format: <id>,<membase>,<irq>
+
+	eisa_irq_edge=	[PARISC,HW]
+			See header of drivers/parisc/eisa.c.
+
+	elanfreq=	[IA-32]
+			See comment before function elanfreq_setup() in
+			arch/i386/kernel/cpu/cpufreq/elanfreq.c.
+
+	elevator=	[IOSCHED]
+			Format: {"as"|"cfq"|"deadline"|"noop"}
+			See Documentation/block/as-iosched.txt
+			and Documentation/block/deadline-iosched.txt for details.
+
+	enforcing	[SELINUX] Set initial enforcing status.
+			Format: {"0" | "1"}
+			See security/selinux/Kconfig help text.
+			0 -- permissive (log only, no denials).
+			1 -- enforcing (deny and log).
+			Default value is 0.
+			Value can be changed at runtime via /selinux/enforce.
+
+	es1370=		[HW,OSS]
+			Format: <lineout>[,<micbias>]
+			See also header of sound/oss/es1370.c.
+
+	es1371=		[HW,OSS]
+			Format: <spdif>,[<nomix>,[<amplifier>]]
+			See also header of sound/oss/es1371.c.
+ 
+	ether=		[HW,NET] Ethernet cards parameters
+			This option is obsoleted by the "netdev=" option, which
+			has equivalent usage. See its documentation for details.
+
+	eurwdt=		[HW,WDT] Eurotech CPU-1220/1410 onboard watchdog.
+			Format: <io>[,<irq>]
+
+	fd_mcs=		[HW,SCSI]
+			See header of drivers/scsi/fd_mcs.c.
+
+	fdomain=	[HW,SCSI]
+			See header of drivers/scsi/fdomain.c.
+
+	floppy=		[HW]
+			See Documentation/floppy.txt.
+
+	ftape=		[HW] Floppy Tape subsystem debugging options.
+			See Documentation/ftape.txt.
+
+	gamecon.map[2|3]=
+			[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
+			support via parallel port (up to 5 devices per port)
+			Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
+			See also Documentation/input/joystick-parport.txt
+
+	gamma=		[HW,DRM]
+
+	gdth=		[HW,SCSI]
+			See header of drivers/scsi/gdth.c.
+
+	gpt		[EFI] Forces disk with valid GPT signature but
+			invalid Protective MBR to be treated as GPT.
+
+	gscd=		[HW,CD]
+			Format: <io>
+
+	gt96100eth=	[NET] MIPS GT96100 Advanced Communication Controller
+
+	gus=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma16>
+ 
+	gvp11=		[HW,SCSI]
+
+	hashdist=	[KNL,NUMA] Large hashes allocated during boot
+			are distributed across NUMA nodes.  Defaults on
+			for IA-64, off otherwise.
+
+	hcl=		[IA-64] SGI's Hardware Graph compatibility layer
+
+	hd=		[EIDE] (E)IDE hard drive subsystem geometry
+			Format: <cyl>,<head>,<sect>
+
+	hd?=		[HW] (E)IDE subsystem
+	hd?lun=		See Documentation/ide.txt.
+
+	highmem=nn[KMG]	[KNL,BOOT] forces the highmem zone to have an exact
+			size of <nn>. This works even on boxes that have no
+			highmem otherwise. This also works to reduce highmem
+			size on bigger boxes.
+
+	hisax=		[HW,ISDN]
+			See Documentation/isdn/README.HiSax.
+
+	hugepages=	[HW,IA-32,IA-64] Maximal number of HugeTLB pages.
+
+	noirqbalance	[IA-32,SMP,KNL] Disable kernel irq balancing
+
+	i8042.direct	[HW] Put keyboard port into non-translated mode
+	i8042.dumbkbd	[HW] Pretend that controlled can only read data from
+			     keyboard and can not control its state
+			     (Don't attempt to blink the leds)
+	i8042.noaux	[HW] Don't check for auxiliary (== mouse) port
+	i8042.nomux	[HW] Don't check presence of an active multiplexing
+			     controller
+	i8042.nopnp	[HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
+			     controllers
+	i8042.panicblink=
+			[HW] Frequency with which keyboard LEDs should blink
+			     when kernel panics (default is 0.5 sec)
+	i8042.reset	[HW] Reset the controller during init and cleanup
+	i8042.unlock	[HW] Unlock (ignore) the keylock
+
+	i810=		[HW,DRM]
+
+	i8k.force	[HW] Activate i8k driver even if SMM BIOS signature
+			does not match list of supported models.
+	i8k.power_status
+			[HW] Report power status in /proc/i8k
+			(disabled by default)
+	i8k.restricted	[HW] Allow controlling fans only if SYS_ADMIN
+			capability is set.
+
+	ibmmcascsi=	[HW,MCA,SCSI] IBM MicroChannel SCSI adapter
+			See Documentation/mca.txt.
+
+	icn=		[HW,ISDN]
+			Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
+
+	ide=		[HW] (E)IDE subsystem
+			Format: ide=nodma or ide=doubler or ide=reverse
+			See Documentation/ide.txt.
+
+	ide?=		[HW] (E)IDE subsystem
+			Format: ide?=noprobe or chipset specific parameters.
+			See Documentation/ide.txt.
+	
+	idebus=		[HW] (E)IDE subsystem - VLB/PCI bus speed
+			See Documentation/ide.txt.
+
+	idle=		[HW]
+			Format: idle=poll or idle=halt
+ 
+	ihash_entries=	[KNL]
+			Set number of hash buckets for inode cache.
+
+	in2000=		[HW,SCSI]
+			See header of drivers/scsi/in2000.c.
+
+	init=		[KNL]
+			Format: <full_path>
+			Run specified binary instead of /sbin/init as init
+			process.
+
+	initcall_debug	[KNL] Trace initcalls as they are executed.  Useful
+			for working out where the kernel is dying during
+			startup.
+
+	initrd=		[BOOT] Specify the location of the initial ramdisk
+
+	inport.irq=	[HW] Inport (ATI XL and Microsoft) busmouse driver
+			Format: <irq>
+
+	inttest=	[IA64]
+
+	io7=		[HW] IO7 for Marvel based alpha systems
+			See comment before marvel_specify_io7 in
+			arch/alpha/kernel/core_marvel.c.
+
+	ip=		[IP_PNP]
+			See Documentation/nfsroot.txt.
+
+	ip2=		[HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
+			See comment before ip2_setup() in drivers/char/ip2.c.
+
+	ips=		[HW,SCSI] Adaptec / IBM ServeRAID controller
+			See header of drivers/scsi/ips.c.
+
+	isapnp=		[ISAPNP]
+			Format: <RDP>, <reset>, <pci_scan>, <verbosity>
+
+	isolcpus=	[KNL,SMP] Isolate CPUs from the general scheduler.
+			Format: <cpu number>,...,<cpu number>
+			This option can be used to specify one or more CPUs
+			to isolate from the general SMP balancing and scheduling
+			algorithms. The only way to move a process onto or off
+			an "isolated" CPU is via the CPU affinity syscalls.
+			<cpu number> begins at 0 and the maximum value is
+			"number of CPUs in system - 1".
+
+			This option is the preferred way to isolate CPUs. The
+			alternative - manually setting the CPU mask of all tasks
+			in the system can cause problems and suboptimal load
+			balancer performance.
+
+	isp16=		[HW,CD]
+			Format: <io>,<irq>,<dma>,<setup>
+
+	iucv=		[HW,NET] 
+
+	js=		[HW,JOY] Analog joystick
+			See Documentation/input/joystick.txt.
+
+	keepinitrd	[HW,ARM]
+
+	kstack=N	[IA-32, X86-64] Print N words from the kernel stack
+			in oops dumps.
+
+	l2cr=		[PPC]
+
+	lapic		[IA-32,APIC] Enable the local APIC even if BIOS disabled it.
+
+	lasi=		[HW,SCSI] PARISC LASI driver for the 53c700 chip
+			Format: addr:<io>,irq:<irq>
+
+	llsc*=		[IA64]
+			See function print_params() in arch/ia64/sn/kernel/llsc4.c.
+
+	load_ramdisk=	[RAM] List of ramdisks to load from floppy
+			See Documentation/ramdisk.txt.
+
+	lockd.udpport=	[NFS]
+
+	lockd.tcpport=	[NFS]
+
+	logibm.irq=	[HW,MOUSE] Logitech Bus Mouse Driver
+			Format: <irq>
+
+	loglevel=	All Kernel Messages with a loglevel smaller than the
+			console loglevel will be printed to the console. It can
+			also be changed with klogd or other programs. The
+			loglevels are defined as follows:
+
+			0 (KERN_EMERG)		system is unusable
+			1 (KERN_ALERT)		action must be taken immediately
+			2 (KERN_CRIT)		critical conditions
+			3 (KERN_ERR)		error conditions
+			4 (KERN_WARNING)	warning conditions
+			5 (KERN_NOTICE)		normal but significant condition
+			6 (KERN_INFO)		informational
+			7 (KERN_DEBUG)		debug-level messages
+
+	log_buf_len=n	Sets the size of the printk ring buffer, in bytes.
+			Format is n, nk, nM.  n must be a power of two.  The
+			default is set in kernel config.
+
+	lp=0		[LP]	Specify parallel ports to use, e.g,
+	lp=port[,port...]	lp=none,parport0 (lp0 not configured, lp1 uses
+	lp=reset		first parallel port). 'lp=0' disables the
+	lp=auto			printer driver. 'lp=reset' (which can be
+				specified in addition to the ports) causes
+				attached printers to be reset. Using
+				lp=port1,port2,... specifies the parallel ports
+				to associate lp devices with, starting with
+				lp0. A port specification may be 'none' to skip
+				that lp device, or a parport name such as
+				'parport0'. Specifying 'lp=auto' instead of a
+				port specification list means that device IDs
+				from each port should be examined, to see if
+				an IEEE 1284-compliant printer is attached; if
+				so, the driver will manage that printer.
+				See also header of drivers/char/lp.c.
+
+	lpj=n		[KNL]
+			Sets loops_per_jiffy to given constant, thus avoiding
+			time-consuming boot-time autodetection (up to 250 ms per
+			CPU). 0 enables autodetection (default). To determine
+			the correct value for your kernel, boot with normal
+			autodetection and see what value is printed. Note that
+			on SMP systems the preset will be applied to all CPUs,
+			which is likely to cause problems if your CPUs need
+			significantly divergent settings. An incorrect value
+			will cause delays in the kernel to be wrong, leading to
+			unpredictable I/O errors and other breakage. Although
+			unlikely, in the extreme case this might damage your
+			hardware.
+
+	ltpc=		[NET]
+			Format: <io>,<irq>,<dma>
+
+	mac5380=	[HW,SCSI]
+			Format: <can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
+
+	mac53c9x=	[HW,SCSI]
+			Format: <num_esps>,<disconnect>,<nosync>,<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
+
+	machvec=	[IA64]
+			Force the use of a particular machine-vector (machvec) in a generic
+			kernel.  Example: machvec=hpzx1_swiotlb
+
+	mad16=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma16>,<mpu_io>,<mpu_irq>,<joystick>
+
+	maui=		[HW,OSS]
+			Format: <io>,<irq>
+ 
+	max_loop=       [LOOP] Maximum number of loopback devices that can
+			be mounted
+			Format: <1-256>
+
+	maxcpus=	[SMP] Maximum number of processors that	an SMP kernel
+			should make use of
+
+	max_luns=	[SCSI] Maximum number of LUNs to probe
+			Should be between 1 and 2^32-1.
+
+	max_report_luns=
+			[SCSI] Maximum number of LUNs received
+			Should be between 1 and 16384.
+
+	mca-pentium	[BUGS=IA-32]
+
+	mcatest=	[IA-64]
+
+	mcd=		[HW,CD]
+			Format: <port>,<irq>,<mitsumi_bug_93_wait>
+
+	mcdx=		[HW,CD]
+
+	mce		[IA-32] Machine Check Exception
+
+	md=		[HW] RAID subsystems devices and level
+			See Documentation/md.txt.
+ 
+	mdacon=		[MDA]
+			Format: <first>,<last>
+			Specifies range of consoles to be captured by the MDA.
+ 
+	mem=nn[KMG]	[KNL,BOOT] Force usage of a specific amount of memory
+			Amount of memory to be used when the kernel is not able
+			to see the whole system memory or for test.
+			[IA-32] Use together with memmap= to avoid physical
+			address space collisions. Without memmap= PCI devices
+			could be placed at addresses belonging to unused RAM.
+
+	mem=nopentium	[BUGS=IA-32] Disable usage of 4MB pages for kernel
+			memory.
+
+	memmap=exactmap	[KNL,IA-32] Enable setting of an exact
+			E820 memory map, as specified by the user.
+			Such memmap=exactmap lines can be constructed based on
+			BIOS output or other requirements. See the memmap=nn@ss
+			option description.
+
+	memmap=nn[KMG]@ss[KMG]
+			[KNL] Force usage of a specific region of memory
+			Region of memory to be used, from ss to ss+nn.
+
+	memmap=nn[KMG]#ss[KMG]
+			[KNL,ACPI] Mark specific memory as ACPI data.
+			Region of memory to be used, from ss to ss+nn.
+
+	memmap=nn[KMG]$ss[KMG]
+			[KNL,ACPI] Mark specific memory as reserved.
+			Region of memory to be used, from ss to ss+nn.
+
+	meye.*=		[HW] Set MotionEye Camera parameters
+			See Documentation/video4linux/meye.txt.
+
+	mga=		[HW,DRM]
+
+	mousedev.tap_time=
+			[MOUSE] Maximum time between finger touching and
+			leaving touchpad surface for touch to be considered
+			a tap and be reported as a left button click (for
+			touchpads working in absolute mode only).
+			Format: <msecs>
+	mousedev.xres=	[MOUSE] Horizontal screen resolution, used for devices
+			reporting absolute coordinates, such as tablets
+	mousedev.yres=	[MOUSE] Vertical screen resolution, used for devices
+			reporting absolute coordinates, such as tablets
+
+	mpu401=		[HW,OSS]
+			Format: <io>,<irq>
+
+	MTD_Partition=	[MTD]
+			Format: <name>,<region-number>,<size>,<offset>
+
+	MTD_Region=	[MTD]
+			Format: <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
+
+	mtdparts=	[MTD]
+			See drivers/mtd/cmdline.c.
+
+	mtouchusb.raw_coordinates=
+			[HW] Make the MicroTouch USB driver use raw coordinates ('y', default)
+			or cooked coordinates ('n')
+
+	n2=		[NET] SDL Inc. RISCom/N2 synchronous serial card
+
+	NCR_D700=	[HW,SCSI]
+			See header of drivers/scsi/NCR_D700.c.
+
+	ncr5380=	[HW,SCSI]
+
+	ncr53c400=	[HW,SCSI]
+
+	ncr53c400a=	[HW,SCSI]
+
+	ncr53c406a=	[HW,SCSI]
+
+	ncr53c8xx=	[HW,SCSI]
+
+	netdev=		[NET] Network devices parameters
+			Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
+			Note that mem_start is often overloaded to mean
+			something different and driver-specific.
+ 
+	nfsaddrs=	[NFS]
+			See Documentation/nfsroot.txt.
+
+	nfsroot=	[NFS] nfs root filesystem for disk-less boxes.
+			See Documentation/nfsroot.txt.
+
+	nmi_watchdog=	[KNL,BUGS=IA-32] Debugging features for SMP kernels
+
+	no387		[BUGS=IA-32] Tells the kernel to use the 387 maths
+			emulation library even if a 387 maths coprocessor
+			is present.
+
+	noalign		[KNL,ARM] 
+ 
+	noapic		[SMP,APIC] Tells the kernel to not make use of any
+			IOAPICs that may be present in the system.
+
+	noasync		[HW,M68K] Disables async and sync negotiation for
+			all devices.
+
+	nobats		[PPC] Do not use BATs for mapping kernel lowmem
+			on "Classic" PPC cores.
+
+	nocache		[ARM]
+ 
+	nodisconnect	[HW,SCSI,M68K] Disables SCSI disconnects.
+
+	noexec		[IA-64]
+
+	noexec		[IA-32, X86-64]
+			noexec=on: enable non-executable mappings (default)
+			noexec=off: disable nn-executable mappings
+
+	nofxsr		[BUGS=IA-32]
+
+	nohlt		[BUGS=ARM]
+ 
+	no-hlt		[BUGS=IA-32] Tells the kernel that the hlt
+			instruction doesn't work correctly and not to
+			use it.
+
+	nohalt		[IA-64] Tells the kernel not to use the power saving
+			function PAL_HALT_LIGHT when idle. This increases
+			power-consumption. On the positive side, it reduces
+			interrupt wake-up latency, which may improve performance
+			in certain environments such as networked servers or
+			real-time systems.
+
+	noirqdebug	[IA-32] Disables the code which attempts to detect and
+			disable unhandled interrupt sources.
+
+	noisapnp	[ISAPNP] Disables ISA PnP code.
+
+	noinitrd	[RAM] Tells the kernel not to load any configured
+			initial RAM disk.
+
+	nointroute	[IA-64]
+
+	nolapic		[IA-32,APIC] Do not enable or use the local APIC.
+
+	noltlbs		[PPC] Do not use large page/tlb entries for kernel
+			lowmem mapping on PPC40x.
+
+	nomce		[IA-32] Machine Check Exception
+
+	noresidual	[PPC] Don't use residual data on PReP machines.
+
+	noresume	[SWSUSP] Disables resume and restore original swap space.
+ 
+	no-scroll	[VGA] Disables scrollback.
+			This is required for the Braillex ib80-piezo Braille
+			reader made by F.H. Papenmeier (Germany).
+
+	nosbagart	[IA-64]
+
+	nosmp		[SMP] Tells an SMP kernel to act as a UP kernel.
+
+	nosync		[HW,M68K] Disables sync negotiation for all devices.
+
+	notsc		[BUGS=IA-32] Disable Time Stamp Counter
+
+	nousb		[USB] Disable the USB subsystem
+
+	nowb		[ARM]
+ 
+	opl3=		[HW,OSS]
+			Format: <io>
+
+	opl3sa=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>,<mpu_io>,<mpu_irq>
+
+	opl3sa2=	[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>,<mss_io>,<mpu_io>,<ymode>,<loopback>[,<isapnp>,<multiple]
+ 
+	oprofile.timer=	[HW]
+			Use timer interrupt instead of performance counters
+
+	optcd=		[HW,CD]
+			Format: <io>
+
+	osst=		[HW,SCSI] SCSI Tape Driver
+			Format: <buffer_size>,<write_threshold>
+			See also Documentation/scsi/st.txt.
+
+	panic=		[KNL] Kernel behaviour on panic
+			Format: <timeout>
+
+	parkbd.port=	[HW] Parallel port number the keyboard adapter is
+			connected to, default is 0.
+			Format: <parport#>
+	parkbd.mode=	[HW] Parallel port keyboard adapter mode of operation,
+			0 for XT, 1 for AT (default is AT).
+			Format: <mode> 
+
+	parport=0	[HW,PPT]	Specify parallel ports. 0 disables.
+	parport=auto			Use 'auto' to force the driver to use
+	parport=0xBBB[,IRQ[,DMA]]	any IRQ/DMA settings detected (the
+					default is to ignore detected IRQ/DMA
+					settings because of possible
+					conflicts). You can specify the base
+					address, IRQ, and DMA settings; IRQ and
+					DMA should be numbers, or 'auto' (for
+					using detected settings on that
+					particular port), or 'nofifo' (to avoid
+					using a FIFO even if it is detected).
+					Parallel ports are assigned in the
+					order they are specified on the command
+					line, starting with parport0.
+
+	parport_init_mode=
+			[HW,PPT]	Configure VIA parallel port to
+					operate in specific mode. This is
+					necessary on Pegasos computer where
+					firmware has no options for setting up
+					parallel port mode and sets it to
+					spp. Currently this function knows
+					686a and 8231 chips.
+			Format: [spp|ps2|epp|ecp|ecpepp]
+
+	pas2=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma16>,<sb_io>,<sb_irq>,<sb_dma>,<sb_dma16>
+ 
+	pas16=		[HW,SCSI]
+			See header of drivers/scsi/pas16.c.
+
+	pcbit=		[HW,ISDN]
+
+	pcd.		[PARIDE]
+			See header of drivers/block/paride/pcd.c.
+			See also Documentation/paride.txt.
+
+	pci=option[,option...]		[PCI] various PCI subsystem options:
+		off			[IA-32] don't probe for the PCI bus
+		bios			[IA-32] force use of PCI BIOS, don't access
+					the hardware directly. Use this if your machine
+					has a non-standard PCI host bridge.
+		nobios			[IA-32] disallow use of PCI BIOS, only direct
+					hardware access methods are allowed. Use this
+					if you experience crashes upon bootup and you
+					suspect they are caused by the BIOS.
+		conf1			[IA-32] Force use of PCI Configuration Mechanism 1.
+		conf2			[IA-32] Force use of PCI Configuration Mechanism 2.
+		nosort			[IA-32] Don't sort PCI devices according to
+					order given by the PCI BIOS. This sorting is done
+					to get a device order compatible with older kernels.
+		biosirq			[IA-32] Use PCI BIOS calls to get the interrupt
+					routing table. These calls are known to be buggy
+					on several machines and they hang the machine when used,
+					but on other computers it's the only way to get the
+					interrupt routing table. Try this option if the kernel
+					is unable to allocate IRQs or discover secondary PCI
+					buses on your motherboard.
+		rom			[IA-32] Assign address space to expansion ROMs.
+					Use with caution as certain devices share address
+					decoders between ROMs and other resources.
+		irqmask=0xMMMM		[IA-32] Set a bit mask of IRQs allowed to be assigned
+					automatically to PCI devices. You can make the kernel
+					exclude IRQs of your ISA cards this way.
+		lastbus=N		[IA-32] Scan all buses till bus #N. Can be useful
+					if the kernel is unable to find your secondary buses
+					and you want to tell it explicitly which ones they are.
+		assign-busses		[IA-32] Always assign all PCI bus
+					numbers ourselves, overriding
+					whatever the firmware may have
+					done.
+		usepirqmask		[IA-32] Honor the possible IRQ mask
+					stored in the BIOS $PIR table. This is
+					needed on some systems with broken
+					BIOSes, notably some HP Pavilion N5400
+					and Omnibook XE3 notebooks. This will
+					have no effect if ACPI IRQ routing is
+					enabled.
+		noacpi			[IA-32] Do not use ACPI for IRQ routing
+					or for PCI scanning.
+		routeirq		Do IRQ routing for all PCI devices.
+					This is normally done in pci_enable_device(),
+					so this option is a temporary workaround
+					for broken drivers that don't call it.
+
+		firmware		[ARM] Do not re-enumerate the bus but
+					instead just use the configuration
+					from the bootloader. This is currently
+					used on IXP2000 systems where the
+					bus has to be configured a certain way
+					for adjunct CPUs.
+
+	pcmv=		[HW,PCMCIA] BadgePAD 4
+
+	pd.		[PARIDE]
+			See Documentation/paride.txt.
+
+	pdcchassis=	[PARISC,HW] Disable/Enable PDC Chassis Status codes at
+			boot time.
+			Format: { 0 | 1 }
+			See arch/parisc/kernel/pdc_chassis.c
+
+	pf.		[PARIDE]
+			See Documentation/paride.txt.
+
+	pg.		[PARIDE]
+			See Documentation/paride.txt.
+
+	pirq=		[SMP,APIC] Manual mp-table setup
+			See Documentation/i386/IO-APIC.txt.
+
+	plip=		[PPT,NET] Parallel port network link
+			Format: { parport<nr> | timid | 0 }
+			See also Documentation/parport.txt.
+
+	pnpacpi=	[ACPI]
+			{ off }
+
+	pnpbios=	[ISAPNP]
+			{ on | off | curr | res | no-curr | no-res }
+
+	pnp_reserve_irq=
+			[ISAPNP] Exclude IRQs for the autoconfiguration
+
+	pnp_reserve_dma=
+			[ISAPNP] Exclude DMAs for the autoconfiguration
+
+	pnp_reserve_io=	[ISAPNP] Exclude I/O ports for the autoconfiguration
+		     	Ranges are in pairs (I/O port base and size).
+
+	pnp_reserve_mem=
+			[ISAPNP] Exclude memory regions for the autoconfiguration
+			Ranges are in pairs (memory base and size).
+
+	profile=	[KNL] Enable kernel profiling via /proc/profile
+			{ schedule | <number> }
+			(param: schedule - profile schedule points}
+			(param: profile step/bucket size as a power of 2 for
+				statistical time based profiling)
+
+	processor.max_cstate=   [HW, ACPI]
+			Limit processor to maximum C-state
+			max_cstate=9 overrides any DMI blacklist limit.
+
+	prompt_ramdisk=	[RAM] List of RAM disks to prompt for floppy disk
+			before loading.
+			See Documentation/ramdisk.txt.
+
+	psmouse.proto=  [HW,MOUSE] Highest PS2 mouse protocol extension to
+			probe for (bare|imps|exps).
+	psmouse.rate=	[HW,MOUSE] Set desired mouse report rate, in reports
+			per second.
+	psmouse.resetafter=
+			[HW,MOUSE] Try to reset the device after so many bad packets
+			(0 = never).
+	psmouse.resolution=
+			[HW,MOUSE] Set desired mouse resolution, in dpi.
+	psmouse.smartscroll=
+			[HW,MOUSE] Controls Logitech smartscroll autorepeat,
+			0 = disabled, 1 = enabled (default).
+
+	pss=		[HW,OSS] Personal Sound System (ECHO ESC614)
+			Format: <io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq>
+
+	pt.		[PARIDE]
+			See Documentation/paride.txt.
+
+	quiet=		[KNL] Disable log messages
+ 
+	r128=		[HW,DRM]
+
+	raid=		[HW,RAID]
+			See Documentation/md.txt.
+
+	ramdisk=	[RAM] Sizes of RAM disks in kilobytes [deprecated]
+			See Documentation/ramdisk.txt.
+
+	ramdisk_blocksize=
+			[RAM]
+			See Documentation/ramdisk.txt.
+ 
+	ramdisk_size=	[RAM] Sizes of RAM disks in kilobytes
+			New name for the ramdisk parameter.
+			See Documentation/ramdisk.txt.
+
+	reboot=		[BUGS=IA-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
+			Format: <reboot_mode>[,<reboot_mode2>[,...]]
+			See arch/*/kernel/reboot.c.
+
+	reserve=	[KNL,BUGS] Force the kernel to ignore some iomem area
+
+	resume=		[SWSUSP] Specify the partition device for software suspension
+
+	rhash_entries=	[KNL,NET]
+			Set number of hash buckets for route cache
+
+	riscom8=	[HW,SERIAL]
+			Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
+
+	ro		[KNL] Mount root device read-only on boot
+
+	root=		[KNL] Root filesystem
+
+	rootdelay=	[KNL] Delay (in seconds) to pause before attempting to
+			mount the root filesystem
+
+	rootflags=	[KNL] Set root filesystem mount option string
+
+	rootfstype=	[KNL] Set root filesystem type
+
+	rw		[KNL] Mount root device read-write on boot
+
+	S		[KNL] Run init in single mode
+
+	sa1100ir	[NET]
+			See drivers/net/irda/sa1100_ir.c.
+
+	sb=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>
+
+	sbni=		[NET] Granch SBNI12 leased line adapter
+ 
+	sbpcd=		[HW,CD] Soundblaster CD adapter
+			Format: <io>,<type>
+			See a comment before function sbpcd_setup() in
+			drivers/cdrom/sbpcd.c.
+
+	sc1200wdt=	[HW,WDT] SC1200 WDT (watchdog) driver
+			Format: <io>[,<timeout>[,<isapnp>]]
+
+	scsi_debug_*=	[SCSI]
+			See drivers/scsi/scsi_debug.c.
+
+	scsi_default_dev_flags=
+			[SCSI] SCSI default device flags
+			Format: <integer>
+
+	scsi_dev_flags=	[SCSI] Black/white list entry for vendor and model
+			Format: <vendor>:<model>:<flags>
+			(flags are integer value)
+
+	scsi_logging=	[SCSI]
+
+	selinux		[SELINUX] Disable or enable SELinux at boot time.
+			Format: { "0" | "1" }
+			See security/selinux/Kconfig help text.
+			0 -- disable.
+			1 -- enable.
+			Default value is set via kernel config option.
+			If enabled at boot time, /selinux/disable can be used
+			later to disable prior to initial policy load.
+
+	serialnumber	[BUGS=IA-32]
+
+	sg_def_reserved_size=
+			[SCSI]
+ 
+	sgalaxy=	[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>,<sgbase>
+
+	shapers=	[NET]
+			Maximal number of shapers.
+ 
+	sim710=		[SCSI,HW]
+			See header of drivers/scsi/sim710.c.
+
+	simeth=		[IA-64]
+	simscsi=
+ 
+	sjcd=		[HW,CD]
+			Format: <io>,<irq>,<dma>
+			See header of drivers/cdrom/sjcd.c.
+
+	slram=		[HW,MTD]
+
+	smart2=		[HW]
+			Format: <io1>[,<io2>[,...,<io8>]]
+
+	snd-ad1816a=	[HW,ALSA]
+
+	snd-ad1848=	[HW,ALSA]
+
+	snd-ali5451=	[HW,ALSA]
+
+	snd-als100=	[HW,ALSA]
+
+	snd-als4000=	[HW,ALSA]
+
+	snd-azt2320=	[HW,ALSA]
+
+	snd-cmi8330=	[HW,ALSA]
+
+	snd-cmipci=	[HW,ALSA]
+
+	snd-cs4231=	[HW,ALSA]
+
+	snd-cs4232=	[HW,ALSA]
+
+	snd-cs4236=	[HW,ALSA]
+
+	snd-cs4281=	[HW,ALSA]
+
+	snd-cs46xx=	[HW,ALSA]
+
+	snd-dt019x=	[HW,ALSA]
+
+	snd-dummy=	[HW,ALSA]
+
+	snd-emu10k1=	[HW,ALSA]
+
+	snd-ens1370=	[HW,ALSA]
+
+	snd-ens1371=	[HW,ALSA]
+
+	snd-es968=	[HW,ALSA]
+
+	snd-es1688=	[HW,ALSA]
+
+	snd-es18xx=	[HW,ALSA]
+
+	snd-es1938=	[HW,ALSA]
+
+	snd-es1968=	[HW,ALSA]
+
+	snd-fm801=	[HW,ALSA]
+
+	snd-gusclassic=	[HW,ALSA]
+
+	snd-gusextreme=	[HW,ALSA]
+
+	snd-gusmax=	[HW,ALSA]
+
+	snd-hdsp=	[HW,ALSA]
+
+	snd-ice1712=	[HW,ALSA]
+
+	snd-intel8x0=	[HW,ALSA]
+
+	snd-interwave=	[HW,ALSA]
+
+	snd-interwave-stb=
+			[HW,ALSA]
+
+	snd-korg1212=	[HW,ALSA]
+
+	snd-maestro3=	[HW,ALSA]
+
+	snd-mpu401=	[HW,ALSA]
+
+	snd-mtpav=	[HW,ALSA]
+
+	snd-nm256=	[HW,ALSA]
+
+	snd-opl3sa2=	[HW,ALSA]
+
+	snd-opti92x-ad1848=
+			[HW,ALSA]
+
+	snd-opti92x-cs4231=
+			[HW,ALSA]
+
+	snd-opti93x=	[HW,ALSA]
+
+	snd-pmac=	[HW,ALSA]
+
+	snd-rme32=	[HW,ALSA]
+
+	snd-rme96=	[HW,ALSA]
+
+	snd-rme9652=	[HW,ALSA]
+
+	snd-sb8=	[HW,ALSA]
+
+	snd-sb16=	[HW,ALSA]
+
+	snd-sbawe=	[HW,ALSA]
+
+	snd-serial=	[HW,ALSA]
+
+	snd-sgalaxy=	[HW,ALSA]
+
+	snd-sonicvibes=	[HW,ALSA]
+
+	snd-sun-amd7930=
+			[HW,ALSA]
+
+	snd-sun-cs4231=	[HW,ALSA]
+
+	snd-trident=	[HW,ALSA]
+
+	snd-usb-audio=	[HW,ALSA,USB]
+
+	snd-via82xx=	[HW,ALSA]
+
+	snd-virmidi=	[HW,ALSA]
+
+	snd-wavefront=	[HW,ALSA]
+
+	snd-ymfpci=	[HW,ALSA]
+ 
+	sonicvibes=	[HW,OSS]
+			Format: <reverb>
+ 
+	sonycd535=	[HW,CD]
+			Format: <io>[,<irq>]
+
+	sonypi.*=	[HW] Sony Programmable I/O Control Device driver
+			See Documentation/sonypi.txt
+
+	specialix=	[HW,SERIAL] Specialix multi-serial port adapter
+			See Documentation/specialix.txt.
+
+	spia_io_base=	[HW,MTD]
+	spia_fio_base=
+	spia_pedr=
+	spia_peddr=
+
+	sscape=		[HW,OSS]
+			Format: <io>,<irq>,<dma>,<mpu_io>,<mpu_irq>
+ 
+	st=		[HW,SCSI] SCSI tape parameters (buffers, etc.)
+			See Documentation/scsi/st.txt.
+
+	st0x=		[HW,SCSI]
+			See header of drivers/scsi/seagate.c.
+
+	sti=		[PARISC,HW]
+			Format: <num>
+			Set the STI (builtin display/keyboard on the HP-PARISC
+			machines) console (graphic card) which should be used
+			as the initial boot-console.
+			See also comment in drivers/video/console/sticore.c.
+
+	sti_font=	[HW]
+			See comment in drivers/video/console/sticore.c.
+
+	stifb=		[HW]
+			Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
+
+	stram_swap=	[HW,M68k]
+
+	swiotlb=	[IA-64] Number of I/O TLB slabs
+ 
+	switches=	[HW,M68k]
+
+	sym53c416=	[HW,SCSI]
+			See header of drivers/scsi/sym53c416.c.
+
+	t128=		[HW,SCSI]
+			See header of drivers/scsi/t128.c.
+
+	tdfx=		[HW,DRM]
+
+	thash_entries=	[KNL,NET]
+			Set number of hash buckets for TCP connection
+
+	time		Show timing data prefixed to each printk message line
+
+	tipar.timeout=	[HW,PPT]
+			Set communications timeout in tenths of a second
+			(default 15).
+
+	tipar.delay=	[HW,PPT]
+			Set inter-bit delay in microseconds (default 10).
+
+	tmc8xx=		[HW,SCSI]
+			See header of drivers/scsi/seagate.c.
+
+	tmscsim=	[HW,SCSI]
+			See comment before function dc390_setup() in
+			drivers/scsi/tmscsim.c.
+
+	tp720=		[HW,PS2]
+
+	trix=		[HW,OSS] MediaTrix AudioTrix Pro
+			Format: <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
+ 
+	tsdev.xres=	[TS] Horizontal screen resolution.
+	tsdev.yres=	[TS] Vertical screen resolution.
+
+	turbografx.map[2|3]=
+			[HW,JOY] TurboGraFX parallel port interface
+			Format: <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
+			See also Documentation/input/joystick-parport.txt
+
+	u14-34f=	[HW,SCSI] UltraStor 14F/34F SCSI host adapter
+			See header of drivers/scsi/u14-34f.c.
+
+	uart401=	[HW,OSS]
+			Format: <io>,<irq>
+
+	uart6850=	[HW,OSS]
+			Format: <io>,<irq>
+
+	usb-handoff	[HW] Enable early USB BIOS -> OS handoff
+
+	usbhid.mousepoll=
+			[USBHID] The interval which mice are to be polled at.
+ 
+	video=		[FB] Frame buffer configuration
+			See Documentation/fb/modedb.txt.
+
+	vga=		[BOOT,IA-32] Select a particular video mode
+			See Documentation/i386/boot.txt and Documentation/svga.txt.
+			Use vga=ask for menu.
+			This is actually a boot loader parameter; the value is
+			passed to the kernel using a special protocol.
+
+	vmalloc=nn[KMG]	[KNL,BOOT] forces the vmalloc area to have an exact
+			size of <nn>. This can be used to increase the
+			minimum size (128MB on x86). It can also be used to
+			decrease the size and leave more room for directly
+			mapped kernel RAM.
+
+	vmhalt=		[KNL,S390]
+
+	vmpoff=		[KNL,S390] 
+ 
+	waveartist=	[HW,OSS]
+			Format: <io>,<irq>,<dma>,<dma2>
+ 
+	wd33c93=	[HW,SCSI]
+			See header of drivers/scsi/wd33c93.c.
+
+	wd7000=		[HW,SCSI]
+			See header of drivers/scsi/wd7000.c.
+
+	wdt=		[WDT] Watchdog
+			See Documentation/watchdog/watchdog.txt.
+
+	xd=		[HW,XT] Original XT pre-IDE (RLL encoded) disks.
+	xd_geo=		See header of drivers/block/xd.c.
+
+	xirc2ps_cs=	[NET,PCMCIA]
+			Format: <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+
+
+Changelog:
+
+	The last known update (for 2.4.0) - the changelog was not kept before.
+	2000-06-??	Mr. Unknown
+
+	Update for 2.5.49, description for most of the options introduced,
+	references to other documentation (C files, READMEs, ..), added S390,
+	PPC, SPARC, MTD, ALSA and OSS category. Minor corrections and
+	reformatting.
+	2002-11-24	Petr Baudis <pasky@ucw.cz>
+			Randy Dunlap <randy.dunlap@verizon.net>
+
+TODO:
+
+	Add documentation for ALSA options.
+	Add more DRM drivers.