Merge tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds

Pull LED updates from Lee Jones:
 "New Drivers:
   - Add support for MediaTek MT6370 LED Indicator
   - Add support for MediaTek MT6370 Flashlight
   - Add support for QCOM PMIC Flash
   - Add support for Rohm BD2606MVV Charge Pump LED

  New Device Support:
   - Add support for PMK8550 PWM to QCOM LPG

  New Functionality:
   - Add support for high resolution PWM to QCOM LPG

  Fix-ups:
   - Kconfig 'depends' and 'select' dependency changes
   - Remove unused / irrelevant includes
   - Remove unnecessary checks (already performed further into the call stack)
   - Trivial: Fix commentary, simplify error messages
   - Rid 'defined but not used' warnings
   - Provide documentation
   - Explicitly provide include files

  Bug Fixes:
   - Mark GPIO LED as BROKEN
   - Fix Kconfig entries
   - Fix various Smatch staticify reports
   - Fix error handling (or a lack there of)"

* tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (30 commits)
  leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
  dt-bindings: leds: Add ROHM BD2606MVV LED
  docs: leds: ledtrig-oneshot: Fix spelling mistake
  leds: pwm-multicolor: Simplify an error message
  dt-bindings: leds: Convert PCA9532 to dtschema
  leds: rgb: leds-qcom-lpg: Add support for PMK8550 PWM
  leds: rgb: leds-qcom-lpg: Add support for high resolution PWM
  dt-bindings: leds-qcom-lpg: Add qcom,pmk8550-pwm compatible string
  leds: tca6507: Fix error handling of using fwnode_property_read_string
  leds: flash: Set variables mvflash_{3,4}ch_regs storage-class-specifier to static
  leds: rgb: mt6370: Correct config name to select in LEDS_MT6370_RGB
  MAINTAINERS: Add entry for LED devices documentation
  Documentation: leds: MT6370: Use bullet lists for timing variables
  Documentation: leds: mt6370: Properly wrap hw_pattern chart
  Documentation: leds: Add MT6370 doc to the toctree
  leds: rgb: mt6370: Fix implicit declaration for FIELD_GET
  docs: leds: Add MT6370 RGB LED pattern document
  leds: flash: mt6370: Add MediaTek MT6370 flashlight support
  leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support
  dt-bindings: leds: spmi-flash-led: Add pm6150l compatible
  ...

3 files changed, 66 insertions, 1 deletions

diff --git a/Documentation/leds/index.rst b/Documentation/leds/index.rst
index b9ca081fac71..ce57254cb871 100644
--- a/Documentation/leds/index.rst
+++ b/Documentation/leds/index.rst
@@ -25,5 +25,6 @@ LEDs
    leds-lp5562
    leds-lp55xx
    leds-mlxcpld
+   leds-mt6370-rgb
    leds-sc27xx
    leds-qcom-lpg
diff --git a/Documentation/leds/leds-mt6370-rgb.rst b/Documentation/leds/leds-mt6370-rgb.rst
new file mode 100644
index 000000000000..152a2e592172
--- /dev/null
+++ b/Documentation/leds/leds-mt6370-rgb.rst
@@ -0,0 +1,64 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================================
+The device for Mediatek MT6370 RGB LED
+=========================================
+
+Description
+-----------
+
+The MT6370 integrates a four-channel RGB LED driver, designed to provide a
+variety of lighting effect for mobile device applications. The RGB LED devices
+includes a smart LED string controller and it can drive 3 channels of LEDs with
+a sink current up to 24mA and a CHG_VIN power good indicator LED with sink
+current up to 6mA. It provides three operation modes for RGB LEDs:
+PWM Dimming mode, breath pattern mode, and constant current mode. The device
+can increase or decrease the brightness of the RGB LED via an I2C interface.
+
+The breath pattern for a channel can be programmed using the "pattern" trigger,
+using the hw_pattern attribute.
+
+/sys/class/leds/<led>/hw_pattern
+--------------------------------
+
+Specify a hardware breath pattern for a MT6370 RGB LED.
+
+The breath pattern is a series of timing pairs, with the hold-time expressed in
+milliseconds. And the brightness is controlled by
+'/sys/class/leds/<led>/brightness'. The pattern doesn't include the brightness
+setting. Hardware pattern only controls the timing for each pattern stage
+depending on the current brightness setting.
+
+Pattern diagram::
+
+         "0 Tr1 0 Tr2 0 Tf1 0 Tf2 0 Ton 0 Toff" --> '0' for dummy brightness code
+
+          ^
+          |           ============
+          |          /            \                                /
+    Icurr |         /              \                              /
+          |        /                \                            /
+          |       /                  \                          /   .....repeat
+          |      /                    \                        /
+          |   ---                      ---                  ---
+          |---                            ---            ---
+          +----------------------------------============------------> Time
+          < Tr1><Tr2><   Ton    ><Tf1><Tf2 ><  Toff    >< Tr1><Tr2>
+
+Timing description:
+
+  * Tr1:    First rising time for 0% - 30% load.
+  * Tr2:    Second rising time for 31% - 100% load.
+  * Ton:    On time for 100% load.
+  * Tf1:    First falling time for 100% - 31% load.
+  * Tf2:    Second falling time for 30% to 0% load.
+  * Toff:   Off time for 0% load.
+
+  * Tr1/Tr2/Tf1/Tf2/Ton: 125ms to 3125ms, 200ms per step.
+  * Toff: 250ms to 6250ms, 400ms per step.
+
+Pattern example::
+
+       "0 125 0 125 0 125 0 125 0 625 0 1050"
+
+This Will configure Tr1/Tr2/Tf1/Tf2 to 125m, Ton to 625ms, and Toff to 1050ms.
diff --git a/Documentation/leds/ledtrig-oneshot.rst b/Documentation/leds/ledtrig-oneshot.rst
index 69fa3ea1d554..e044d69e9c0f 100644
--- a/Documentation/leds/ledtrig-oneshot.rst
+++ b/Documentation/leds/ledtrig-oneshot.rst
@@ -5,7 +5,7 @@ One-shot LED Trigger
 This is a LED trigger useful for signaling the user of an event where there are
 no clear trap points to put standard led-on and led-off settings.  Using this
 trigger, the application needs only to signal the trigger when an event has
-happened, than the trigger turns the LED on and than keeps it off for a
+happened, then the trigger turns the LED on and then keeps it off for a
 specified amount of time.
 
 This trigger is meant to be usable both for sporadic and dense events.  In the