Doc: use misc-devices/ dir for drivers

We have a directory for misc drivers documentation, let's use it.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

2 files changed, 121 insertions, 0 deletions

diff --git a/Documentation/misc-devices/c2port.txt b/Documentation/misc-devices/c2port.txt
new file mode 100644
index 000000000000..d9bf93ea4398
--- /dev/null
+++ b/Documentation/misc-devices/c2port.txt
@@ -0,0 +1,90 @@
+			C2 port support
+			---------------
+
+(C) Copyright 2007 Rodolfo Giometti <giometti@enneenne.com>
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+
+
+Overview
+--------
+
+This driver implements the support for Linux of Silicon Labs (Silabs)
+C2 Interface used for in-system programming of micro controllers.
+
+By using this driver you can reprogram the in-system flash without EC2
+or EC3 debug adapter. This solution is also useful in those systems
+where the micro controller is connected via special GPIOs pins.
+
+References
+----------
+
+The C2 Interface main references are at (http://www.silabs.com)
+Silicon Laboratories site], see:
+
+- AN127: FLASH Programming via the C2 Interface at
+http://www.silabs.com/public/documents/tpub_doc/anote/Microcontrollers/Small_Form_Factor/en/an127.pdf, and
+
+- C2 Specification at
+http://www.silabs.com/public/documents/tpub_doc/spec/Microcontrollers/en/C2spec.pdf,
+
+however it implements a two wire serial communication protocol (bit
+banging) designed to enable in-system programming, debugging, and
+boundary-scan testing on low pin-count Silicon Labs devices. Currently
+this code supports only flash programming but extensions are easy to
+add.
+
+Using the driver
+----------------
+
+Once the driver is loaded you can use sysfs support to get C2port's
+info or read/write in-system flash.
+
+# ls /sys/class/c2port/c2port0/
+access            flash_block_size  flash_erase       rev_id
+dev_id            flash_blocks_num  flash_size        subsystem/
+flash_access      flash_data        reset             uevent
+
+Initially the C2port access is disabled since you hardware may have
+such lines multiplexed with other devices so, to get access to the
+C2port, you need the command:
+
+# echo 1 > /sys/class/c2port/c2port0/access
+
+after that you should read the device ID and revision ID of the
+connected micro controller:
+
+# cat /sys/class/c2port/c2port0/dev_id
+8
+# cat /sys/class/c2port/c2port0/rev_id
+1
+
+However, for security reasons, the in-system flash access in not
+enabled yet, to do so you need the command:
+
+# echo 1 > /sys/class/c2port/c2port0/flash_access
+
+After that you can read the whole flash:
+
+# cat /sys/class/c2port/c2port0/flash_data > image
+
+erase it:
+
+# echo 1 > /sys/class/c2port/c2port0/flash_erase
+
+and write it:
+
+# cat image > /sys/class/c2port/c2port0/flash_data
+
+after writing you have to reset the device to execute the new code:
+
+# echo 1 > /sys/class/c2port/c2port0/reset
diff --git a/Documentation/misc-devices/ics932s401 b/Documentation/misc-devices/ics932s401
new file mode 100644
index 000000000000..07a739f406d8
--- /dev/null
+++ b/Documentation/misc-devices/ics932s401
@@ -0,0 +1,31 @@
+Kernel driver ics932s401
+======================
+
+Supported chips:
+  * IDT ICS932S401
+    Prefix: 'ics932s401'
+    Addresses scanned: I2C 0x69
+    Datasheet: Publically available at the IDT website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the IDT ICS932S401 chip family.
+
+This chip has 4 clock outputs--a base clock for the CPU (which is likely
+multiplied to get the real CPU clock), a system clock, a PCI clock, a USB
+clock, and a reference clock.  The driver reports selected and actual
+frequency.  If spread spectrum mode is enabled, the driver also reports by what
+percent the clock signal is being spread, which should be between 0 and -0.5%.
+All frequencies are reported in KHz.
+
+The ICS932S401 monitors all inputs continuously. The driver will not read
+the registers more often than once every other second.
+
+Special Features
+----------------
+
+The clocks could be reprogrammed to increase system speed.  I will not help you
+do this, as you risk damaging your system!