Merge tag 'thunderbolt-for-v6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus

Mika writes:

thunderbolt: Fixes for v6.7-rc3

This includes following USB4/Thunderbolt fixes for v6.7-rc3:

  - Fix a lane bonding issue on ASMedia USB4 device
  - Send uevents when link is switched to asymmetric or symmetric
  - Only add device router DP IN adapters to the head of resource list
    to avoid issues during system resume.

All these have been in linux-next with no reported issues.

* tag 'thunderbolt-for-v6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (1451 commits)
  thunderbolt: Only add device router DP IN to the head of the DP resource list
  thunderbolt: Send uevent after asymmetric/symmetric switch
  thunderbolt: Set lane bonding bit only for downstream port

1 files changed, 24 insertions, 25 deletions

diff --git a/Documentation/userspace-api/media/v4l/dev-subdev.rst b/Documentation/userspace-api/media/v4l/dev-subdev.rst
index a4f1df7093e8..43988516acdd 100644
--- a/Documentation/userspace-api/media/v4l/dev-subdev.rst
+++ b/Documentation/userspace-api/media/v4l/dev-subdev.rst
@@ -579,20 +579,19 @@ is started.
 
 There are three steps in configuring the streams:
 
-1) Set up links. Connect the pads between sub-devices using the :ref:`Media
-Controller API <media_controller>`
+1. Set up links. Connect the pads between sub-devices using the
+   :ref:`Media Controller API <media_controller>`
 
-2) Streams. Streams are declared and their routing is configured by
-setting the routing table for the sub-device using
-:ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl. Note that
-setting the routing table will reset formats and selections in the
-sub-device to default values.
+2. Streams. Streams are declared and their routing is configured by setting the
+   routing table for the sub-device using :ref:`VIDIOC_SUBDEV_S_ROUTING
+   <VIDIOC_SUBDEV_G_ROUTING>` ioctl. Note that setting the routing table will
+   reset formats and selections in the sub-device to default values.
 
-3) Configure formats and selections. Formats and selections of each stream
-are configured separately as documented for plain sub-devices in
-:ref:`format-propagation`. The stream ID is set to the same stream ID
-associated with either sink or source pads of routes configured using the
-:ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl.
+3. Configure formats and selections. Formats and selections of each stream are
+   configured separately as documented for plain sub-devices in
+   :ref:`format-propagation`. The stream ID is set to the same stream ID
+   associated with either sink or source pads of routes configured using the
+   :ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl.
 
 Multiplexed streams setup example
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
@@ -618,11 +617,11 @@ modeled as V4L2 devices, exposed to userspace via /dev/videoX nodes.
 
 To configure this pipeline, the userspace must take the following steps:
 
-1) Set up media links between entities: connect the sensors to the bridge,
-bridge to the receiver, and the receiver to the DMA engines. This step does
-not differ from normal non-multiplexed media controller setup.
+1. Set up media links between entities: connect the sensors to the bridge,
+   bridge to the receiver, and the receiver to the DMA engines. This step does
+   not differ from normal non-multiplexed media controller setup.
 
-2) Configure routing
+2. Configure routing
 
 .. flat-table:: Bridge routing table
     :header-rows:  1
@@ -656,14 +655,14 @@ not differ from normal non-multiplexed media controller setup.
       - V4L2_SUBDEV_ROUTE_FL_ACTIVE
       - Pixel data stream from Sensor B
 
-3) Configure formats and selections
+3. Configure formats and selections
 
-After configuring routing, the next step is configuring the formats and
-selections for the streams. This is similar to performing this step without
-streams, with just one exception: the ``stream`` field needs to be assigned
-to the value of the stream ID.
+   After configuring routing, the next step is configuring the formats and
+   selections for the streams. This is similar to performing this step without
+   streams, with just one exception: the ``stream`` field needs to be assigned
+   to the value of the stream ID.
 
-A common way to accomplish this is to start from the sensors and propagate the
-configurations along the stream towards the receiver,
-using :ref:`VIDIOC_SUBDEV_S_FMT <VIDIOC_SUBDEV_G_FMT>` ioctls to configure each
-stream endpoint in each sub-device.
+   A common way to accomplish this is to start from the sensors and propagate
+   the configurations along the stream towards the receiver, using
+   :ref:`VIDIOC_SUBDEV_S_FMT <VIDIOC_SUBDEV_G_FMT>` ioctls to configure each
+   stream endpoint in each sub-device.