Automatic merge with /usr/src/ntfs-2.6.git

2 files changed, 252 insertions, 32 deletions

diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl
index cf2fce7707da..6df1dfd18b65 100644
--- a/Documentation/DocBook/libata.tmpl
+++ b/Documentation/DocBook/libata.tmpl
@@ -14,7 +14,7 @@
   </authorgroup>
 
   <copyright>
-   <year>2003</year>
+   <year>2003-2005</year>
    <holder>Jeff Garzik</holder>
   </copyright>
 
@@ -44,30 +44,38 @@
 
 <toc></toc>
 
-  <chapter id="libataThanks">
-     <title>Thanks</title>
+  <chapter id="libataIntroduction">
+     <title>Introduction</title>
   <para>
-  The bulk of the ATA knowledge comes thanks to long conversations with
-  Andre Hedrick (www.linux-ide.org).
+  libATA is a library used inside the Linux kernel to support ATA host
+  controllers and devices.  libATA provides an ATA driver API, class
+  transports for ATA and ATAPI devices, and SCSI&lt;-&gt;ATA translation
+  for ATA devices according to the T10 SAT specification.
   </para>
   <para>
-  Thanks to Alan Cox for pointing out similarities 
-  between SATA and SCSI, and in general for motivation to hack on
-  libata.
-  </para>
-  <para>
-  libata's device detection
-  method, ata_pio_devchk, and in general all the early probing was
-  based on extensive study of Hale Landis's probe/reset code in his
-  ATADRVR driver (www.ata-atapi.com).
+  This Guide documents the libATA driver API, library functions, library
+  internals, and a couple sample ATA low-level drivers.
   </para>
   </chapter>
 
   <chapter id="libataDriverApi">
      <title>libata Driver API</title>
+     <para>
+     struct ata_port_operations is defined for every low-level libata
+     hardware driver, and it controls how the low-level driver
+     interfaces with the ATA and SCSI layers.
+     </para>
+     <para>
+     FIS-based drivers will hook into the system with ->qc_prep() and
+     ->qc_issue() high-level hooks.  Hardware which behaves in a manner
+     similar to PCI IDE hardware may utilize several generic helpers,
+     defining at a bare minimum the bus I/O addresses of the ATA shadow
+     register blocks.
+     </para>
      <sect1>
         <title>struct ata_port_operations</title>
 
+	<sect2><title>Disable ATA port</title>
 	<programlisting>
 void (*port_disable) (struct ata_port *);
 	</programlisting>
@@ -78,6 +86,9 @@ void (*port_disable) (struct ata_port *);
 	unplug).
 	</para>
 
+	</sect2>
+
+	<sect2><title>Post-IDENTIFY device configuration</title>
 	<programlisting>
 void (*dev_config) (struct ata_port *, struct ata_device *);
 	</programlisting>
@@ -88,6 +99,9 @@ void (*dev_config) (struct ata_port *, struct ata_device *);
 	issue of SET FEATURES - XFER MODE, and prior to operation.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Set PIO/DMA mode</title>
 	<programlisting>
 void (*set_piomode) (struct ata_port *, struct ata_device *);
 void (*set_dmamode) (struct ata_port *, struct ata_device *);
@@ -108,6 +122,9 @@ void (*post_set_mode) (struct ata_port *ap);
 	->set_dma_mode() is only called if DMA is possible.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Taskfile read/write</title>
 	<programlisting>
 void (*tf_load) (struct ata_port *ap, struct ata_taskfile *tf);
 void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
@@ -120,6 +137,9 @@ void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
 	taskfile register values.
 	</para>
 
+	</sect2>
+
+	<sect2><title>ATA command execute</title>
 	<programlisting>
 void (*exec_command)(struct ata_port *ap, struct ata_taskfile *tf);
 	</programlisting>
@@ -129,17 +149,37 @@ void (*exec_command)(struct ata_port *ap, struct ata_taskfile *tf);
 	->tf_load(), to be initiated in hardware.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Per-cmd ATAPI DMA capabilities filter</title>
+	<programlisting>
+int (*check_atapi_dma) (struct ata_queued_cmd *qc);
+	</programlisting>
+
+	<para>
+Allow low-level driver to filter ATA PACKET commands, returning a status
+indicating whether or not it is OK to use DMA for the supplied PACKET
+command.
+	</para>
+
+	</sect2>
+
+	<sect2><title>Read specific ATA shadow registers</title>
 	<programlisting>
 u8   (*check_status)(struct ata_port *ap);
-void (*dev_select)(struct ata_port *ap, unsigned int device);
+u8   (*check_altstatus)(struct ata_port *ap);
+u8   (*check_err)(struct ata_port *ap);
 	</programlisting>
 
 	<para>
-	Reads the Status ATA shadow register from hardware.  On some
-	hardware, this has the side effect of clearing the interrupt
-	condition.
+	Reads the Status/AltStatus/Error ATA shadow register from
+	hardware.  On some hardware, reading the Status register has
+	the side effect of clearing the interrupt condition.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Select ATA device on bus</title>
 	<programlisting>
 void (*dev_select)(struct ata_port *ap, unsigned int device);
 	</programlisting>
@@ -147,9 +187,13 @@ void (*dev_select)(struct ata_port *ap, unsigned int device);
 	<para>
 	Issues the low-level hardware command(s) that causes one of N
 	hardware devices to be considered 'selected' (active and
-	available for use) on the ATA bus.
+	available for use) on the ATA bus.  This generally has no
+meaning on FIS-based devices.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Reset ATA bus</title>
 	<programlisting>
 void (*phy_reset) (struct ata_port *ap);
 	</programlisting>
@@ -162,17 +206,31 @@ void (*phy_reset) (struct ata_port *ap);
 	functions ata_bus_reset() or sata_phy_reset() for this hook.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Control PCI IDE BMDMA engine</title>
 	<programlisting>
 void (*bmdma_setup) (struct ata_queued_cmd *qc);
 void (*bmdma_start) (struct ata_queued_cmd *qc);
+void (*bmdma_stop) (struct ata_port *ap);
+u8   (*bmdma_status) (struct ata_port *ap);
 	</programlisting>
 
 	<para>
-	When setting up an IDE BMDMA transaction, these hooks arm
-	(->bmdma_setup) and fire (->bmdma_start) the hardware's DMA
-	engine.
+When setting up an IDE BMDMA transaction, these hooks arm
+(->bmdma_setup), fire (->bmdma_start), and halt (->bmdma_stop)
+the hardware's DMA engine.  ->bmdma_status is used to read the standard
+PCI IDE DMA Status register.
 	</para>
 
+	<para>
+These hooks are typically either no-ops, or simply not implemented, in
+FIS-based drivers.
+	</para>
+
+	</sect2>
+
+	<sect2><title>High-level taskfile hooks</title>
 	<programlisting>
 void (*qc_prep) (struct ata_queued_cmd *qc);
 int (*qc_issue) (struct ata_queued_cmd *qc);
@@ -190,20 +248,26 @@ int (*qc_issue) (struct ata_queued_cmd *qc);
 	->qc_issue is used to make a command active, once the hardware
 	and S/G tables have been prepared.  IDE BMDMA drivers use the
 	helper function ata_qc_issue_prot() for taskfile protocol-based
-	dispatch.  More advanced drivers roll their own ->qc_issue
-	implementation, using this as the "issue new ATA command to
-	hardware" hook.
+	dispatch.  More advanced drivers implement their own ->qc_issue.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Timeout (error) handling</title>
 	<programlisting>
 void (*eng_timeout) (struct ata_port *ap);
 	</programlisting>
 
 	<para>
-	This is a high level error handling function, called from the
-	error handling thread, when a command times out.
+This is a high level error handling function, called from the
+error handling thread, when a command times out.  Most newer
+hardware will implement its own error handling code here.  IDE BMDMA
+drivers may use the helper function ata_eng_timeout().
 	</para>
 
+	</sect2>
+
+	<sect2><title>Hardware interrupt handling</title>
 	<programlisting>
 irqreturn_t (*irq_handler)(int, void *, struct pt_regs *);
 void (*irq_clear) (struct ata_port *);
@@ -216,6 +280,9 @@ void (*irq_clear) (struct ata_port *);
 	is quiet.
 	</para>
 
+	</sect2>
+
+	<sect2><title>SATA phy read/write</title>
 	<programlisting>
 u32 (*scr_read) (struct ata_port *ap, unsigned int sc_reg);
 void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
@@ -227,6 +294,9 @@ void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
 	if ->phy_reset hook called the sata_phy_reset() helper function.
 	</para>
 
+	</sect2>
+
+	<sect2><title>Init and shutdown</title>
 	<programlisting>
 int (*port_start) (struct ata_port *ap);
 void (*port_stop) (struct ata_port *ap);
@@ -240,15 +310,17 @@ void (*host_stop) (struct ata_host_set *host_set);
 	tasks.  
 	</para>
 	<para>
-	->host_stop() is called when the rmmod or hot unplug process
-	begins.  The hook must stop all hardware interrupts, DMA
-	engines, etc.
-	</para>
-	<para>
 	->port_stop() is called after ->host_stop().  It's sole function
 	is to release DMA/memory resources, now that they are no longer
 	actively being used.
 	</para>
+	<para>
+	->host_stop() is called after all ->port_stop() calls
+have completed.  The hook must finalize hardware shutdown, release DMA
+and other resources, etc.
+	</para>
+
+	</sect2>
 
      </sect1>
   </chapter>
@@ -279,4 +351,24 @@ void (*host_stop) (struct ata_host_set *host_set);
 !Idrivers/scsi/sata_sil.c
   </chapter>
 
+  <chapter id="libataThanks">
+     <title>Thanks</title>
+  <para>
+  The bulk of the ATA knowledge comes thanks to long conversations with
+  Andre Hedrick (www.linux-ide.org), and long hours pondering the ATA
+  and SCSI specifications.
+  </para>
+  <para>
+  Thanks to Alan Cox for pointing out similarities 
+  between SATA and SCSI, and in general for motivation to hack on
+  libata.
+  </para>
+  <para>
+  libata's device detection
+  method, ata_pio_devchk, and in general all the early probing was
+  based on extensive study of Hale Landis's probe/reset code in his
+  ATADRVR driver (www.ata-atapi.com).
+  </para>
+  </chapter>
+
 </book>
diff --git a/Documentation/cpu-freq/cpufreq-stats.txt b/Documentation/cpu-freq/cpufreq-stats.txt
new file mode 100644
index 000000000000..e2d1e760b4ba
--- /dev/null
+++ b/Documentation/cpu-freq/cpufreq-stats.txt
@@ -0,0 +1,128 @@
+
+     CPU frequency and voltage scaling statictics in the Linux(TM) kernel
+
+
+             L i n u x    c p u f r e q - s t a t s   d r i v e r
+
+                       - information for users -
+
+
+             Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
+
+Contents
+1. Introduction
+2. Statistics Provided (with example)
+3. Configuring cpufreq-stats
+
+
+1. Introduction
+
+cpufreq-stats is a driver that provices CPU frequency statistics for each CPU.
+This statistics is provided in /sysfs as a bunch of read_only interfaces. This
+interface (when configured) will appear in a seperate directory under cpufreq
+in /sysfs (<sysfs root>/devices/system/cpu/cpuX/cpufreq/stats/) for each CPU.
+Various statistics will form read_only files under this directory.
+
+This driver is designed to be independent of any particular cpufreq_driver
+that may be running on your CPU. So, it will work with any cpufreq_driver.
+
+
+2. Statistics Provided (with example)
+
+cpufreq stats provides following statistics (explained in detail below).
+-  time_in_state
+-  total_trans
+-  trans_table
+
+All the statistics will be from the time the stats driver has been inserted 
+to the time when a read of a particular statistic is done. Obviously, stats 
+driver will not have any information about the the frequcny transitions before
+the stats driver insertion.
+
+--------------------------------------------------------------------------------
+<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # ls -l
+total 0
+drwxr-xr-x  2 root root    0 May 14 16:06 .
+drwxr-xr-x  3 root root    0 May 14 15:58 ..
+-r--r--r--  1 root root 4096 May 14 16:06 time_in_state
+-r--r--r--  1 root root 4096 May 14 16:06 total_trans
+-r--r--r--  1 root root 4096 May 14 16:06 trans_table
+--------------------------------------------------------------------------------
+
+-  time_in_state
+This gives the amount of time spent in each of the frequencies supported by
+this CPU. The cat output will have "<frequency> <time>" pair in each line, which
+will mean this CPU spent <time> usertime units of time at <frequency>. Output
+will have one line for each of the supported freuencies. usertime units here 
+is 10mS (similar to other time exported in /proc).
+
+--------------------------------------------------------------------------------
+<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat time_in_state 
+3600000 2089
+3400000 136
+3200000 34
+3000000 67
+2800000 172488
+--------------------------------------------------------------------------------
+
+
+-  total_trans
+This gives the total number of frequency transitions on this CPU. The cat 
+output will have a single count which is the total number of frequency
+transitions.
+
+--------------------------------------------------------------------------------
+<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat total_trans
+20
+--------------------------------------------------------------------------------
+
+-  trans_table
+This will give a fine grained information about all the CPU frequency
+transitions. The cat output here is a two dimensional matrix, where an entry
+<i,j> (row i, column j) represents the count of number of transitions from 
+Freq_i to Freq_j. Freq_i is in descending order with increasing rows and 
+Freq_j is in descending order with increasing columns. The output here also 
+contains the actual freq values for each row and column for better readability.
+
+--------------------------------------------------------------------------------
+<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat trans_table
+   From  :    To
+         :   3600000   3400000   3200000   3000000   2800000 
+  3600000:         0         5         0         0         0 
+  3400000:         4         0         2         0         0 
+  3200000:         0         1         0         2         0 
+  3000000:         0         0         1         0         3 
+  2800000:         0         0         0         2         0 
+--------------------------------------------------------------------------------
+
+
+3. Configuring cpufreq-stats
+
+To configure cpufreq-stats in your kernel
+Config Main Menu
+	Power management options (ACPI, APM)  --->
+		CPU Frequency scaling  --->
+			[*] CPU Frequency scaling
+			<*>   CPU frequency translation statistics 
+			[*]     CPU frequency translation statistics details
+
+
+"CPU Frequency scaling" (CONFIG_CPU_FREQ) should be enabled to configure
+cpufreq-stats.
+
+"CPU frequency translation statistics" (CONFIG_CPU_FREQ_STAT) provides the
+basic statistics which includes time_in_state and total_trans.
+
+"CPU frequency translation statistics details" (CONFIG_CPU_FREQ_STAT_DETAILS)
+provides fine grained cpufreq stats by trans_table. The reason for having a
+seperate config option for trans_table is:
+- trans_table goes against the traditional /sysfs rule of one value per
+  interface. It provides a whole bunch of value in a 2 dimensional matrix
+  form.
+
+Once these two options are enabled and your CPU supports cpufrequency, you
+will be able to see the CPU frequency statistics in /sysfs.
+
+
+
+