Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.2 merge window

- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs

Signed-off-by: Felipe Balbi <balbi@ti.com>

7 files changed, 33 insertions, 11 deletions

diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt
index d5c706216df5..3b4ea1b73b38 100644
--- a/Documentation/devicetree/bindings/power/twl-charger.txt
+++ b/Documentation/devicetree/bindings/power/twl-charger.txt
@@ -1,5 +1,15 @@
 TWL BCI (Battery Charger Interface)
 
+The battery charger needs to interact with the USB phy in order
+to know when charging is permissible, and when there is a connection
+or disconnection.
+
+The choice of phy cannot be configured at a hardware level, so there
+is no value in explicit configuration in device-tree.  Rather
+if there is a sibling of the BCI node which is compatible with
+"ti,twl4030-usb", then that is used to determine when and how
+use USB power for charging.
+
 Required properties:
 - compatible:
   - "ti,twl4030-bci"
diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt
index f9d70252bbb2..01c71b1258f4 100644
--- a/Documentation/devicetree/bindings/usb/dwc3-st.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
@@ -49,8 +49,7 @@ st_dwc3: dwc3@8f94000 {
 	st,syscfg	= <&syscfg_core>;
 	resets		= <&powerdown STIH407_USB3_POWERDOWN>,
 			  <&softreset STIH407_MIPHY2_SOFTRESET>;
-	reset-names	= "powerdown",
-			  "softreset";
+	reset-names	= "powerdown", "softreset";
 	#address-cells	= <1>;
 	#size-cells	= <1>;
 	pinctrl-names	= "default";
@@ -62,7 +61,7 @@ st_dwc3: dwc3@8f94000 {
 		reg		= <0x09900000 0x100000>;
 		interrupts	= <GIC_SPI 155 IRQ_TYPE_NONE>;
 		dr_mode		= "host";
-		phys-names      = "usb2-phy", "usb3-phy";
-		phys            = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>;
+		phy-names	= "usb2-phy", "usb3-phy";
+		phys		= <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>;
 	};
 };
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 5cc364309edb..0815eac5b185 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -38,6 +38,8 @@ Optional properties:
  - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
 			utmi_l1_suspend_n, false when asserts utmi_sleep_n
  - snps,hird-threshold: HIRD threshold
+ - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
+   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
 
 This is usually a subnode to DWC3 glue to which it is connected.
 
diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
index 2826f2af503a..bd8d9e753029 100644
--- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt
+++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
@@ -69,6 +69,17 @@ Optional properties:
                 (no, min, max) where each value represents either a voltage
                 in microvolts or a value corresponding to voltage corner.
 
+- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
+                and controller driver therefore enables pull-up explicitly
+                before starting controller using usbcmd run/stop bit.
+
+- extcon:       phandles to external connector devices. First phandle
+                should point to external connector, which provide "USB"
+                cable events, the second should point to external connector
+                device, which provide "USB-HOST" cable events. If one of
+                the external connector devices is not required empty <0>
+                phandle should be specified.
+
 Example HSUSB OTG controller device node:
 
     usb@f9a55000 {
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index dc2a18f0b3a1..64a4ca6cf96f 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -4,6 +4,7 @@ Required properties:
   - compatible: Must contain one of the following:
 	- "renesas,usbhs-r8a7790"
 	- "renesas,usbhs-r8a7791"
+	- "renesas,usbhs-r8a7794"
   - reg: Base address and length of the register for the USBHS
   - interrupts: Interrupt specifier for the USBHS
   - clocks: A list of phandle + clock specifier pairs
@@ -15,10 +16,8 @@ Optional properties:
   - phys: phandle + phy specifier pair
   - phy-names: must be "usb"
   - dmas: Must contain a list of references to DMA specifiers.
-  - dma-names : Must contain a list of DMA names:
-   - tx0 ... tx<n>
-   - rx0 ... rx<n>
-    - This <n> means DnFIFO in USBHS module.
+  - dma-names : named "ch%d", where %d is the channel number ranging from zero
+                to the number of channels (DnFIFOs) minus one.
 
 Example:
 	usbhs: usb@e6590000 {
diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
index 0aee0ad3f035..17327a296110 100644
--- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -30,6 +30,9 @@ TWL4030 USB PHY AND COMPARATOR
  - usb_mode : The mode used by the phy to connect to the controller. "1"
    specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
 
+If a sibling node is compatible "ti,twl4030-bci", then it will find
+this device and query it for USB power status.
+
 twl4030-usb {
 	compatible = "ti,twl4030-usb";
 	interrupts = < 10 4 >;
diff --git a/Documentation/usb/gadget-testing.txt b/Documentation/usb/gadget-testing.txt
index f45b2bf4b41d..592678009c15 100644
--- a/Documentation/usb/gadget-testing.txt
+++ b/Documentation/usb/gadget-testing.txt
@@ -526,8 +526,6 @@ Except for ifname they can be written to until the function is linked to a
 configuration. The ifname is read-only and contains the name of the interface
 which was assigned by the net core, e. g. usb0.
 
-By default there can be only 1 RNDIS interface in the system.
-
 Testing the RNDIS function
 --------------------------
 
@@ -629,7 +627,7 @@ Function-specific configfs interface
 The function name to use when creating the function directory is "uac2".
 The uac2 function provides these attributes in its function directory:
 
-	chmask - capture channel mask
+	c_chmask - capture channel mask
 	c_srate - capture sampling rate
 	c_ssize - capture sample size (bytes)
 	p_chmask - playback channel mask