Merge tag 'musb-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

usb: musb: patches for v3.7 merge window

Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.

We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.

Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.

All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.

2 files changed, 47 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
new file mode 100644
index 000000000000..ca8fa56e9f03
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -0,0 +1,14 @@
+AM33XX MUSB GLUE
+ - compatible : Should be "ti,musb-am33xx"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
+   represents PERIPHERAL.
+ - power : Should be "250". This signifies the controller can supply upto
+   500mA when operating in host mode.
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
new file mode 100644
index 000000000000..29a043ecda52
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -0,0 +1,33 @@
+OMAP GLUE
+
+OMAP MUSB GLUE
+ - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - interface_type : This is a board specific setting to describe the type of
+   interface between the controller and the phy. It should be "0" or "1"
+   specifying ULPI and UTMI respectively.
+ - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - power : Should be "50". This signifies the controller can supply upto
+   100mA when operating in host mode.
+
+SOC specific device node entry
+usb_otg_hs: usb_otg_hs@4a0ab000 {
+	compatible = "ti,omap4-musb";
+	ti,hwmods = "usb_otg_hs";
+	multipoint = <1>;
+	num_eps = <16>;
+	ram_bits = <12>;
+};
+
+Board specific device node entry
+&usb_otg_hs {
+	interface_type = <1>;
+	mode = <3>;
+	power = <50>;
+};