Merge tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO updates from Greg KH:
 "Here's the "big" staging/iio pull request for 4.10-rc1.

  Not as big as 4.9 was, but still just over a thousand changes. We
  almost broke even of lines added vs. removed, as the slicoss driver
  was removed (got a "clean" driver for the same hardware through the
  netdev tree), and some iio drivers were also dropped, but I think we
  ended up adding a few thousand lines to the source tree in the end.
  Other than that it's a lot of minor fixes all over the place, nothing
  major stands out at all.

  All of these have been in linux-next for a while. There will be a
  merge conflict with Al's vfs tree in the lustre code, but the
  resolution for that should be pretty simple, that too has been in
  linux-next"

* tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits)
  staging: comedi: comedidev.h: Document usage of 'detach' handler
  staging: fsl-mc: remove unnecessary info prints from bus driver
  staging: fsl-mc: add sysfs ABI doc
  staging/lustre/o2iblnd: Fix misspelled attemps->attempts
  staging/lustre/o2iblnd: Fix misspelling intialized->intialized
  staging/lustre: Convert all bare unsigned to unsigned int
  staging/lustre/socklnd: Fix whitespace problem
  staging/lustre/o2iblnd: Add missing space
  staging/lustre/lnetselftest: Fix potential integer overflow
  staging: greybus: audio_module: remove redundant OOM message
  staging: dgnc: Fix lines longer than 80 characters
  staging: dgnc: fix blank line after '{' warnings.
  staging/android: remove Sync Framework tasks from TODO
  staging/lustre/osc: Revert erroneous list_for_each_entry_safe use
  staging: slicoss: remove the staging driver
  staging: lustre: libcfs: remove lnet upcall code
  staging: lustre: remove set but unused variables
  staging: lustre: osc: set lock data for readahead lock
  staging: lustre: import: don't reconnect during connect interpret
  staging: lustre: clio: remove mtime check in vvp_io_fault_start()
  ...

22 files changed, 652 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-fsl-mc b/Documentation/ABI/testing/sysfs-bus-fsl-mc
new file mode 100644
index 000000000000..80256b8b4f26
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-fsl-mc
@@ -0,0 +1,21 @@
+What:		/sys/bus/fsl-mc/drivers/.../bind
+Date:		December 2016
+Contact:	stuart.yoder@nxp.com
+Description:
+		Writing a device location to this file will cause
+		the driver to attempt to bind to the device found at
+		this location. The format for the location is Object.Id
+		and is the same as found in /sys/bus/fsl-mc/devices/.
+                For example:
+		# echo dpni.2 > /sys/bus/fsl-mc/drivers/fsl_dpaa2_eth/bind
+
+What:		/sys/bus/fsl-mc/drivers/.../unbind
+Date:		December 2016
+Contact:	stuart.yoder@nxp.com
+Description:
+		Writing a device location to this file will cause the
+		driver to attempt to unbind from the device found at
+		this location. The format for the location is Object.Id
+		and is the same as found in /sys/bus/fsl-mc/devices/.
+                For example:
+		# echo dpni.2 > /sys/bus/fsl-mc/drivers/fsl_dpaa2_eth/unbind
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index fee35c00cc4e..b8f220f978dd 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -329,6 +329,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_pressure_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_humidityrelative_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_illuminance_scale
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_scale
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -1579,3 +1580,20 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		Raw (unscaled no offset etc.) electric conductivity reading that
 		can be processed to siemens per meter.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_raw
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw counter device counts from channel Y. For quadrature
+		counters, multiplication by an available [Y]_scale results in
+		the counts of a single quadrature signal phase from channel Y.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_indexY_raw
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw counter device index value from channel Y. This attribute
+		provides an absolute positional reference (e.g. a pulse once per
+		revolution) which may be used to home positional systems as
+		required.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector b/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector
new file mode 100644
index 000000000000..2071f9bcfaa5
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector
@@ -0,0 +1,36 @@
+What:		/sys/bus/iio/devices/iio:deviceX/in_altvoltageY_invert
+Date:		October 2016
+KernelVersion:	4.9
+Contact:	Peter Rosin <peda@axentia.se>
+Description:
+		The DAC is used to find the peak level of an alternating
+		voltage input signal by a binary search using the output
+		of a comparator wired to an interrupt pin. Like so:
+		                           _
+		                          | \
+		     input +------>-------|+ \
+		                          |   \
+		            .-------.     |    }---.
+		            |       |     |   /    |
+		            |    dac|-->--|- /     |
+		            |       |     |_/      |
+		            |       |              |
+		            |       |              |
+		            |    irq|------<-------'
+		            |       |
+		            '-------'
+		The boolean invert attribute (0/1) should be set when the
+		input signal is centered around the maximum value of the
+		dac instead of zero. The envelope detector will search
+		from below in this case and will also invert the result.
+		The edge/level of the interrupt is also switched to its
+		opposite value.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_altvoltageY_compare_interval
+Date:		October 2016
+KernelVersion:	4.9
+Contact:	Peter Rosin <peda@axentia.se>
+Description:
+		Number of milliseconds to wait for the comparator in each
+		step of the binary search for the input peak level. Needs
+		to relate to the frequency of the input signal.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8 b/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8
new file mode 100644
index 000000000000..ba676520b953
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8
@@ -0,0 +1,125 @@
+What:		/sys/bus/iio/devices/iio:deviceX/in_count_count_direction_available
+What:		/sys/bus/iio/devices/iio:deviceX/in_count_count_mode_available
+What:		/sys/bus/iio/devices/iio:deviceX/in_count_noise_error_available
+What:		/sys/bus/iio/devices/iio:deviceX/in_count_quadrature_mode_available
+What:		/sys/bus/iio/devices/iio:deviceX/in_index_index_polarity_available
+What:		/sys/bus/iio/devices/iio:deviceX/in_index_synchronous_mode_available
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Discrete set of available values for the respective counter
+		configuration are listed in this file.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_count_direction
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Read-only attribute that indicates whether the counter for
+		channel Y is counting up or down.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_count_mode
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Count mode for channel Y. Four count modes are available:
+		normal, range limit, non-recycle, and modulo-n. The preset value
+		for channel Y is used by the count mode where required.
+
+		Normal:
+			Counting is continuous in either direction.
+
+		Range Limit:
+			An upper or lower limit is set, mimicking limit switches
+			in the mechanical counterpart. The upper limit is set to
+			the preset value, while the lower limit is set to 0. The
+			counter freezes at count = preset when counting up, and
+			at count = 0 when counting down. At either of these
+			limits, the counting is resumed only when the count
+			direction is reversed.
+
+		Non-recycle:
+			Counter is disabled whenever a 24-bit count overflow or
+			underflow takes place. The counter is re-enabled when a
+			new count value is loaded to the counter via a preset
+			operation or write to raw.
+
+		Modulo-N:
+			A count boundary is set between 0 and the preset value.
+			The counter is reset to 0 at count = preset when
+			counting up, while the counter is set to the preset
+			value at count = 0 when counting down; the counter does
+			not freeze at the bundary points, but counts
+			continuously throughout.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_noise_error
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Read-only attribute that indicates whether excessive noise is
+		present at the channel Y count inputs in quadrature clock mode;
+		irrelevant in non-quadrature clock mode.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_preset
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		If the counter device supports preset registers, the preset
+		count for channel Y is provided by this attribute.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_quadrature_mode
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Configure channel Y counter for non-quadrature or quadrature
+		clock mode. Selecting non-quadrature clock mode will disable
+		synchronous load mode. In quadrature clock mode, the channel Y
+		scale attribute selects the encoder phase division (scale of 1
+		selects full-cycle, scale of 0.5 selects half-cycle, scale of
+		0.25 selects quarter-cycle) processed by the channel Y counter.
+
+		Non-quadrature:
+			The filter and decoder circuit are bypassed. Encoder A
+			input serves as the count input and B as the UP/DOWN
+			direction control input, with B = 1 selecting UP Count
+			mode and B = 0 selecting Down Count mode.
+
+		Quadrature:
+			Encoder A and B inputs are digitally filtered and
+			decoded for UP/DN clock.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_countY_set_to_preset_on_index
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Whether to set channel Y counter with channel Y preset value
+		when channel Y index input is active, or continuously count.
+		Valid attribute values are boolean.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_indexY_index_polarity
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Active level of channel Y index input; irrelevant in
+		non-synchronous load mode.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_indexY_synchronous_mode
+KernelVersion:	4.9
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Configure channel Y counter for non-synchronous or synchronous
+		load mode. Synchronous load mode cannot be selected in
+		non-quadrature clock mode.
+
+		Non-synchronous:
+			A logic low level is the active level at this index
+			input. The index function (as enabled via
+			set_to_preset_on_index) is performed directly on the
+			active level of the index input.
+
+		Synchronous:
+			Intended for interfacing with encoder Index output in
+			quadrature clock mode. The active level is configured
+			via index_polarity. The index function (as enabled via
+			set_to_preset_on_index) is performed synchronously with
+			the quadrature clock on the active level of the index
+			input.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-cros-ec b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec
new file mode 100644
index 000000000000..297b9720f024
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec
@@ -0,0 +1,18 @@
+What:		/sys/bus/iio/devices/iio:deviceX/calibrate
+Date:		July 2015
+KernelVersion:	4.7
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Writing '1' will perform a FOC (Fast Online Calibration). The
+                corresponding calibration offsets can be read from *_calibbias
+                entries.
+
+What:		/sys/bus/iio/devices/iio:deviceX/location
+Date:		July 2015
+KernelVersion:	4.7
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This attribute returns a string with the physical location where
+                the motion sensor is placed. For example, in a laptop a motion
+                sensor can be located on the base or on the lid. Current valid
+		values are 'base' and 'lid'.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac b/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac
new file mode 100644
index 000000000000..580e93f373f6
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac
@@ -0,0 +1,8 @@
+What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_raw_available
+Date:		October 2016
+KernelVersion:	4.9
+Contact:	Peter Rosin <peda@axentia.se>
+Description:
+		The range of available values represented as the minimum value,
+		the step and the maximum value, all enclosed in square brackets.
+		Example: [0 1 256]
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018 b/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018
new file mode 100644
index 000000000000..f0ce0a0476ea
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018
@@ -0,0 +1,19 @@
+What:		/sys/bus/iio/devices/iio:deviceX/proximity_on_chip_ambient_infrared_suppression
+Date:		January 2011
+KernelVersion:	2.6.37
+Contact:	linux-iio@vger.kernel.org
+Description:
+		From ISL29018 Data Sheet (FN6619.4, Oct 8, 2012) regarding the
+		infrared suppression:
+
+		Scheme 0, makes full n (4, 8, 12, 16) bits (unsigned) proximity
+		detection. The range of Scheme 0 proximity count is from 0 to
+		2^n. Logic 1 of this bit, Scheme 1, makes n-1 (3, 7, 11, 15)
+		bits (2's complementary) proximity_less_ambient detection. The
+		range of Scheme 1 proximity count is from -2^(n-1) to 2^(n-1).
+		The sign bit is extended for resolutions less than 16. While
+		Scheme 0 has wider dynamic range, Scheme 1 proximity detection
+		is less affected by the ambient IR noise variation.
+
+		0 Sensing IR from LED and ambient
+		1 Sensing IR from LED with ambient IR rejection
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583 b/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583
new file mode 100644
index 000000000000..a2e19964e87e
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583
@@ -0,0 +1,20 @@
+What:		/sys/bus/iio/devices/device[n]/in_illuminance_calibrate
+KernelVersion:	2.6.37
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This property causes an internal calibration of the als gain trim
+		value which is later used in calculating illuminance in lux.
+
+What:		/sys/bus/iio/devices/device[n]/in_illuminance_lux_table
+KernelVersion:	2.6.37
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This property gets/sets the table of coefficients
+		used in calculating illuminance in lux.
+
+What:		/sys/bus/iio/devices/device[n]/in_illuminance_input_target
+KernelVersion:	2.6.37
+Contact:	linux-iio@vger.kernel.org
+Description:
+		This property is the known externally illuminance (in lux).
+		It is used in the process of calibrating the device accuracy.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531 b/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531
new file mode 100644
index 000000000000..2a91fbe394fc
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531
@@ -0,0 +1,8 @@
+What:		/sys/bus/iio/devices/iio:deviceX/out_resistance_raw_available
+Date:		October 2016
+KernelVersion:	4.9
+Contact:	Peter Rosin <peda@axentia.se>
+Description:
+		The range of available values represented as the minimum value,
+		the step and the maximum value, all enclosed in square brackets.
+		Example: [0 1 256]
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index fbbad6446741..03349ad5abfa 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -39,11 +39,13 @@ dallas,ds75		Digital Thermometer and Thermostat
 dlg,da9053		DA9053: flexible system level PMIC with multicore support
 dlg,da9063		DA9063: system PMIC for quad-core application processors
 domintech,dmard09	DMARD09: 3-axis Accelerometer
+domintech,dmard10	DMARD10: 3-axis Accelerometer
 epson,rx8010		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
 epson,rx8025		High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE
 epson,rx8581		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
 fsl,mag3110		MAG3110: Xtrinsic High Accuracy, 3D Magnetometer
 fsl,mc13892		MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51
+fsl,mma7660		MMA7660FC: 3-Axis Orientation/Motion Detection Sensor
 fsl,mma8450		MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer
 fsl,mpl3115		MPL3115: Absolute Digital Pressure Sensor
 fsl,mpr121		MPR121: Proximity Capacitive Touch Sensor Controller
@@ -57,6 +59,7 @@ maxim,max1237		Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
 maxim,max6625		9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface
 mc,rv3029c2		Real Time Clock Module with I2C-Bus
 mcube,mc3230		mCube 3-axis 8-bit digital accelerometer
+memsic,mxc6225		MEMSIC 2-axis 8-bit digital accelerometer
 microchip,mcp4531-502	Microchip 7-bit Single I2C Digital Potentiometer (5k)
 microchip,mcp4531-103	Microchip 7-bit Single I2C Digital Potentiometer (10k)
 microchip,mcp4531-503	Microchip 7-bit Single I2C Digital Potentiometer (50k)
@@ -121,6 +124,9 @@ microchip,mcp4662-502	Microchip 8-bit Dual I2C Digital Potentiometer with NV Mem
 microchip,mcp4662-103	Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k)
 microchip,mcp4662-503	Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k)
 microchip,mcp4662-104	Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k)
+miramems,da226		MiraMEMS DA226 2-axis 14-bit digital accelerometer
+miramems,da280		MiraMEMS DA280 3-axis 14-bit digital accelerometer
+miramems,da311		MiraMEMS DA311 3-axis 12-bit digital accelerometer
 national,lm63		Temperature sensor with integrated fan control
 national,lm75		I2C TEMP SENSOR
 national,lm80		Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
@@ -146,6 +152,7 @@ ricoh,rv5c387a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
 sgx,vz89x		SGX Sensortech VZ89X Sensors
 sii,s35390a		2-wire CMOS real-time clock
+silabs,si7020		Relative Humidity and Temperature Sensors
 skyworks,sky81452	Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply
 st,24c256		i2c serial eeprom  (24cxx)
 st,m41t00		Serial real-time clock (RTC)
diff --git a/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt
new file mode 100644
index 000000000000..27544bdd4478
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt
@@ -0,0 +1,54 @@
+Bindings for ADC envelope detector using a DAC and a comparator
+
+The DAC is used to find the peak level of an alternating voltage input
+signal by a binary search using the output of a comparator wired to
+an interrupt pin. Like so:
+                          _
+                         | \
+    input +------>-------|+ \
+                         |   \
+           .-------.     |    }---.
+           |       |     |   /    |
+           |    dac|-->--|- /     |
+           |       |     |_/      |
+           |       |              |
+           |       |              |
+           |    irq|------<-------'
+           |       |
+           '-------'
+
+Required properties:
+- compatible: Should be "axentia,tse850-envelope-detector"
+- io-channels: Channel node of the dac to be used for comparator input.
+- io-channel-names: Should be "dac".
+- interrupt specification for one client interrupt,
+  see ../../interrupt-controller/interrupts.txt for details.
+- interrupt-names: Should be "comp".
+
+Example:
+
+	&i2c {
+		dpot: mcp4651-104@28 {
+			compatible = "microchip,mcp4651-104";
+			reg = <0x28>;
+			#io-channel-cells = <1>;
+		};
+	};
+
+	dac: dac {
+		compatible = "dpot-dac";
+		vref-supply = <&reg_3v3>;
+		io-channels = <&dpot 0>;
+		io-channel-names = "dpot";
+		#io-channel-cells = <1>;
+	};
+
+	envelope-detector {
+		compatible = "axentia,tse850-envelope-detector";
+		io-channels = <&dac 0>;
+		io-channel-names = "dac";
+
+		interrupt-parent = <&gpio>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "comp";
+	};
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
new file mode 100644
index 000000000000..49ed82e89870
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
@@ -0,0 +1,83 @@
+STMicroelectronics STM32 ADC device driver
+
+STM32 ADC is a successive approximation analog-to-digital converter.
+It has several multiplexed input channels. Conversions can be performed
+in single, continuous, scan or discontinuous mode. Result of the ADC is
+stored in a left-aligned or right-aligned 32-bit data register.
+Conversions can be launched in software or using hardware triggers.
+
+The analog watchdog feature allows the application to detect if the input
+voltage goes beyond the user-defined, higher or lower thresholds.
+
+Each STM32 ADC block can have up to 3 ADC instances.
+
+Each instance supports two contexts to manage conversions, each one has its
+own configurable sequence and trigger:
+- regular conversion can be done in sequence, running in background
+- injected conversions have higher priority, and so have the ability to
+  interrupt regular conversion sequence (either triggered in SW or HW).
+  Regular sequence is resumed, in case it has been interrupted.
+
+Contents of a stm32 adc root node:
+-----------------------------------
+Required properties:
+- compatible: Should be "st,stm32f4-adc-core".
+- reg: Offset and length of the ADC block register set.
+- interrupts: Must contain the interrupt for ADC block.
+- clocks: Clock for the analog circuitry (common to all ADCs).
+- clock-names: Must be "adc".
+- interrupt-controller: Identifies the controller node as interrupt-parent
+- vref-supply: Phandle to the vref input analog reference voltage.
+- #interrupt-cells = <1>;
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- A pinctrl state named "default" for each ADC channel may be defined to set
+  inX ADC pins in mode of operation for analog input on external pin.
+
+Contents of a stm32 adc child node:
+-----------------------------------
+An ADC block node should contain at least one subnode, representing an
+ADC instance available on the machine.
+
+Required properties:
+- compatible: Should be "st,stm32f4-adc".
+- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200).
+- clocks: Input clock private to this ADC instance.
+- interrupt-parent: Phandle to the parent interrupt controller.
+- interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or
+  2 for adc@200).
+- st,adc-channels: List of single-ended channels muxed for this ADC.
+  It can have up to 16 channels, numbered from 0 to 15 (resp. for in0..in15).
+- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in
+  Documentation/devicetree/bindings/iio/iio-bindings.txt
+
+Example:
+	adc: adc@40012000 {
+		compatible = "st,stm32f4-adc-core";
+		reg = <0x40012000 0x400>;
+		interrupts = <18>;
+		clocks = <&rcc 0 168>;
+		clock-names = "adc";
+		vref-supply = <&reg_vref>;
+		interrupt-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&adc3_in8_pin>;
+
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@0 {
+			compatible = "st,stm32f4-adc";
+			#io-channel-cells = <1>;
+			reg = <0x0>;
+			clocks = <&rcc 0 168>;
+			interrupt-parent = <&adc>;
+			interrupts = <0>;
+			st,adc-channels = <8>;
+		};
+		...
+		other adc child nodes follow...
+	};
diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt
index 9ed2315781e4..3d25011f0c99 100644
--- a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt
+++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt
@@ -3,6 +3,7 @@
 Required properties:
  - compatible: Should be "ti,adc141s626" or "ti,adc161s626"
  - reg: spi chip select number for the device
+ - vdda-supply: supply voltage to VDDA pin
 
 Recommended properties:
  - spi-max-frequency: Definition as per
@@ -11,6 +12,7 @@ Recommended properties:
 Example:
 adc@0 {
 	compatible = "ti,adc161s626";
+	vdda-supply = <&vdda_fixed>;
 	reg = <0>;
 	spi-max-frequency = <4300000>;
 };
diff --git a/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt
new file mode 100644
index 000000000000..fdf47a01bfef
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt
@@ -0,0 +1,41 @@
+Bindings for DAC emulation using a digital potentiometer
+
+It is assumed that the dpot is used as a voltage divider between the
+current dpot wiper setting and the maximum resistance of the dpot. The
+divided voltage is provided by a vref regulator.
+
+                  .------.
+   .-----------.  |      |
+   | vref      |--'    .---.
+   | regulator |--.    |   |
+   '-----------'  |    | d |
+                  |    | p |
+                  |    | o |  wiper
+                  |    | t |<---------+
+                  |    |   |
+                  |    '---'       dac output voltage
+                  |      |
+                  '------+------------+
+
+Required properties:
+- compatible: Should be "dpot-dac"
+- vref-supply: The regulator supplying the voltage divider.
+- io-channels: Channel node of the dpot to be used for the voltage division.
+- io-channel-names: Should be "dpot".
+
+Example:
+
+	&i2c {
+		dpot: mcp4651-503@28 {
+			compatible = "microchip,mcp4651-503";
+			reg = <0x28>;
+			#io-channel-cells = <1>;
+		};
+	};
+
+	dac {
+		compatible = "dpot-dac";
+		vref-supply = <&reg_3v3>;
+		io-channels = <&dpot 0>;
+		io-channel-names = "dpot";
+	};
diff --git a/Documentation/devicetree/bindings/iio/dac/mcp4725.txt b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt
new file mode 100644
index 000000000000..1bc6c093fbfe
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt
@@ -0,0 +1,35 @@
+Microchip mcp4725 and mcp4726 DAC device driver
+
+Required properties:
+	- compatible: Must be "microchip,mcp4725" or "microchip,mcp4726"
+	- reg: Should contain the DAC I2C address
+	- vdd-supply: Phandle to the Vdd power supply. This supply is used as a
+	  voltage reference on mcp4725. It is used as a voltage reference on
+	  mcp4726 if there is no vref-supply specified.
+
+Optional properties (valid only for mcp4726):
+	- vref-supply: Optional phandle to the Vref power supply. Vref pin is
+	  used as a voltage reference when this supply is specified.
+	- microchip,vref-buffered: Boolean to enable buffering of the external
+	  Vref pin. This boolean is not valid without the vref-supply. Quoting
+	  the datasheet: This is offered in cases where the reference voltage
+	  does not have the current capability not to drop its voltage when
+	  connected to the internal resistor ladder circuit.
+
+Examples:
+
+	/* simple mcp4725 */
+	mcp4725@60 {
+		compatible = "microchip,mcp4725";
+		reg = <0x60>;
+		vdd-supply = <&vdac_vdd>;
+	};
+
+	/* mcp4726 with the buffered external reference voltage */
+	mcp4726@60 {
+		compatible = "microchip,mcp4726";
+		reg = <0x60>;
+		vdd-supply = <&vdac_vdd>;
+		vref-supply = <&vdac_vref>;
+		microchip,vref-buffered;
+	};
diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
new file mode 100644
index 000000000000..b0d3b59966bc
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt
@@ -0,0 +1,46 @@
+Invensense MPU-3050 Gyroscope device tree bindings
+
+Required properties:
+  - compatible : should be "invensense,mpu3050"
+  - reg : the I2C address of the sensor
+
+Optional properties:
+  - interrupt-parent : should be the phandle for the interrupt controller
+  - interrupts : interrupt mapping for the trigger interrupt from the
+    internal oscillator. The following IRQ modes are supported:
+    IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and
+    IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware
+    for the desired interrupt type.
+  - vdd-supply : supply regulator for the main power voltage.
+  - vlogic-supply : supply regulator for the signal voltage.
+  - mount-matrix : see iio/mount-matrix.txt
+
+Optional subnodes:
+  - The MPU-3050 will pass through and forward the I2C signals from the
+    incoming I2C bus, alternatively drive traffic to a slave device (usually
+    an accelerometer) on its own initiative. Therefore is supports a subnode
+    i2c gate node. For details see: i2c/i2c-gate.txt
+
+Example:
+
+mpu3050@68 {
+	compatible = "invensense,mpu3050";
+	reg = <0x68>;
+	interrupt-parent = <&foo>;
+	interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+	vdd-supply = <&bar>;
+	vlogic-supply = <&baz>;
+
+	/* External I2C interface */
+	i2c-gate {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fnord@18 {
+			compatible = "fnord";
+			reg = <0x18>;
+			interrupt-parent = <&foo>;
+			interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
new file mode 100644
index 000000000000..b20ab9c12080
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
@@ -0,0 +1,22 @@
+* HTS221 STM humidity + temperature sensor
+
+Required properties:
+- compatible: should be "st,hts221"
+- reg: i2c address of the sensor / spi cs line
+
+Optional properties:
+- interrupt-parent: should be the phandle for the interrupt controller
+- interrupts: interrupt mapping for IRQ. It should be configured with
+  flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING.
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt
+  client node bindings.
+
+Example:
+
+hts221@5f {
+	compatible = "st,hts221";
+	reg = <0x5f>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt
new file mode 100644
index 000000000000..425ab459e209
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/isl29018.txt
@@ -0,0 +1,28 @@
+* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor
+
+Required properties:
+
+  - compatible: Should be one of
+		"isil,isl29018"
+		"isil,isl29023"
+		"isil,isl29035"
+  - reg: the I2C address of the device
+
+Optional properties:
+
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+  - vcc-supply: phandle to the regulator that provides power to the sensor.
+
+Example:
+
+isl29018@44 {
+	compatible = "isil,isl29018";
+	reg = <0x44>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt
new file mode 100644
index 000000000000..8e2066c83f70
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt
@@ -0,0 +1,26 @@
+* TAOS TSL 2580/2581/2583 ALS sensor
+
+Required properties:
+
+  - compatible: Should be one of
+		"amstaos,tsl2580"
+		"amstaos,tsl2581"
+		"amstaos,tsl2583"
+  - reg: the I2C address of the device
+
+Optional properties:
+
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+  - vcc-supply: phandle to the regulator that provides power to the sensor.
+
+Example:
+
+tsl2581@29 {
+	compatible = "amstaos,tsl2581";
+	reg = <0x29>;
+};
diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt
new file mode 100644
index 000000000000..b9b621e94cd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt
@@ -0,0 +1,30 @@
+* Texas Instruments LMP91000 potentiostat
+
+http://www.ti.com/lit/ds/symlink/lmp91000.pdf
+
+Required properties:
+
+  - compatible: should be "ti,lmp91000"
+  - reg: the I2C address of the device
+  - io-channels: the phandle of the iio provider
+
+  - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this
+    needs to be set to signal that an external resistor value is being used.
+
+Optional properties:
+
+  - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance
+    amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms.
+
+  - ti,rload-ohm: ohm value of the internal resistor load applied to the gas
+    sensor. Must be 10, 33, 50, or 100 (default) ohms.
+
+Example:
+
+lmp91000@48 {
+	compatible = "ti,lmp91000";
+	reg = <0x48>;
+	ti,tia-gain-ohm = <7500>;
+	ti,rload = <100>;
+	io-channels = <&adc>;
+};
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
index e41fe340162b..c040c9ad1889 100644
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -42,6 +42,7 @@ Accelerometers:
 - st,lsm303agr-accel
 - st,lis2dh12-accel
 - st,h3lis331dl-accel
+- st,lng2dm-accel
 
 Gyroscopes:
 - st,l3g4200d-gyro
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index d9c51d7f4aac..56a257b7c4d7 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -39,6 +39,7 @@ auo	AU Optronics Corporation
 auvidea Auvidea GmbH
 avago	Avago Technologies
 avic	Shanghai AVIC Optoelectronics Co., Ltd.
+axentia	Axentia Technologies AB
 axis	Axis Communications AB
 boe	BOE Technology Group Co., Ltd.
 bosch	Bosch Sensortec GmbH
@@ -160,16 +161,19 @@ lltc	Linear Technology Corporation
 lsi	LSI Corp. (LSI Logic)
 marvell	Marvell Technology Group Ltd.
 maxim	Maxim Integrated Products
+mcube	mCube
 meas	Measurement Specialties
 mediatek	MediaTek Inc.
 melexis	Melexis N.V.
 melfas	MELFAS Inc.
+memsic	MEMSIC Inc.
 merrii	Merrii Technology Co., Ltd.
 micrel	Micrel Inc.
 microchip	Microchip Technology Inc.
 microcrystal	Micro Crystal AG
 micron	Micron Technology Inc.
 minix	MINIX Technology Ltd.
+miramems	MiraMEMS Sensing Technology Co., Ltd.
 mitsubishi	Mitsubishi Electric Corporation
 mosaixtech	Mosaix Technologies, Inc.
 moxa	Moxa