Merge branch 'wakeirq-8250' into omap-for-v4.2/wakeirq-v2

16 files changed, 134 insertions, 61 deletions

diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu
index 99983e67c13c..da95513571ea 100644
--- a/Documentation/ABI/testing/sysfs-devices-system-cpu
+++ b/Documentation/ABI/testing/sysfs-devices-system-cpu
@@ -162,7 +162,7 @@ Description:	Discover CPUs in the same CPU frequency coordination domain
 What:		/sys/devices/system/cpu/cpu*/cache/index3/cache_disable_{0,1}
 Date:		August 2008
 KernelVersion:	2.6.27
-Contact:	discuss@x86-64.org
+Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
 Description:	Disable L3 cache indices
 
 		These files exist in every CPU's cache/index3 directory. Each
diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
index c40711e8e8f7..28b28309f535 100644
--- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt
+++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
@@ -17,7 +17,8 @@ Required properties:
 - #clock-cells: from common clock binding; shall be set to 1.
 - clocks: from common clock binding; list of parent clock
   handles, shall be xtal reference clock or xtal and clkin for
-  si5351c only.
+  si5351c only. Corresponding clock input names are "xtal" and
+  "clkin" respectively.
 - #address-cells: shall be set to 1.
 - #size-cells: shall be set to 0.
 
@@ -71,6 +72,7 @@ i2c-master-node {
 
 		/* connect xtal input to 25MHz reference */
 		clocks = <&ref25>;
+		clock-names = "xtal";
 
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
index f20b111b502a..2bee68103b01 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
@@ -8,8 +8,8 @@ Required properties:
                is not Linux-only, but in case of Linux, see the "m25p_ids"
                table in drivers/mtd/devices/m25p80.c for the list of supported
                chips.
-               Must also include "nor-jedec" for any SPI NOR flash that can be
-               identified by the JEDEC READ ID opcode (0x9F).
+               Must also include "jedec,spi-nor" for any SPI NOR flash that can
+               be identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -25,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80", "nor-jedec";
+		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;
diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt
index abd67c13d344..4451ee973223 100644
--- a/Documentation/devicetree/bindings/net/cdns-emac.txt
+++ b/Documentation/devicetree/bindings/net/cdns-emac.txt
@@ -3,7 +3,8 @@
 Required properties:
 - compatible: Should be "cdns,[<chip>-]{emac}"
   Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  or the generic form: "cdns,emac".
+  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+  Or the generic form: "cdns,emac".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: see ethernet.txt file in the same directory.
diff --git a/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
new file mode 100644
index 000000000000..4163e7eb7763
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
@@ -0,0 +1,10 @@
+* ARM SBSA defined generic UART
+This UART uses a subset of the PL011 registers and consequently lives
+in the PL011 driver. It's baudrate and other communication parameters
+cannot be adjusted at runtime, so it lacks a clock specifier here.
+
+Required properties:
+- compatible: must be "arm,sbsa-uart"
+- reg: exactly one register range
+- interrupts: exactly one interrupt specifier
+- current-speed: the (fixed) baud rate set by the firmware
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index 44152261e5c5..8d63f1da07aa 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -14,7 +14,14 @@ Required properties:
 
 - interrupts: A single interrupt specifier.
 
-- clocks: Clock driving the hardware.
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names:
+  - "baud": The clock the baudrate is derived from
+  - "bus": The bus clock for register accesses (optional)
+
+For compatibility with older device trees an unnamed clock is used for the
+baud clock if the baudclk does not exist. Do not use this for new designs.
 
 Example:
 
@@ -22,5 +29,6 @@ Example:
 		compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart";
 		reg = <0x11006000 0x400>;
 		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
+		clocks = <&uart_clk>, <&bus_clk>;
+		clock-names = "baud", "bus";
 	};
diff --git a/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt
new file mode 100644
index 000000000000..04e23e63ee4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt
@@ -0,0 +1,28 @@
+* NXP LPC1850 UART
+
+Required properties:
+- compatible	: "nxp,lpc1850-uart", "ns16550a".
+- reg		: offset and length of the register set for the device.
+- interrupts	: should contain uart interrupt.
+- clocks	: phandle to the input clocks.
+- clock-names	: required elements: "uartclk", "reg".
+
+Optional properties:
+- dmas		: Two or more DMA channel specifiers following the
+		  convention outlined in bindings/dma/dma.txt
+- dma-names	: Names for the dma channels, if present. There must
+		  be at least one channel named "tx" for transmit
+		  and named "rx" for receive.
+
+Since it's also possible to also use the of_serial.c driver all
+parameters from 8250.txt also apply but are optional.
+
+Example:
+uart0: serial@40081000 {
+	compatible = "nxp,lpc1850-uart", "ns16550a";
+	reg = <0x40081000 0x1000>;
+	reg-shift = <2>;
+	interrupts = <24>;
+	clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+	clock-names = "uartclk", "reg";
+};
diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
index 246c795668dc..fbfe53635a3a 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
@@ -1,4 +1,5 @@
 * NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART)
+* i2c as bus
 
 Required properties:
 - compatible: Should be one of the following:
@@ -31,3 +32,39 @@ Example:
                 gpio-controller;
                 #gpio-cells = <2>;
         };
+
+* spi as bus
+
+Required properties:
+- compatible: Should be one of the following:
+  - "nxp,sc16is740" for NXP SC16IS740,
+  - "nxp,sc16is741" for NXP SC16IS741,
+  - "nxp,sc16is750" for NXP SC16IS750,
+  - "nxp,sc16is752" for NXP SC16IS752,
+  - "nxp,sc16is760" for NXP SC16IS760,
+  - "nxp,sc16is762" for NXP SC16IS762.
+- reg: SPI chip select number.
+- interrupt-parent: The phandle for the interrupt controller that
+  services interrupts for this IC.
+- interrupts: Specifies the interrupt source of the parent interrupt
+  controller. The format of the interrupt specifier depends on the
+  parent interrupt controller.
+- clocks: phandle to the IC source clock.
+
+Optional properties:
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be two. The first cell is the GPIO number and
+  the second cell is used to specify the GPIO polarity:
+    0 = active high,
+    1 = active low.
+
+Example:
+	sc16is750: sc16is750@0 {
+		compatible = "nxp,sc16is750";
+		reg = <0>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
index ae73bb0e9ad9..b91fcff4b7d4 100644
--- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
+++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
@@ -44,6 +44,11 @@ Required properties:
 Note: Each enabled SCIx UART should have an alias correctly numbered in the
 "aliases" node.
 
+Optional properties:
+  - dmas: Must contain a list of two references to DMA specifiers, one for
+	  transmission, and one for reception.
+  - dma-names: Must contain a list of two DMA names, "tx" and "rx".
+
 Example:
 	aliases {
 		serial0 = &scifa0;
@@ -56,4 +61,6 @@ Example:
 		interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>;
 		clock-names = "sci_ick";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
+		dma-names = "tx", "rx";
 	};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
index f0c39261c5d4..67e2a0aeb042 100644
--- a/Documentation/devicetree/bindings/serial/sirf-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -2,8 +2,7 @@
 
 Required properties:
 - compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart",
-		"sirf,atlas7-uart" or "sirf,atlas7-bt-uart" which means
-		uart located in BT module and used for BT.
+		"sirf,atlas7-uart" or "sirf,atlas7-usp-uart".
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain uart interrupt
 - fifosize : Should define hardware rx/tx fifo size
@@ -33,15 +32,3 @@ usp@b0090000 {
 	rts-gpios = <&gpio 15 0>;
 	cts-gpios = <&gpio 46 0>;
 };
-
-for uart use in BT module,
-uart6: uart@11000000 {
-	cell-index = <6>;
-	compatible = "sirf,atlas7-bt-uart", "sirf,atlas7-uart";
-	reg = <0x11000000 0x1000>;
-	interrupts = <0 100 0>;
-	clocks = <&clks 138>, <&clks 140>, <&clks 141>;
-	clock-names = "uart", "general", "noc";
-	fifosize = <128>;
-	status = "disabled";
-}
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index dc2a18f0b3a1..ddbe304beb21 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -15,10 +15,8 @@ Optional properties:
   - phys: phandle + phy specifier pair
   - phy-names: must be "usb"
   - dmas: Must contain a list of references to DMA specifiers.
-  - dma-names : Must contain a list of DMA names:
-   - tx0 ... tx<n>
-   - rx0 ... rx<n>
-    - This <n> means DnFIFO in USBHS module.
+  - dma-names : named "ch%d", where %d is the channel number ranging from zero
+                to the number of channels (DnFIFOs) minus one.
 
 Example:
 	usbhs: usb@e6590000 {
diff --git a/Documentation/hwmon/tmp401 b/Documentation/hwmon/tmp401
index 8eb88e974055..711f75e189eb 100644
--- a/Documentation/hwmon/tmp401
+++ b/Documentation/hwmon/tmp401
@@ -20,7 +20,7 @@ Supported chips:
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp432.html
   * Texas Instruments TMP435
     Prefix: 'tmp435'
-    Addresses scanned: I2C 0x37, 0x48 - 0x4f
+    Addresses scanned: I2C 0x48 - 0x4f
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
 
 Authors:
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 61ab1628a057..55bb093a08a3 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -959,14 +959,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 		uart[8250],io,<addr>[,options]
 		uart[8250],mmio,<addr>[,options]
 		uart[8250],mmio32,<addr>[,options]
+		uart[8250],mmio32be,<addr>[,options]
 		uart[8250],0x<addr>[,options]
 			Start an early, polled-mode console on the 8250/16550
 			UART at the specified I/O port or MMIO address.
 			MMIO inter-register address stride is either 8-bit
-			(mmio) or 32-bit (mmio32).
-			If none of [io|mmio|mmio32], <addr> is assumed to be
-			equivalent to 'mmio'. 'options' are specified in the
-			same format described for "console=ttyS<n>"; if
+			(mmio) or 32-bit (mmio32 or mmio32be).
+			If none of [io|mmio|mmio32|mmio32be], <addr> is assumed
+			to be equivalent to 'mmio'. 'options' are specified
+			in the same format described for "console=ttyS<n>"; if
 			unspecified, the h/w is not initialized.
 
 		pl011,<addr>
diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt
index 1e52d67d0abf..dbe6623fed1c 100644
--- a/Documentation/serial/tty.txt
+++ b/Documentation/serial/tty.txt
@@ -198,6 +198,9 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
+TTY_OTHER_DONE		Device is a pty and the other side has closed and
+			all pending input processing has been completed.
+
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 
diff --git a/Documentation/target/tcmu-design.txt b/Documentation/target/tcmu-design.txt
index 43e94ea6d2ca..263b907517ac 100644
--- a/Documentation/target/tcmu-design.txt
+++ b/Documentation/target/tcmu-design.txt
@@ -15,8 +15,7 @@ Contents:
   a) Discovering and configuring TCMU uio devices
   b) Waiting for events on the device(s)
   c) Managing the command ring
-3) Command filtering and pass_level
-4) A final note
+3) A final note
 
 
 TCM Userspace Design
@@ -324,7 +323,7 @@ int handle_device_events(int fd, void *map)
   /* Process events from cmd ring until we catch up with cmd_head */
   while (ent != (void *)mb + mb->cmdr_off + mb->cmd_head) {
 
-    if (tcmu_hdr_get_op(&ent->hdr) == TCMU_OP_CMD) {
+    if (tcmu_hdr_get_op(ent->hdr.len_op) == TCMU_OP_CMD) {
       uint8_t *cdb = (void *)mb + ent->req.cdb_off;
       bool success = true;
 
@@ -339,8 +338,12 @@ int handle_device_events(int fd, void *map)
         ent->rsp.scsi_status = SCSI_CHECK_CONDITION;
       }
     }
+    else if (tcmu_hdr_get_op(ent->hdr.len_op) != TCMU_OP_PAD) {
+      /* Tell the kernel we didn't handle unknown opcodes */
+      ent->hdr.uflags |= TCMU_UFLAG_UNKNOWN_OP;
+    }
     else {
-      /* Do nothing for PAD entries */
+      /* Do nothing for PAD entries except update cmd_tail */
     }
 
     /* update cmd_tail */
@@ -360,28 +363,6 @@ int handle_device_events(int fd, void *map)
 }
 
 
-Command filtering and pass_level
---------------------------------
-
-TCMU supports a "pass_level" option with valid values of 0 or 1.  When
-the value is 0 (the default), nearly all SCSI commands received for
-the device are passed through to the handler. This allows maximum
-flexibility but increases the amount of code required by the handler,
-to support all mandatory SCSI commands. If pass_level is set to 1,
-then only IO-related commands are presented, and the rest are handled
-by LIO's in-kernel command emulation. The commands presented at level
-1 include all versions of:
-
-READ
-WRITE
-WRITE_VERIFY
-XDWRITEREAD
-WRITE_SAME
-COMPARE_AND_WRITE
-SYNCHRONIZE_CACHE
-UNMAP
-
-
 A final note
 ------------
 
diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt
index 53838d9c6295..c59bd9bc41ef 100644
--- a/Documentation/virtual/kvm/mmu.txt
+++ b/Documentation/virtual/kvm/mmu.txt
@@ -169,6 +169,10 @@ Shadow pages contain the following information:
     Contains the value of cr4.smep && !cr0.wp for which the page is valid
     (pages for which this is true are different from other pages; see the
     treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
   gfn:
     Either the guest page table containing the translations shadowed by this
     page, or the base page frame for linear translations.  See role.direct.
@@ -344,10 +348,16 @@ on fault type:
 
 (user write faults generate a #PF)
 
-In the first case there is an additional complication if CR4.SMEP is
-enabled: since we've turned the page into a kernel page, the kernel may now
-execute it.  We handle this by also setting spte.nx.  If we get a user
-fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back.
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
 
 To prevent an spte that was converted into a kernel page with cr0.wp=0
 from being written by the kernel after cr0.wp has changed to 1, we make