Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "This patch set is a lot of driver updates for qla4xxx, bfa, hpsa,
  qla2xxx.  It also removes the aic7xxx_old driver (which has been
  deprecated for nearly a decade) and adds support for deadlines in
  error handling"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (75 commits)
  [SCSI] hpsa: allow SCSI mid layer to handle unit attention
  [SCSI] hpsa: do not require board "not ready" status after hard reset
  [SCSI] hpsa: enable unit attention reporting
  [SCSI] hpsa: rename scsi prefetch field
  [SCSI] hpsa: use workqueue instead of kernel thread for lockup detection
  [SCSI] ipr: increase dump size in ipr driver
  [SCSI] mac_scsi: Fix crash on out of memory
  [SCSI] st: fix enlarge_buffer
  [SCSI] qla1280: Annotate timer on stack so object debug does not complain
  [SCSI] qla4xxx: Update driver version to 5.04.00-k3
  [SCSI] qla4xxx: Recreate chap data list during get chap operation
  [SCSI] qla4xxx: Add support for ISCSI_PARAM_LOCAL_IPADDR sysfs attr
  [SCSI] libiscsi: Add local_ipaddr parameter in iscsi_conn struct
  [SCSI] scsi_transport_iscsi: Export ISCSI_PARAM_LOCAL_IPADDR attr for iscsi_connection
  [SCSI] qla4xxx: Add host statistics support
  [SCSI] scsi_transport_iscsi: Add host statistics support
  [SCSI] qla4xxx: Added support for Diagnostics MBOX command
  [SCSI] bfa: Driver version upgrade to 3.2.23.0
  [SCSI] bfa: change FC_ELS_TOV to 20sec
  [SCSI] bfa: Observed auto D-port mode instead of manual
  ...

4 files changed, 46 insertions, 545 deletions

diff --git a/Documentation/scsi/00-INDEX b/Documentation/scsi/00-INDEX
index 9b0787f965e9..2044be565d93 100644
--- a/Documentation/scsi/00-INDEX
+++ b/Documentation/scsi/00-INDEX
@@ -42,8 +42,6 @@ aic79xx.txt
 	- Adaptec Ultra320 SCSI host adapters
 aic7xxx.txt
 	- info on driver for Adaptec controllers
-aic7xxx_old.txt
-	- info on driver for Adaptec controllers, old generation
 arcmsr_spec.txt
 	- ARECA FIRMWARE SPEC (for IOP331 adapter)
 dc395x.txt
diff --git a/Documentation/scsi/aic7xxx_old.txt b/Documentation/scsi/aic7xxx_old.txt
deleted file mode 100644
index ecfc474f36a8..000000000000
--- a/Documentation/scsi/aic7xxx_old.txt
+++ /dev/null
@@ -1,511 +0,0 @@
-			    AIC7xxx Driver for Linux
-
-Introduction
-----------------------------
-The AIC7xxx SCSI driver adds support for Adaptec (http://www.adaptec.com)
-SCSI controllers and chipsets. Major portions of the driver and driver
-development are shared between both Linux and FreeBSD. Support for the
-AIC-7xxx chipsets have been in the default Linux kernel since approximately
-linux-1.1.x and fairly stable since linux-1.2.x, and are also in FreeBSD
-2.1.0 or later.
-
-  Supported cards/chipsets
-  ----------------------------
-    Adaptec Cards
-    ----------------------------
-    AHA-274x
-    AHA-274xT               
-    AHA-2842
-    AHA-2910B               
-    AHA-2920C
-    AHA-2930
-    AHA-2930U
-    AHA-2930CU
-    AHA-2930U2
-    AHA-2940               
-    AHA-2940W              
-    AHA-2940U              
-    AHA-2940UW
-    AHA-2940UW-PRO
-    AHA-2940AU 
-    AHA-2940U2W
-    AHA-2940U2
-    AHA-2940U2B
-    AHA-2940U2BOEM
-    AHA-2944D              
-    AHA-2944WD
-    AHA-2944UD
-    AHA-2944UWD
-    AHA-2950U2
-    AHA-2950U2W
-    AHA-2950U2B
-    AHA-29160M
-    AHA-3940
-    AHA-3940U
-    AHA-3940W
-    AHA-3940UW
-    AHA-3940AUW
-    AHA-3940U2W
-    AHA-3950U2B
-    AHA-3950U2D
-    AHA-3960D
-    AHA-39160M
-    AHA-3985
-    AHA-3985U
-    AHA-3985W
-    AHA-3985UW
-
-    Motherboard Chipsets
-    ----------------------------
-    AIC-777x   
-    AIC-785x
-    AIC-786x
-    AIC-787x
-    AIC-788x
-    AIC-789x
-    AIC-3860
-
-    Bus Types
-    ----------------------------
-    W - Wide SCSI, SCSI-3, 16bit bus, 68pin connector, will also support
-        SCSI-1/SCSI-2 50pin devices, transfer rates up to 20MB/s.
-    U - Ultra SCSI, transfer rates up to 40MB/s.
-    U2- Ultra 2 SCSI, transfer rates up to 80MB/s.
-    D - Differential SCSI.
-    T - Twin Channel SCSI. Up to 14 SCSI devices.
-
-    AHA-274x - EISA SCSI controller
-    AHA-284x - VLB SCSI controller
-    AHA-29xx - PCI SCSI controller
-    AHA-394x - PCI controllers with two separate SCSI controllers on-board.
-    AHA-398x - PCI RAID controllers with three separate SCSI controllers
-               on-board.
-
-  Not Supported Devices
-  ------------------------------
-    Adaptec Cards
-    ----------------------------
-    AHA-2920 (Only the cards that use the Future Domain chipset are not
-              supported, any 2920 cards based on Adaptec AIC chipsets,
-	      such as the 2920C, are supported)
-    AAA-13x Raid Adapters
-    AAA-113x Raid Port Card
-
-    Motherboard Chipsets
-    ----------------------------
-    AIC-7810
-
-    Bus Types
-    ----------------------------
-    R - Raid Port busses are not supported.
-
-    The hardware RAID devices sold by Adaptec are *NOT* supported by this
-    driver (and will people please stop emailing me about them, they are
-    a totally separate beast from the bare SCSI controllers and this driver
-    cannot be retrofitted in any sane manner to support the hardware RAID
-    features on those cards - Doug Ledford).
-    
-
-  People
-  ------------------------------
-    Justin T Gibbs  gibbs@plutotech.com
-      (BSD Driver Author)
-    Dan Eischen     deischen@iworks.InterWorks.org
-      (Original Linux Driver Co-maintainer)
-    Dean Gehnert    deang@teleport.com
-      (Original Linux FTP/patch maintainer)
-    Jess Johnson    jester@frenzy.com
-      (AIC7xxx FAQ author)
-    Doug Ledford    dledford@redhat.com
-      (Current Linux aic7xxx-5.x.x Driver/Patch/FTP maintainer)
-    
-    Special thanks go to John Aycock (aycock@cpsc.ucalgary.ca), the original
-    author of the driver. John has since retired from the project. Thanks
-    again for all his work!
-    
-  Mailing list
-  ------------------------------
-    There is a mailing list available for users who want to track development
-    and converse with other users and developers. This list is for both
-    FreeBSD and Linux support of the AIC7xxx chipsets.
-
-    To subscribe to the AIC7xxx mailing list send mail to the list server,
-    with "subscribe AIC7xxx" in the body (no Subject: required):
-        To: majordomo@FreeBSD.ORG
-        ---
-        subscribe AIC7xxx
-
-    To unsubscribe from the list, send mail to the list server with:
-        To: majordomo@FreeBSD.ORG
-        ---
-        unsubscribe AIC7xxx
-
-    Send regular messages and replies to: AIC7xxx@FreeBSD.ORG
-    
-  Boot Command line options
-  ------------------------------
-    "aic7xxx=no_reset" -  Eliminate the SCSI bus reset during startup.
-        Some SCSI devices need the initial reset that this option disables
-	in order to work.  If you have problems at bootup, please make sure
-	you aren't using this option.
-	
-    "aic7xxx=reverse_scan" - Certain PCI motherboards scan for devices at
-        bootup by scanning from the highest numbered PCI device to the
-	lowest numbered PCI device, others do just the opposite and scan
-	from lowest to highest numbered PCI device.  There is no reliable
-	way to autodetect this ordering.  So, we default to the most common
-	order, which is lowest to highest.  Then, in case your motherboard
-	scans from highest to lowest, we have this option.  If your BIOS
-	finds the drives on controller A before controller B but the linux
-	kernel finds your drives on controller B before A, then you should
-	use this option.
-	
-    "aic7xxx=extended" - Force the driver to detect extended drive translation
-        on your controller.  This helps those people who have cards without
-        a SEEPROM make sure that linux and all other operating systems think
-        the same way about your hard drives.
-
-    "aic7xxx=scbram" - Some cards have external SCB RAM that can be used to
-        give the card more hardware SCB slots.  This allows the driver to use
-	that SCB RAM.  Without this option, the driver won't touch the SCB
-	RAM because it is known to cause problems on a few cards out there
-	(such as 3985 class cards).
-	
-    "aic7xxx=irq_trigger:x" - Replace x with either 0 or 1 to force the kernel
-        to use the correct IRQ type for your card.  This only applies to EISA
-        based controllers.  On these controllers, 0 is for Edge triggered
-        interrupts, and 1 is for Level triggered interrupts.  If you aren't
-        sure or don't know which IRQ trigger type your EISA card uses, then
-        let the kernel autodetect the trigger type.
-	
-    "aic7xxx=verbose" - This option can be used in one of two ways.  If you
-        simply specify aic7xxx=verbose, then the kernel will automatically
-	pick the default set of verbose messages for you to see.
-	Alternatively, you can specify the command as 
-	"aic7xxx=verbose:0xXXXX" where the X entries are replaced with
-	hexadecimal digits.  This option is a bit field type option.  For
-	a full listing of the available options, search for the 
-	#define VERBOSE_xxxxxx lines in the aic7xxx.c file.  If you want
-	verbose messages, then it is recommended that you simply use the
-	aic7xxx=verbose variant of this command.
-	
-    "aic7xxx=pci_parity:x" - This option controls whether or not the driver
-        enables PCI parity error checking on the PCI bus.  By default, this
-        checking is disabled.  To enable the checks, simply specify pci_parity
-        with no value afterwords.  To reverse the parity from even to odd,
-        supply any number other than 0 or 255.  In short:
-          pci_parity     - Even parity checking (even is the normal PCI parity)
-          pci_parity:x   - Where x > 0, Odd parity checking
-          pci_parity:0   - No check (default)
-        NOTE: In order to get Even PCI parity checking, you must use the
-        version of the option that does not include the : and a number at
-        the end (unless you want to enter exactly 2^32 - 1 as the number).
-	
-    "aic7xxx=no_probe" - This option will disable the probing for any VLB
-        based 2842 controllers and any EISA based controllers.  This is
-	needed on certain newer motherboards where the normal EISA I/O ranges
-	have been claimed by other PCI devices.  Probing on those machines
-	will often result in the machine crashing or spontaneously rebooting
-	during startup.  Examples of machines that need this are the
-	Dell PowerEdge 6300 machines.
-
-    "aic7xxx=seltime:2" - This option controls how long the card waits
-        during a device selection sequence for the device to respond.
-	The original SCSI spec says that this "should be" 256ms.  This
-	is generally not required with modern devices.  However, some
-	very old SCSI I devices need the full 256ms.  Most modern devices
-	can run fine with only 64ms.  The default for this option is
-	64ms.  If you need to change this option, then use the following
-	table to set the proper value in the example above:
-	  0  -  256ms
-	  1  -  128ms
-	  2  -   64ms
-	  3  -   32ms
-	
-    "aic7xxx=panic_on_abort" - This option is for debugging and will cause
-        the driver to panic the linux kernel and freeze the system the first
-	time the drivers abort or reset routines are called.  This is most
-	helpful when some problem causes infinite reset loops that scroll too
-	fast to see.  By using this option, you can write down what the errors
-	actually are and send that information to me so it can be fixed.
-	
-    "aic7xxx=dump_card" - This option will print out the *entire* set of
-        configuration registers on the card during the init sequence.  This
-	is a debugging aid used to see exactly what state the card is in
-	when we finally finish our initialization routines.  If you don't
-	have documentation on the chipsets, this will do you absolutely
-	no good unless you are simply trying to write all the information
-	down in order to send it to me.
-	
-    "aic7xxx=dump_sequencer" - This is the same as the above options except
-        that instead of dumping the register contents on the card, this
-	option dumps the contents of the sequencer program RAM.  This gives
-	the ability to verify that the instructions downloaded to the
-	card's sequencer are indeed what they are supposed to be.  Again,
-	unless you have documentation to tell you how to interpret these
-	numbers, then it is totally useless.
-	
-    "aic7xxx=override_term:0xffffffff" - This option is used to force the
-    	termination on your SCSI controllers to a particular setting.  This
-	is a bit mask variable that applies for up to 8 aic7xxx SCSI channels.
-	Each channel gets 4 bits, divided as follows:
-	bit   3   2   1   0
-	      |   |   |   Enable/Disable Single Ended Low Byte Termination
-	      |   |   En/Disable Single Ended High Byte Termination
-	      |   En/Disable Low Byte LVD Termination
-	      En/Disable High Byte LVD Termination
-
-	The upper 2 bits that deal with LVD termination only apply to Ultra2
-	controllers.  Furthermore, due to the current Ultra2 controller
-	designs, these bits are tied together such that setting either bit
-	enables both low and high byte LVD termination.  It is not possible
-	to only set high or low byte LVD termination in this manner.  This is
-	an artifact of the BIOS definition on Ultra2 controllers.  For other
-	controllers, the only important bits are the two lowest bits.  Setting
-	the higher bits on non-Ultra2 controllers has no effect.  A few
-	examples of how to use this option:
-
-	Enable low and high byte termination on a non-ultra2 controller that
-	is the first aic7xxx controller (the correct bits are 0011), 
-	aic7xxx=override_term:0x3
-
-	Enable all termination on the third aic7xxx controller, high byte
-	termination on the second aic7xxx controller, and low and high byte
-	SE termination on the first aic7xxx controller 
-	(bits are 1111 0010 0011), 
-	aic7xxx=override_term:0xf23
-	
-	No attempt has been made to make this option non-cryptic.  It really
-	shouldn't be used except in dire circumstances, and if that happens,
-	I'm probably going to be telling you what to set this to anyway :)
-
-    "aic7xxx=stpwlev:0xffffffff" - This option is used to control the STPWLEV
-        bit in the DEVCONFIG PCI register.  Currently, this is one of the
-	very few registers that we have absolutely *no* way of detecting
-	what the variable should be.  It depends entirely on how the chipset
-	and external terminators were coupled by the card/motherboard maker.
-	Further, a chip reset (at power up) always sets this bit to 0.  If
-	there is no BIOS to run on the chipset/card (such as with a 2910C
-	or a motherboard controller with the BIOS totally disabled) then
-	the variable may not get set properly.  Of course, if the proper
-	setting was 0, then that's what it would be after the reset, but if
-	the proper setting is actually 1.....you get the picture.  Now, since
-	we can't detect this at all, I've added this option to force the
-	setting.  If you have a BIOS on your controller then you should never
-	need to use this option.  However, if you are having lots of SCSI
-	reset problems and can't seem to get them knocked out, this may help.
-
-	Here's a test to know for certain if you need this option.  Make
-	a boot floppy that you can use to boot your computer up and that
-	will detect the aic7xxx controller.  Next, power down your computer.
-	While it's down, unplug all SCSI cables from your Adaptec SCSI
-	controller.  Boot the system back up to the Adaptec EZ-SCSI BIOS
-	and then make sure that termination is enabled on your adapter (if
-	you have an Adaptec BIOS of course).  Next, boot up the floppy you
-	made and wait for it to detect the aic7xxx controller.  If the kernel
-	finds the controller fine, says scsi : x hosts and then tries to
-	detect your devices like normal, up to the point where it fails to
-	mount your root file system and panics, then you're fine.  If, on
-	the other hand, the system goes into an infinite reset loop, then
-	you need to use this option and/or the previous option to force the
-	proper termination settings on your controller.   If this happens,
-	then you next need to figure out what your settings should be.
-
-	To find the correct settings, power your machine back down, connect
-	back up the SCSI cables, and boot back into your machine like normal.
-	However, boot with the aic7xxx=verbose:0x39 option.  Record the
-	initial DEVCONFIG values for each of your aic7xxx controllers as
-	they are listed, and also record what the machine is detecting as
-	the proper termination on your controllers.  NOTE: the order in
-	which the initial DEVCONFIG values are printed out is not guaranteed
-	to be the same order as the SCSI controllers are registered.  The
-	above option and this option both work on the order of the SCSI
-	controllers as they are registered, so make sure you match the right
-	DEVCONFIG values with the right controllers if you have more than
-	one aic7xxx controller.
-
-	Once you have the detected termination settings and the initial
-	DEVCONFIG values for each controller, then figure out what the
-	termination on each of the controllers *should* be.  Hopefully, that
-	part is correct, but it could possibly be wrong if there is
-	bogus cable detection logic on your controller or something similar.
-	If all the controllers have the correct termination settings, then
-	don't set the aic7xxx=override_term variable at all, leave it alone.
-	Next, on any controllers that go into an infinite reset loop when
-	you unplug all the SCSI cables, get the starting DEVCONFIG value.
-	If the initial DEVCONFIG value is divisible by 2, then the correct
-	setting for that controller is 0.  If it's an odd number, then
-	the correct setting for that controller is 1.  For any other
-	controllers that didn't have an infinite reset problem, then reverse
-	the above options.  If DEVCONFIG was even, then the correct setting
-	is 1, if not then the correct setting is 0.
-
-	Now that you know what the correct setting was for each controller,
-	we need to encode that into the aic7xxx=stpwlev:0x... variable.
-	This variable is a bit field encoded variable.  Bit 0 is for the first
-	aic7xxx controller, bit 1 for the next, etc.  Put all these bits
-	together and you get a number.  For example, if the third aic7xxx
-	needed a 1, but the second and first both needed a 0, then the bits
-	would be 100 in binary.  This then translates to 0x04.  You would
-	therefore set aic7xxx=stpwlev:0x04.  This is fairly standard binary
-	to hexadecimal conversions here.  If you aren't up to speed on the
-	binary->hex conversion then send an email to the aic7xxx mailing
-	list and someone can help you out.
-
-    "aic7xxx=tag_info:{{8,8..},{8,8..},..}" - This option is used to disable
-        or enable Tagged Command Queueing (TCQ) on specific devices.  As of
-	driver version 5.1.11, TCQ is now either on or off by default
-	according to the setting you choose during the make config process.
-	In order to en/disable TCQ for certain devices at boot time, a user
-	may use this boot param.  The driver will then parse this message out
-        and en/disable the specific device entries that are present based upon
-        the value given.  The param line is parsed in the following manner:
-
-          { - first instance indicates the start of this parameter values
-              second instance is the start of entries for a particular
-              device entry
-          } - end the entries for a particular host adapter, or end the entire
-              set of parameter entries
-          , - move to next entry.  Inside of a set of device entries, this
-              moves us to the next device on the list.  Outside of device
-              entries, this moves us to the next host adapter
-          . - Same effect as , but is safe to use with insmod.
-          x - the number to enter into the array at this position.  
-              0 = Enable tagged queueing on this device and use the default
-                  queue depth
-              1-254 = Enable tagged queueing on this device and use this
-                      number as the queue depth
-              255 = Disable tagged queueing on this device.
-              Note: anything above 32 for an actual queue depth is wasteful
-                    and not recommended.
-
-        A few examples of how this can be used:
-
-        tag_info:{{8,12,,0,,255,4}}
-          This line will only effect the first aic7xxx card registered.  It
-          will set scsi id 0 to a queue depth of 8, id 1 to 12, leave id 2
-          at the default, set id 3 to tagged queueing enabled and use the
-          default queue depth, id 4 default, id 5 disabled, and id 6 to 4.
-          Any not specified entries stay at the default value, repeated
-          commas with no value specified will simply increment to the next id
-          without changing anything for the missing values.
-
-        tag_info:{,,,{,,,255}}
-          First, second, and third adapters at default values.  Fourth
-          adapter, id 3 is disabled.  Notice that leading commas simply
-	  increment what the first number effects, and there are no need
-	  for trailing commas.  When you close out an adapter, or the
-	  entire entry, anything not explicitly set stays at the default
-	  value.
-
-        A final note on this option.  The scanner I used for this isn't
-        perfect or highly robust.  If you mess the line up, the worst that
-        should happen is that the line will get ignored.  If you don't
-        close out the entire entry with the final bracket, then any other
-        aic7xxx options after this will get ignored.  So, in general, be
-        sure of what you are entering, and after you have it right, just
-        add it to the lilo.conf file so there won't be any mistakes.  As
-        a means of checking this parser, the entire tag_info array for
-        each card is now printed out in the /proc/scsi/aic7xxx/x file.  You
-        can use that to verify that your options were parsed correctly. 
-        
-    Boot command line options may be combined to form the proper set of options
-    a user might need.  For example, the following is valid:
-    
-    aic7xxx=verbose,extended,irq_trigger:1
-    
-    The only requirement is that individual options be separated by a comma or
-    a period on the command line.
-        
-  Module Loading command options
-  ------------------------------
-    When loading the aic7xxx driver as a module, the exact same options are
-    available to the user.  However, the syntax to specify the options changes
-    slightly.  For insmod, you need to wrap the aic7xxx= argument in quotes
-    and replace all ',' with '.'.  So, for example, a valid insmod line
-    would be:
-
-    insmod aic7xxx aic7xxx='verbose.irq_trigger:1.extended'
-
-    This line should result in the *exact* same behaviour as if you typed
-    it in at the lilo prompt and the driver was compiled into the kernel
-    instead of being a module.  The reason for the single quote is so that
-    the shell won't try to interpret anything in the line, such as {. 
-    Insmod assumes any options starting with a letter instead of a number
-    is a character string (which is what we want) and by switching all of
-    the commas to periods, insmod won't interpret this as more than one
-    string and write junk into our binary image.  I consider it a bug in
-    the insmod program that even if you wrap your string in quotes (quotes
-    that pass the shell mind you and that insmod sees) it still treats
-    a comma inside of those quotes as starting a new variable, resulting
-    in memory scribbles if you don't switch the commas to periods.
-
-
-  Kernel Compile options
-  ------------------------------
-    The various kernel compile time options for this driver are now fairly
-    well documented in the file drivers/scsi/Kconfig.  In order to
-    see this documentation, you need to use one of the advanced configuration
-    programs (menuconfig and xconfig).  If you are using the "make menuconfig"
-    method of configuring your kernel, then you would simply highlight the
-    option in question and hit the ? key.  If you are using the "make xconfig"
-    method of configuring your kernel, then simply click on the help button
-    next to the option you have questions about.  The help information from
-    the Configure.help file will then get automatically displayed.
-
-  /proc support
-  ------------------------------
-    The /proc support for the AIC7xxx can be found in the /proc/scsi/aic7xxx/
-    directory. That directory contains a file for each SCSI controller in
-    the system. Each file presents the current configuration and transfer
-    statistics (enabled with #define in aic7xxx.c) for each controller.
-
-    Thanks to Michael Neuffer for his upper-level SCSI help, and
-    Matthew Jacob for statistics support.
-
-  Debugging the driver
-  ------------------------------
-    Should you have problems with this driver, and would like some help in
-    getting them solved, there are a couple debugging items built into
-    the driver to facilitate getting the needed information from the system.
-    In general, I need a complete description of the problem, with as many
-    logs as possible concerning what happens.  To help with this, there is
-    a command option aic7xxx=panic_on_abort.  This option, when set, forces
-    the driver to panic the kernel on the first SCSI abort issued by the
-    mid level SCSI code.  If your system is going to reset loops and you
-    can't read the screen, then this is what you need.  Not only will it
-    stop the system, but it also prints out a large amount of state
-    information in the process.  Second, if you specify the option
-    "aic7xxx=verbose:0x1ffff", the system will print out *SOOOO* much
-    information as it runs that you won't be able to see anything.
-    However, this can actually be very useful if your machine simply
-    locks up when trying to boot, since it will pin-point what was last
-    happening (in regards to the aic7xxx driver) immediately prior to
-    the lockup.  This is really only useful if your machine simply can
-    not boot up successfully.  If you can get your machine to run, then
-    this will produce far too much information.
-
-  FTP sites
-  ------------------------------
-    ftp://ftp.redhat.com/pub/aic/
-      - Out of date.  I used to keep stuff here, but too many people
-        complained about having a hard time getting into Red Hat's ftp
-	server.  So use the web site below instead.
-    ftp://ftp.pcnet.com/users/eischen/Linux/
-      - Dan Eischen's driver distribution area
-    ftp://ekf2.vsb.cz/pub/linux/kernel/aic7xxx/ftp.teleport.com/
-      - European Linux mirror of Teleport site
-
-  Web sites
-  ------------------------------
-    http://people.redhat.com/dledford/
-      - My web site, also the primary aic7xxx site with several related
-        pages.
-
-Dean W. Gehnert
-deang@teleport.com
-
-$Revision: 3.0 $
-
-Modified by Doug Ledford 1998-2000
-
diff --git a/Documentation/scsi/scsi_eh.txt b/Documentation/scsi/scsi_eh.txt
index 6ff16b620d84..a0c85110a07e 100644
--- a/Documentation/scsi/scsi_eh.txt
+++ b/Documentation/scsi/scsi_eh.txt
@@ -42,20 +42,14 @@ discussion.
 
  Once LLDD gets hold of a scmd, either the LLDD will complete the
 command by calling scsi_done callback passed from midlayer when
-invoking hostt->queuecommand() or SCSI midlayer will time it out.
+invoking hostt->queuecommand() or the block layer will time it out.
 
 
 [1-2-1] Completing a scmd w/ scsi_done
 
  For all non-EH commands, scsi_done() is the completion callback.  It
-does the following.
-
- 1. Delete timeout timer.  If it fails, it means that timeout timer
-    has expired and is going to finish the command.  Just return.
-
- 2. Link scmd to per-cpu scsi_done_q using scmd->en_entry
-
- 3. Raise SCSI_SOFTIRQ
+just calls blk_complete_request() to delete the block layer timer and
+raise SCSI_SOFTIRQ
 
  SCSI_SOFTIRQ handler scsi_softirq calls scsi_decide_disposition() to
 determine what to do with the command.  scsi_decide_disposition()
@@ -64,10 +58,12 @@ with the command.
 
  - SUCCESS
 	scsi_finish_command() is invoked for the command.  The
-	function does some maintenance choirs and notify completion by
-	calling scmd->done() callback, which, for fs requests, would
-	be HLD completion callback - sd:sd_rw_intr, sr:rw_intr,
-	st:st_intr.
+	function does some maintenance chores and then calls
+	scsi_io_completion() to finish the I/O.
+	scsi_io_completion() then notifies the block layer on
+	the completed request by calling blk_end_request and
+	friends or figures out what to do with the remainder
+	of the data in case of an error.
 
  - NEEDS_RETRY
  - ADD_TO_MLQUEUE
@@ -86,33 +82,45 @@ function
  1. invokes optional hostt->eh_timed_out() callback.  Return value can
     be one of
 
-    - EH_HANDLED
-	This indicates that eh_timed_out() dealt with the timeout.  The
-	scmd is passed to __scsi_done() and thus linked into per-cpu
-	scsi_done_q.  Normal command completion described in [1-2-1]
-	follows.
+    - BLK_EH_HANDLED
+	This indicates that eh_timed_out() dealt with the timeout.
+	The command is passed back to the block layer and completed
+	via __blk_complete_requests().
+
+	*NOTE* After returning BLK_EH_HANDLED the SCSI layer is
+	assumed to be finished with the command, and no other
+	functions from the SCSI layer will be called. So this
+	should typically only be returned if the eh_timed_out()
+	handler raced with normal completion.
 
-    - EH_RESET_TIMER
+    - BLK_EH_RESET_TIMER
 	This indicates that more time is required to finish the
 	command.  Timer is restarted.  This action is counted as a
 	retry and only allowed scmd->allowed + 1(!) times.  Once the
-	limit is reached, action for EH_NOT_HANDLED is taken instead.
+	limit is reached, action for BLK_EH_NOT_HANDLED is taken instead.
 
-	*NOTE* This action is racy as the LLDD could finish the scmd
-	after the timeout has expired but before it's added back.  In
-	such cases, scsi_done() would think that timeout has occurred
-	and return without doing anything.  We lose completion and the
-	command will time out again.
-
-    - EH_NOT_HANDLED
-	This is the same as when eh_timed_out() callback doesn't exist.
+    - BLK_EH_NOT_HANDLED
+        eh_timed_out() callback did not handle the command.
 	Step #2 is taken.
 
+ 2. If the host supports asynchronous completion (as indicated by the
+    no_async_abort setting in the host template) scsi_abort_command()
+    is invoked to schedule an asynchrous abort. If that fails
+    Step #3 is taken.
+
  2. scsi_eh_scmd_add(scmd, SCSI_EH_CANCEL_CMD) is invoked for the
     command.  See [1-3] for more information.
 
+[1-3] Asynchronous command aborts
+
+ After a timeout occurs a command abort is scheduled from
+ scsi_abort_command(). If the abort is successful the command
+ will either be retried (if the number of retries is not exhausted)
+ or terminated with DID_TIME_OUT.
+ Otherwise scsi_eh_scmd_add() is invoked for the command.
+ See [1-4] for more information.
 
-[1-3] How EH takes over
+[1-4] How EH takes over
 
  scmds enter EH via scsi_eh_scmd_add(), which does the following.
 
@@ -320,7 +328,8 @@ scmd->allowed.
 
     <<scsi_eh_abort_cmds>>
 
-	This action is taken for each timed out command.
+	This action is taken for each timed out command when
+	no_async_abort is enabled in the host template.
 	hostt->eh_abort_handler() is invoked for each scmd.  The
 	handler returns SUCCESS if it has succeeded to make LLDD and
 	all related hardware forget about the scmd.
diff --git a/Documentation/scsi/scsi_mid_low_api.txt b/Documentation/scsi/scsi_mid_low_api.txt
index 2b06aba4fa0f..d6a9bdeee7f2 100644
--- a/Documentation/scsi/scsi_mid_low_api.txt
+++ b/Documentation/scsi/scsi_mid_low_api.txt
@@ -882,8 +882,11 @@ Details:
  *
  *      Calling context: kernel thread
  *
- *      Notes: Invoked from scsi_eh thread. No other commands will be
- *      queued on current host during eh.
+ *      Notes: If 'no_async_abort' is defined this callback
+ *  	will be invoked from scsi_eh thread. No other commands
+ *	will then be queued on current host during eh.
+ *	Otherwise it will be called whenever scsi_times_out()
+ *      is called due to a command timeout.
  *
  *      Optionally defined in: LLD
  **/
@@ -1257,6 +1260,8 @@ of interest:
                    address space
     use_clustering - 1=>SCSI commands in mid level's queue can be merged,
                      0=>disallow SCSI command merging
+    no_async_abort - 1=>Asynchronous aborts are not supported
+                     0=>Timed-out commands will be aborted asynchronously
     hostt        - pointer to driver's struct scsi_host_template from which
                    this struct Scsi_Host instance was spawned
     hostt->proc_name  - name of LLD. This is the driver name that sysfs uses