Merge tag 'spi-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Quite a quiet release for SPI, there are no changes at all to the core
  and not that many changes to drivers. Highlights of those driver
  changes include:

   - SH MSIOF support for GPIO chip selects contributed by Geert
     Uytterhoeven.

   - Full duplex support for a3700 contributed by Maxime Chevallier.

   - Support for DMA transfers on Atmel devices that require a bounce
     buffer contributed by Radu Pirea"

* tag 'spi-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (31 commits)
  spi: dw: Remove unused members from struct chip_data
  spi: orion: Fix a resource leak if the optional "axi" clk is deferred
  spi: a3700: Remove endianness swapping for full-duplex transfers
  spi: a3700: Remove endianness swapping functions when accessing FIFOs
  spi: a3700: Add full-duplex support
  spi: a3700: Allow to enable or disable FIFO mode
  spi: a3700: Set frequency limits at startup
  spi: a3700: Clear DATA_OUT when performing a read
  spi: orion: Fix clock resource by adding an optional bus clock
  spi: s3c64xx: add SPDX identifier
  spi: imx: do not access registers while clocks disabled
  spi: atmel: Implements transfers with bounce buffer
  spi: sh-msiof: Fix timeout failures for TX-only DMA transfers
  spi: spi-fsl-dspi: account for const type of of_device_id.data
  spi: bcm53xx: simplify reading SPI data
  spi: sirf: account for const type of of_device_id.data
  spi: pxa2xx: Use gpiod_put() not gpiod_free()
  spi: pxa2xx: avoid redundant gpio_to_desc(desc_to_gpio()) round-trip
  spi: sh-msiof: Document hardware limitations related to chip selects
  spi: sh-msiof: Implement cs-gpios configuration
  ...

4 files changed, 28 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt
index bdd83959019c..80710f0f0448 100644
--- a/Documentation/devicetree/bindings/spi/sh-msiof.txt
+++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt
@@ -36,7 +36,21 @@ Required properties:
 
 Optional properties:
 - clocks               : Must contain a reference to the functional clock.
-- num-cs               : Total number of chip-selects (default is 1)
+- num-cs               : Total number of chip selects (default is 1).
+			 Up to 3 native chip selects are supported:
+			   0: MSIOF_SYNC
+			   1: MSIOF_SS1
+			   2: MSIOF_SS2
+			 Hardware limitations related to chip selects:
+			   - Native chip selects are always deasserted in
+			     between transfers that are part of the same
+			     message.  Use cs-gpios to work around this.
+			   - All slaves using native chip selects must use the
+			     same spi-cs-high configuration.  Use cs-gpios to
+			     work around this.
+			   - When using GPIO chip selects, at least one native
+			     chip select must be left unused, as it will be
+			     driven anyway.
 - dmas                 : Must contain a list of two references to DMA
 			 specifiers, one for transmission, and one for
 			 reception.
diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt
index 825c39cae74a..b7f5e86fed22 100644
--- a/Documentation/devicetree/bindings/spi/spi-meson.txt
+++ b/Documentation/devicetree/bindings/spi/spi-meson.txt
@@ -27,7 +27,9 @@ The Meson SPICC is generic SPI controller for general purpose Full-Duplex
 communications with dedicated 16 words RX/TX PIO FIFOs.
 
 Required properties:
- - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs.
+ - compatible: should be:
+	"amlogic,meson-gx-spicc" on Amlogic GX and compatible SoCs.
+	"amlogic,meson-axg-spicc" on Amlogic AXG and compatible SoCs
  - reg: physical base address and length of the controller registers
  - interrupts: The interrupt specifier
  - clock-names: Must contain "core"
diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt
index df8ec31f2f07..8434a65fc12a 100644
--- a/Documentation/devicetree/bindings/spi/spi-orion.txt
+++ b/Documentation/devicetree/bindings/spi/spi-orion.txt
@@ -18,8 +18,17 @@ Required properties:
 	The eight register sets following the control registers refer to
 	chip-select lines 0 through 7 respectively.
 - cell-index : Which of multiple SPI controllers is this.
+- clocks : pointers to the reference clocks for this device, the first
+	   one is the one used for the clock on the spi bus, the
+	   second one is optional and is the clock used for the
+	   functional part of the controller
+
 Optional properties:
 - interrupts : Is currently not used.
+- clock-names : names of used clocks, mandatory if the second clock is
+		used, the name must be "core", and "axi" (the latter
+		is only for Armada 7K/8K).
+
 
 Example:
        spi@10600 {
diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt
index c7b7856bd528..7bf61efc66c8 100644
--- a/Documentation/devicetree/bindings/spi/spi-xilinx.txt
+++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt
@@ -2,7 +2,7 @@ Xilinx SPI controller Device Tree Bindings
 -------------------------------------------------
 
 Required properties:
-- compatible		: Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b"
+- compatible		: Should be "xlnx,xps-spi-2.00.a", "xlnx,xps-spi-2.00.b" or "xlnx,axi-quad-spi-1.00.a"
 - reg			: Physical base address and size of SPI registers map.
 - interrupts		: Property with a value describing the interrupt
 			  number.