Merge tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 4.21 cycle

Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST.  There has also been a good set of staging cleanup
in this period with more underway.

An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.

New device support,
* ad7124
  - New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
    with the inevitable DT binding.
* ad7949
  - New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
  - New driver supporting PNIs RM3100 magnometer with bindings and
    vendor prefix.
* ti-dac7311
  - New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
    DT bindings.
* vcnl5035
  - New driver supporting the light sensor part of the VCNL4035, with
    DT bindings

Features,
* bindings
  - Add a generic ADC channel binding as we keep reinventing this
    wheel.
* adc128s052
  - Add IDs for additional pin compatible parts.
  - Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
  - Allow for custom data register overiding default.
* kxcjk1013
  - Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
  - Rework leading to...
  - External sensor support using the built in I2C master.
  - Initial support for a slave lis2mdl magnetometer.
* meson-saradc
  - Add temperature sensor support and bindings.
* st_magn
  - New ID for lsm9dsl_magn with bindings
  - New ID for lis3de accelerometer
* tpl0102
  - Add supprot for IIO_AVAIL_RANGE to report the range available
    from this device to userspace and in kernel users.

Cleanups and minor fixes
* tools
  - Allow outside specification of CFLAGS
* ad2s90
  - Handle and spi_read error.
  - Handle spi_setup failure
  - Drop a pointless assignment.
  - Prevent a potentail race by moving device registration to after
    all other setup.
  - Add missing scale attribute.
  - Add a sanity check on channel type before trying to read it.
* ad2s1210
  - Move to modern gpio descriptors.
  - Drop a gpioin flag which made no sense as far as we can tell.
  - Add dt table (bindings doc to follow when this is ready for
    moving out of staging).
* ad5933
  - Drop camel-case naming of ext_clk_hz.
  - White space fixes.
* ad7150
  - Local variable to shorten overly long line.
  - Alignment and line break fixes.
* ad7280a
  - Handle an error path that was previously ignored.
  - Use crc8.h to build the crc table replacing custom code.
  - Avoid unecessary cast.
  - Power down the device if an error happens in probe
  - Use devm routines to simplify probe and remove.
* ad7606
  - Alignment fixes.
* ad7780
  - This worked as long as by coincidence an uninitialized value
    was 0.  Lets not rely on that.
  - Ensure gain update is only used with the ad778x chips that
    actually support it.
  - Tidy up pattern mask generation.
  - Read regulator when scale is requested (which should be infrequent)
    as it might have changed from initialization.
* ad7816
  - Move to modern gpio descriptors
  - Don't use a busy_pin for ad7818 as there isn't one.
  - Ensure RD/WR and CONVST pins are outputs (previously they
    were brought up as inputs which doesn't seem to make any sense)
  - DT id table.
* adc128s052
  - SPDX
* adt7316
  - Alignment fix.
  - Fix data reading.  When using I2C the driver never actually
    used the value read.  This has been broken a very long time
    hence no rush to fix it now + the driver is undergoing a lot
    of cleanup.
  - Sanity check that the i2c read didn't fail to actually read
    anything.
* dpot-dac
  - Mark a switch full through with slightly different text so that
    gcc doesn't warn on it.
* gyro-adc
  - Fix a wrong file in the MAINTAINERS entry and add binding doc to the
    listed files.
* ina2xx
  - Add some early returns to clarify error paths in switch.
* lsm6dsx
  - MAINTAINERS entry.
* max11100
  - SPDX
* max9611
  - SPDX
* mcp4131
  - use of_device_get_match_data in preference to spi_get_device_id
    approach.
* rcar-adc
  - SPDX
* sc27xx
  - Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
  - Don't free managed resources manually.
* st-magn
  - Add a comment to avoid future confusion over when to use -magn
    postfix (on multi chip in package parts)
  - Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
  - Minor spelling, grammar etc fixes.
* tpl0102
  - Use a pointer rather than an index of an array to improve conciseness.

* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
  Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
  Staging: iio: adt7316: Fix i2c data reading, set the data field
  dt-bindings: iio: adc: Add docs for ad7124
  iio: adc: Add ad7124 support
  dt-bindings: iio: adc: Add common ADCs properties to a separate file
  iio: ad_sigma_delta: Allow to provide custom data register address
  staging: iio: ad7816: Add device tree table.
  iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
  iio: potentiometer: mcp4131: use of_device_get_match_data()
  staging: iio: adc: ad7280a: use devm_* APIs
  staging: iio: adc: ad7280a: power down the device on error in probe
  dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
  iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
  iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
  iio: imu: st_lsm6dsx: add i2c embedded controller support
  iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
  iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
  iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
  iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
  iio: imu: st_lsm6dsx: introduce locked read/write utility routines
  ...

11 files changed, 194 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/iio/adc/ad7949.txt b/Documentation/devicetree/bindings/iio/adc/ad7949.txt
new file mode 100644
index 000000000000..c7f5057356b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ad7949.txt
@@ -0,0 +1,16 @@
+* Analog Devices AD7949/AD7682/AD7689
+
+Required properties:
+ - compatible: Should be one of
+	* "adi,ad7949"
+	* "adi,ad7682"
+	* "adi,ad7689"
+ - reg: spi chip select number for the device
+ - vref-supply: The regulator supply for ADC reference voltage
+
+Example:
+adc@0 {
+	compatible = "adi,ad7949";
+	reg = <0>;
+	vref-supply = <&vdd_supply>;
+};
diff --git a/Documentation/devicetree/bindings/iio/adc/adc.txt b/Documentation/devicetree/bindings/iio/adc/adc.txt
new file mode 100644
index 000000000000..5bbaa330a250
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adc.txt
@@ -0,0 +1,23 @@
+Common ADCs properties
+
+Optional properties for child nodes:
+- bipolar : Boolean, if set the channel is used in bipolar mode.
+- diff-channels : Differential channels muxed for this ADC. The first value
+		specifies the positive input pin, the second value the negative
+		input pin.
+
+Example:
+	adc@0 {
+		compatible = "some,adc";
+		...
+		channel@0 {
+			bipolar;
+			diff-channels = <0 1>;
+			...
+		};
+
+		channel@1 {
+			diff-channels = <2 3>;
+			...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
new file mode 100644
index 000000000000..416273dce569
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
@@ -0,0 +1,75 @@
+Analog Devices AD7124 ADC device driver
+
+Required properties for the AD7124:
+	- compatible: Must be one of "adi,ad7124-4" or "adi,ad7124-8"
+	- reg: SPI chip select number for the device
+	- spi-max-frequency: Max SPI frequency to use
+		see: Documentation/devicetree/bindings/spi/spi-bus.txt
+	- clocks: phandle to the master clock (mclk)
+		see: Documentation/devicetree/bindings/clock/clock-bindings.txt
+	- clock-names: Must be "mclk".
+	- interrupts: IRQ line for the ADC
+		see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+	  Required properties:
+		* #address-cells: Must be 1.
+		* #size-cells: Must be 0.
+
+	  Subnode(s) represent the external channels which are connected to the ADC.
+	  Each subnode represents one channel and has the following properties:
+		Required properties:
+			* reg: The channel number. It can have up to 4 channels on ad7124-4
+			  and 8 channels on ad7124-8, numbered from 0 to 15.
+			* diff-channels: see: Documentation/devicetree/bindings/iio/adc/adc.txt
+
+		Optional properties:
+			* bipolar: see: Documentation/devicetree/bindings/iio/adc/adc.txt
+			* adi,reference-select: Select the reference source to use when
+			  converting on the the specific channel. Valid values are:
+			  0: REFIN1(+)/REFIN1(−).
+			  1: REFIN2(+)/REFIN2(−).
+			  3: AVDD
+			  If this field is left empty, internal reference is selected.
+
+Optional properties:
+	- refin1-supply: refin1 supply can be used as reference for conversion.
+	- refin2-supply: refin2 supply can be used as reference for conversion.
+	- avdd-supply: avdd supply can be used as reference for conversion.
+
+Example:
+	adc@0 {
+		compatible = "adi,ad7124-4";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		interrupts = <25 2>;
+		interrupt-parent = <&gpio>;
+		refin1-supply = <&adc_vref>;
+		clocks = <&ad7124_mclk>;
+		clock-names = "mclk";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 {
+			reg = <0>;
+			diff-channels = <0 1>;
+			adi,reference-select = <0>;
+		};
+
+		channel@1 {
+			reg = <1>;
+			bipolar;
+			diff-channels = <2 3>;
+			adi,reference-select = <0>;
+		};
+
+		channel@2 {
+			reg = <2>;
+			diff-channels = <4 5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			diff-channels = <6 7>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt
index 54b823f3a453..325090e43ce6 100644
--- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt
@@ -22,6 +22,12 @@ Required properties:
 - vref-supply:	the regulator supply for the ADC reference voltage
 - #io-channel-cells: must be 1, see ../iio-bindings.txt
 
+Optional properties:
+- nvmem-cells:		phandle to the temperature_calib eFuse cells
+- nvmem-cell-names:	if present (to enable the temperature sensor
+			calibration) this must contain "temperature_calib"
+
+
 Example:
 	saradc: adc@8680 {
 		compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
index daa2b2c29428..c07ce1a3f5c4 100644
--- a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
+++ b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt
@@ -1,7 +1,14 @@
 * Texas Instruments' ADC128S052, ADC122S021 and ADC124S021 ADC chip
 
 Required properties:
- - compatible: Should be "ti,adc128s052", "ti,adc122s021" or "ti,adc124s021"
+ - compatible: Should be one of:
+   - "ti,adc128s052"
+   - "ti,adc122s021"
+   - "ti,adc122s051"
+   - "ti,adc122s101"
+   - "ti,adc124s021"
+   - "ti,adc124s051"
+   - "ti,adc124s101"
  - reg: spi chip select number for the device
  - vref-supply: The regulator supply for ADC reference voltage
 
diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt
new file mode 100644
index 000000000000..e5a507db5e01
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7311.txt
@@ -0,0 +1,23 @@
+TI DAC7311 device tree bindings
+
+Required properties:
+- compatible: must be set to:
+	* "ti,dac7311"
+	* "ti,dac6311"
+	* "ti,dac5311"
+- reg: spi chip select number for the device
+- vref-supply: The regulator supply for ADC reference voltage
+
+Optional properties:
+- spi-max-frequency: Max SPI frequency to use
+
+Example:
+
+	spi_master {
+		dac@0 {
+			compatible = "ti,dac7311";
+			reg = <0>; /* CS0 */
+			spi-max-frequency = <1000000>;
+			vref-supply = <&vdd_supply>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
index 879322ad50fd..69d53d98d0f0 100644
--- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
+++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
@@ -13,6 +13,7 @@ Required properties:
 Optional properties:
 - st,drdy-int-pin: the pin on the package that will be used to signal
   "data ready" (valid values: 1 or 2).
+- st,pullups : enable/disable internal i2c controller pullup resistors.
 - drive-open-drain: the interrupt/data ready line will be configured
   as open drain, which is useful if several sensors share the same
   interrupt line. This is a boolean property.
diff --git a/Documentation/devicetree/bindings/iio/light/vcnl4035.txt b/Documentation/devicetree/bindings/iio/light/vcnl4035.txt
new file mode 100644
index 000000000000..c07c7f052556
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/vcnl4035.txt
@@ -0,0 +1,18 @@
+VISHAY VCNL4035 -  Ambient Light and proximity sensor
+
+Link to datasheet: https://www.vishay.com/docs/84251/vcnl4035x01.pdf
+
+Required properties:
+
+	-compatible: should be "vishay,vcnl4035"
+	-reg: I2C address of the sensor, should be 0x60
+	-interrupts: interrupt mapping for GPIO IRQ (level active low)
+
+Example:
+
+light-sensor@60 {
+	compatible = "vishay,vcnl4035";
+	reg = <0x60>;
+	interrupt-parent = <&gpio4>;
+	interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
diff --git a/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt
new file mode 100644
index 000000000000..497c932e9e39
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt
@@ -0,0 +1,20 @@
+* PNI RM3100 3-axis magnetometer sensor
+
+Required properties:
+
+- compatible : should be "pni,rm3100"
+- reg : the I2C address or SPI chip select number of the sensor.
+
+Optional properties:
+
+- interrupts: data ready (DRDY) from the chip.
+  The interrupts can be triggered on level high.
+
+Example:
+
+rm3100: rm3100@20 {
+	compatible = "pni,rm3100";
+	reg = <0x20>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
index 6f626f73417e..ddcb95509599 100644
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -48,6 +48,7 @@ Accelerometers:
 - st,lis3l02dq
 - st,lis2dw12
 - st,lis3dhh
+- st,lis3de
 
 Gyroscopes:
 - st,l3g4200d-gyro
@@ -67,6 +68,7 @@ Magnetometers:
 - st,lsm303dlm-magn
 - st,lis3mdl-magn
 - st,lis2mdl
+- st,lsm9ds1-magn
 
 Pressure sensors:
 - st,lps001wp-press
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8fcc16..3cfe0c8b8250 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -303,6 +303,7 @@ pixcir  PIXCIR MICROELECTRONICS Co., Ltd
 plathome	Plat'Home Co., Ltd.
 plda	PLDA
 plx	Broadcom Corporation (formerly PLX Technology)
+pni	PNI Sensor Corporation
 portwell	Portwell Inc.
 poslab	Poslab Technology Co., Ltd.
 powervr	PowerVR (deprecated, use img)
@@ -415,6 +416,7 @@ vamrs	Vamrs Ltd.
 variscite	Variscite Ltd.
 via	VIA Technologies, Inc.
 virtio	Virtual I/O Device Specification, developed by the OASIS consortium
+vishay	Vishay Intertechnology, Inc
 vitesse	Vitesse Semiconductor Corporation
 vivante	Vivante Corporation
 vocore VoCore Studio