Merge tag 'rtc-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux

Pull RTC updates from Alexandre Belloni:
 "Subsystem wide cleanups:
   - Use IS_ENABLED() instead of checking for built-in or module
   - remove useless DRV_VERSION
   - remove CLK_IS_ROOT
   - remove UIE signaling

  Drivers:
   - ds1302: rewritten to be a proper SPI device driver
   - m41t80: huge cleanup, alarm, wakelarm ans oscialltor failure
     detection support
   - rv3029: switch to regmap to handle rv3049, alarm support, fixes
   - zynqmp: enable switching to battery power, fixes
   - small fixes for at91sam9, da9053, ds1307, ds1685, ds3232, r2025,
     sa1100, snvs, stmp3xxx, tps6586x"

* tag 'rtc-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (40 commits)
  rtc: tps6586x: rename so module can be autoloaded
  rtc: rv3029: hide unused i2c device table
  rtc: rs5c372: r2025: fix check for 'oscillator halted' condition
  rtc: rv3029: add alarm IRQ
  rtc: rv3029: fix set_time function
  rtc: rv3029: fix alarm support
  rtc: rv3029: Remove some checks and warnings
  rtc: rv3029: Add support of RV3049
  rtc: rv3029: convert to use regmap
  rtc: rv3029: remove 'i2c' in functions names
  rtc: stmp3xxx: print message on error
  rtc: Use IS_ENABLED() instead of checking for built-in or module
  rtc: ds3232: fix call trace when rtc->ops_lock is used as NULL
  rtc: snvs: return error in case enable_irq_wake fails
  rtc: zynqmp: Update seconds time programming logic
  rtc: sa1100: DT spelling s/interrupt-name/interrupt-names/
  rtc: mc13xxx: remove UIE signaling
  rtc: mxc: remove UIE signaling
  rtc: ds1307: Remove CLK_IS_ROOT
  rtc: hym8563: Remove CLK_IS_ROOT
  ...

2 files changed, 47 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt
new file mode 100644
index 000000000000..ba470c56cdec
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt
@@ -0,0 +1,46 @@
+* Maxim/Dallas Semiconductor DS-1302 RTC
+
+Simple device which could be used to store date/time between reboots.
+
+The device uses the standard MicroWire half-duplex transfer timing.
+Master output is set on low clock and sensed by the RTC on the rising
+edge. Master input is set by the RTC on the trailing edge and is sensed
+by the master on low clock.
+
+Required properties:
+
+- compatible : Should be "maxim,ds1302"
+
+Required SPI properties:
+
+- reg : Should be address of the device chip select within
+  the controller.
+
+- spi-max-frequency : DS-1302 has 500 kHz if powered at 2.2V,
+  and 2MHz if powered at 5V.
+
+- spi-3wire : The device has a shared signal IN/OUT line.
+
+- spi-lsb-first : DS-1302 requires least significant bit first
+  transfers.
+
+- spi-cs-high: DS-1302 has active high chip select line. This is
+  required unless inverted in hardware.
+
+Example:
+
+spi@901c {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "icpdas,lp8841-spi-rtc";
+	reg = <0x901c 0x1>;
+
+	rtc@0 {
+		compatible = "maxim,ds1302";
+		reg = <0>;
+		spi-max-frequency = <500000>;
+		spi-3wire;
+		spi-lsb-first;
+		spi-cs-high;
+	};
+};
diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt
index 0cda19ad4859..968ac820254b 100644
--- a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt
@@ -13,5 +13,5 @@ Example:
 		compatible = "mrvl,mmp-rtc";
 		reg = <0xd4010000 0x1000>;
 		interrupts = <5>, <6>;
-		interrupt-name = "rtc 1Hz", "rtc alarm";
+		interrupt-names = "rtc 1Hz", "rtc alarm";
 	};