Merge branch 'ti-dra7-dss' into 4.2/fbdev

Merge arch/ changes for TI's DRA7 SoC Display Subsystem.

15 files changed, 79 insertions, 46 deletions

diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu
index 99983e67c13c..da95513571ea 100644
--- a/Documentation/ABI/testing/sysfs-devices-system-cpu
+++ b/Documentation/ABI/testing/sysfs-devices-system-cpu
@@ -162,7 +162,7 @@ Description:	Discover CPUs in the same CPU frequency coordination domain
 What:		/sys/devices/system/cpu/cpu*/cache/index3/cache_disable_{0,1}
 Date:		August 2008
 KernelVersion:	2.6.27
-Contact:	discuss@x86-64.org
+Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
 Description:	Disable L3 cache indices
 
 		These files exist in every CPU's cache/index3 directory. Each
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt
index 653d5d739d7f..31d1d658827f 100644
--- a/Documentation/IPMI.txt
+++ b/Documentation/IPMI.txt
@@ -505,7 +505,10 @@ at module load time (for a module) with:
 
 The addresses are normal I2C addresses.  The adapter is the string
 name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name.
-It is *NOT* i2c-<n> itself.
+It is *NOT* i2c-<n> itself.  Also, the comparison is done ignoring
+spaces, so if the name is "This is an I2C chip" you can say
+adapter_name=ThisisanI2cchip.  This is because it's hard to pass in
+spaces in kernel parameters.
 
 The debug flags are bit flags for each BMC found, they are:
 IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8
diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt
index 750401f91341..15dfce708ebf 100644
--- a/Documentation/acpi/enumeration.txt
+++ b/Documentation/acpi/enumeration.txt
@@ -253,7 +253,7 @@ input driver:
 GPIO support
 ~~~~~~~~~~~~
 ACPI 5 introduced two new resources to describe GPIO connections: GpioIo
-and GpioInt. These resources are used be used to pass GPIO numbers used by
+and GpioInt. These resources can be used to pass GPIO numbers used by
 the device to the driver. ACPI 5.1 extended this with _DSD (Device
 Specific Data) which made it possible to name the GPIOs among other things.
 
diff --git a/Documentation/acpi/gpio-properties.txt b/Documentation/acpi/gpio-properties.txt
index ae36fcf86dc7..f35dad11f0de 100644
--- a/Documentation/acpi/gpio-properties.txt
+++ b/Documentation/acpi/gpio-properties.txt
@@ -1,9 +1,9 @@
 _DSD Device Properties Related to GPIO
 --------------------------------------
 
-With the release of ACPI 5.1 and the _DSD configuration objecte names
-can finally be given to GPIOs (and other things as well) returned by
-_CRS.  Previously, we were only able to use an integer index to find
+With the release of ACPI 5.1, the _DSD configuration object finally
+allows names to be given to GPIOs (and other things as well) returned
+by _CRS.  Previously, we were only able to use an integer index to find
 the corresponding GPIO, which is pretty error prone (it depends on
 the _CRS output ordering, for example).
 
diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
index 974624ea68f6..161448da959d 100644
--- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
+++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
@@ -6,6 +6,7 @@ provided by Arteris.
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+               Should be "ti,omap5-l3-noc" for OMAP5 family
 	       Should be "ti,dra7-l3-noc" for DRA7 family
                Should be "ti,am4372-l3-noc" for AM43 family
 - reg:	Contains L3 register address range for each noc domain.
diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
index c40711e8e8f7..28b28309f535 100644
--- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt
+++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt
@@ -17,7 +17,8 @@ Required properties:
 - #clock-cells: from common clock binding; shall be set to 1.
 - clocks: from common clock binding; list of parent clock
   handles, shall be xtal reference clock or xtal and clkin for
-  si5351c only.
+  si5351c only. Corresponding clock input names are "xtal" and
+  "clkin" respectively.
 - #address-cells: shall be set to 1.
 - #size-cells: shall be set to 0.
 
@@ -71,6 +72,7 @@ i2c-master-node {
 
 		/* connect xtal input to 25MHz reference */
 		clocks = <&ref25>;
+		clock-names = "xtal";
 
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;
diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
index a4873e5e3e36..e30e184f50c7 100644
--- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
@@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 {
 		      80 81 68 69
 		      70 71 72 73
 		      74 75 76 77>;
-	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+	interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 			  "saif0", "saif1", "i2c0", "i2c1",
 			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
index f20b111b502a..2bee68103b01 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
@@ -8,8 +8,8 @@ Required properties:
                is not Linux-only, but in case of Linux, see the "m25p_ids"
                table in drivers/mtd/devices/m25p80.c for the list of supported
                chips.
-               Must also include "nor-jedec" for any SPI NOR flash that can be
-               identified by the JEDEC READ ID opcode (0x9F).
+               Must also include "jedec,spi-nor" for any SPI NOR flash that can
+               be identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -25,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80", "nor-jedec";
+		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;
diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt
index abd67c13d344..4451ee973223 100644
--- a/Documentation/devicetree/bindings/net/cdns-emac.txt
+++ b/Documentation/devicetree/bindings/net/cdns-emac.txt
@@ -3,7 +3,8 @@
 Required properties:
 - compatible: Should be "cdns,[<chip>-]{emac}"
   Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  or the generic form: "cdns,emac".
+  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+  Or the generic form: "cdns,emac".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: see ethernet.txt file in the same directory.
diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
new file mode 100644
index 000000000000..be789685a1c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
@@ -0,0 +1,30 @@
+Abracon ABX80X I2C ultra low power RTC/Alarm chip
+
+The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
+ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
+is the superset of ab180x.
+
+Required properties:
+
+ - "compatible": should one of:
+        "abracon,abx80x"
+        "abracon,ab0801"
+        "abracon,ab0803"
+        "abracon,ab0804"
+        "abracon,ab0805"
+        "abracon,ab1801"
+        "abracon,ab1803"
+        "abracon,ab1804"
+        "abracon,ab1805"
+	Using "abracon,abx80x" will enable chip autodetection.
+ - "reg": I2C bus address of the device
+
+Optional properties:
+
+The abx804 and abx805 have a trickle charger that is able to charge the
+connected battery or supercap. Both the following properties have to be defined
+and valid to enable charging:
+
+ - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
+ - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
+                          resistor, the other values are in ohm.
diff --git a/Documentation/hwmon/tmp401 b/Documentation/hwmon/tmp401
index 8eb88e974055..711f75e189eb 100644
--- a/Documentation/hwmon/tmp401
+++ b/Documentation/hwmon/tmp401
@@ -20,7 +20,7 @@ Supported chips:
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp432.html
   * Texas Instruments TMP435
     Prefix: 'tmp435'
-    Addresses scanned: I2C 0x37, 0x48 - 0x4f
+    Addresses scanned: I2C 0x48 - 0x4f
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
 
 Authors:
diff --git a/Documentation/kasan.txt b/Documentation/kasan.txt
index 092fc10961fe..4692241789b1 100644
--- a/Documentation/kasan.txt
+++ b/Documentation/kasan.txt
@@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds
 bugs.
 
 KASan uses compile-time instrumentation for checking every memory access,
-therefore you will need a certain version of GCC > 4.9.2
+therefore you will need a gcc version of 4.9.2 or later. KASan could detect out
+of bounds accesses to stack or global variables, but only if gcc 5.0 or later was
+used to built the kernel.
 
 Currently KASan is supported only for x86_64 architecture and requires that the
 kernel be built with the SLUB allocator.
@@ -23,8 +25,8 @@ To enable KASAN configure kernel with:
 
 and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline
 is compiler instrumentation types. The former produces smaller binary the
-latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or
-latter.
+latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version
+of 5.0 or later.
 
 Currently KASAN works only with the SLUB memory allocator.
 For better bug detection and nicer report, enable CONFIG_STACKTRACE and put
diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt
index 1e52d67d0abf..dbe6623fed1c 100644
--- a/Documentation/serial/tty.txt
+++ b/Documentation/serial/tty.txt
@@ -198,6 +198,9 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
+TTY_OTHER_DONE		Device is a pty and the other side has closed and
+			all pending input processing has been completed.
+
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 
diff --git a/Documentation/target/tcmu-design.txt b/Documentation/target/tcmu-design.txt
index 43e94ea6d2ca..263b907517ac 100644
--- a/Documentation/target/tcmu-design.txt
+++ b/Documentation/target/tcmu-design.txt
@@ -15,8 +15,7 @@ Contents:
   a) Discovering and configuring TCMU uio devices
   b) Waiting for events on the device(s)
   c) Managing the command ring
-3) Command filtering and pass_level
-4) A final note
+3) A final note
 
 
 TCM Userspace Design
@@ -324,7 +323,7 @@ int handle_device_events(int fd, void *map)
   /* Process events from cmd ring until we catch up with cmd_head */
   while (ent != (void *)mb + mb->cmdr_off + mb->cmd_head) {
 
-    if (tcmu_hdr_get_op(&ent->hdr) == TCMU_OP_CMD) {
+    if (tcmu_hdr_get_op(ent->hdr.len_op) == TCMU_OP_CMD) {
       uint8_t *cdb = (void *)mb + ent->req.cdb_off;
       bool success = true;
 
@@ -339,8 +338,12 @@ int handle_device_events(int fd, void *map)
         ent->rsp.scsi_status = SCSI_CHECK_CONDITION;
       }
     }
+    else if (tcmu_hdr_get_op(ent->hdr.len_op) != TCMU_OP_PAD) {
+      /* Tell the kernel we didn't handle unknown opcodes */
+      ent->hdr.uflags |= TCMU_UFLAG_UNKNOWN_OP;
+    }
     else {
-      /* Do nothing for PAD entries */
+      /* Do nothing for PAD entries except update cmd_tail */
     }
 
     /* update cmd_tail */
@@ -360,28 +363,6 @@ int handle_device_events(int fd, void *map)
 }
 
 
-Command filtering and pass_level
---------------------------------
-
-TCMU supports a "pass_level" option with valid values of 0 or 1.  When
-the value is 0 (the default), nearly all SCSI commands received for
-the device are passed through to the handler. This allows maximum
-flexibility but increases the amount of code required by the handler,
-to support all mandatory SCSI commands. If pass_level is set to 1,
-then only IO-related commands are presented, and the rest are handled
-by LIO's in-kernel command emulation. The commands presented at level
-1 include all versions of:
-
-READ
-WRITE
-WRITE_VERIFY
-XDWRITEREAD
-WRITE_SAME
-COMPARE_AND_WRITE
-SYNCHRONIZE_CACHE
-UNMAP
-
-
 A final note
 ------------
 
diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt
index 53838d9c6295..c59bd9bc41ef 100644
--- a/Documentation/virtual/kvm/mmu.txt
+++ b/Documentation/virtual/kvm/mmu.txt
@@ -169,6 +169,10 @@ Shadow pages contain the following information:
     Contains the value of cr4.smep && !cr0.wp for which the page is valid
     (pages for which this is true are different from other pages; see the
     treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
   gfn:
     Either the guest page table containing the translations shadowed by this
     page, or the base page frame for linear translations.  See role.direct.
@@ -344,10 +348,16 @@ on fault type:
 
 (user write faults generate a #PF)
 
-In the first case there is an additional complication if CR4.SMEP is
-enabled: since we've turned the page into a kernel page, the kernel may now
-execute it.  We handle this by also setting spte.nx.  If we get a user
-fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back.
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
 
 To prevent an spte that was converted into a kernel page with cr0.wp=0
 from being written by the kernel after cr0.wp has changed to 1, we make