ARM: dts: bcm2837: Add Raspberry Pi 3 B+

The Raspberry Pi 3 B+ has the following major differences compared
to the model 3 B:
* Microchip LAN7515 (Gigabit Ethernet with integrated USB 2.0 HUB)
* Cypress CYW43455 (802.11n/ac and BT 4.2)

We need to add the USB LAN chip so the bootloader can add the MAC address.
This is necessary because there ain't an EEPROM or a valid OTP.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>

1 files changed, 108 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 000000000000..4adb85e66be3
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "STATUS_LED",
+				  "LAN_RUN",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};