ARM: dts: Add support for sbc-3xxx with cm-t3730

This adds support for CompuLab SBC-T3530, also known as cm-t3730:

http://compulab.co.il/products/sbcs/sbc-t3530/

It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:

http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/

So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.

I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.

Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.

Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 95 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
new file mode 100644
index 000000000000..3a9f004d8924
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -0,0 +1,95 @@
+/*
+ * Common support for CompuLab CM-T3530 and  CM-T3730
+ */
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ledb {
+			label = "cm-t35:green";
+			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vddvario: regulator-vddvario {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>;
+
+	smsc1: ethernet@5,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		interrupt-parent = <&gpio6>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		reg = <5 0 0xff>;
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+};