ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi

Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.

Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.

My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.

Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 14 insertions, 648 deletions

diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index f10b42fa15c6..05b1c1ebded8 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -7,9 +7,7 @@
  */
 /dts-v1/;
 
-#include "omap5.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "omap5-board-common.dtsi"
 
 / {
 	model = "TI OMAP5 uEVM board";
@@ -19,572 +17,10 @@
 		device_type = "memory";
 		reg = <0x80000000 0x7F000000>; /* 2032 MB */
 	};
-
-	aliases {
-		display0 = &hdmi0;
-	};
-
-	vmmcsd_fixed: fixedregulator-mmcsd {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsd_fixed";
-		regulator-min-microvolt = <3000000>;
-		regulator-max-microvolt = <3000000>;
-	};
-
-	mmc3_pwrseq: sdhci0_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		clocks = <&clk32kgaudio>;
-		clock-names = "ext_clock";
-	};
-
-	vmmcsdio_fixed: fixedregulator-mmcsdio {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsdio_fixed";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>;	/* gpio140 WLAN_EN */
-		enable-active-high;
-		startup-delay-us = <70000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_pins>;
-	};
-
-	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
-		compatible = "usb-nop-xceiv";
-		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-		clocks = <&auxclk1_ck>;
-		clock-names = "main_clk";
-		clock-frequency = <19200000>;
-	};
-
-	/* HS USB Host PHY on PORT 3 */
-	hsusb3_phy: hsusb3_phy {
-		compatible = "usb-nop-xceiv";
-		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		led@1 {
-			label = "omap5:blue:usr1";
-			gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
-	tpd12s015: encoder@0 {
-		compatible = "ti,tpd12s015";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tpd12s015_pins>;
-
-		gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>,	/* TCA6424A P01, CT CP HPD */
-			<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
-			<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint@0 {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint@0 {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	hdmi0: connector@0 {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "b";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-
-	sound: sound {
-		compatible = "ti,abe-twl6040";
-		ti,model = "omap5-uevm";
-
-		ti,mclk-freq = <19200000>;
-
-		ti,mcpdm = <&mcpdm>;
-
-		ti,twl6040 = <&twl6040>;
-
-		/* Audio routing */
-		ti,audio-routing =
-			"Headset Stereophone", "HSOL",
-			"Headset Stereophone", "HSOR",
-			"Line Out", "AUXL",
-			"Line Out", "AUXR",
-			"HSMIC", "Headset Mic",
-			"Headset Mic", "Headset Mic Bias",
-			"AFML", "Line In",
-			"AFMR", "Line In";
-	};
-};
-
-&omap5_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&usbhost_pins
-			&led_gpio_pins
-	>;
-
-	twl6040_pins: pinmux_twl6040_pins {
-		pinctrl-single,pins = <
-			0x17e (PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
-		>;
-	};
-
-	mcpdm_pins: pinmux_mcpdm_pins {
-		pinctrl-single,pins = <
-			0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
-			0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_ul_data.abemcpdm_ul_data */
-			0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_dl_data.abemcpdm_dl_data */
-			0x160 (PIN_INPUT_PULLUP | MUX_MODE0)	/* abemcpdm_frame.abemcpdm_frame */
-			0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_lb_clk.abemcpdm_lb_clk */
-		>;
-	};
-
-	mcbsp1_pins: pinmux_mcbsp1_pins {
-		pinctrl-single,pins = <
-			0x14c (PIN_INPUT | MUX_MODE1)		/* abedmic_clk2.abemcbsp1_fsx */
-			0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* abedmic_clk3.abemcbsp1_dx */
-			0x150 (PIN_INPUT | MUX_MODE1)		/* abeslimbus1_clock.abemcbsp1_clkx */
-			0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* abeslimbus1_data.abemcbsp1_dr */
-		>;
-	};
-
-	mcbsp2_pins: pinmux_mcbsp2_pins {
-		pinctrl-single,pins = <
-			0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dr.abemcbsp2_dr */
-			0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dx.abemcbsp2_dx */
-			0x158 (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_fsx.abemcbsp2_fsx */
-			0x15a (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_clkx.abemcbsp2_clkx */
-		>;
-	};
-
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
-			0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
-		>;
-	};
-
-	i2c5_pins: pinmux_i2c5_pins {
-		pinctrl-single,pins = <
-			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
-			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
-		>;
-	};
-
-	mcspi2_pins: pinmux_mcspi2_pins {
-		pinctrl-single,pins = <
-			0xbc (PIN_INPUT | MUX_MODE0)		/*  mcspi2_clk */
-			0xbe (PIN_INPUT | MUX_MODE0)		/*  mcspi2_simo */
-			0xc0 (PIN_INPUT_PULLUP | MUX_MODE0)	/*  mcspi2_somi */
-			0xc2 (PIN_OUTPUT | MUX_MODE0)		/*  mcspi2_cs0 */
-		>;
-	};
-
-	mcspi3_pins: pinmux_mcspi3_pins {
-		pinctrl-single,pins = <
-			0x78 (PIN_INPUT | MUX_MODE1)		/*  mcspi3_somi */
-			0x7a (PIN_INPUT | MUX_MODE1)		/*  mcspi3_cs0 */
-			0x7c (PIN_INPUT | MUX_MODE1)		/*  mcspi3_simo */
-			0x7e (PIN_INPUT | MUX_MODE1)		/*  mcspi3_clk */
-		>;
-	};
-
-	mmc3_pins: pinmux_mmc3_pins {
-		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
-			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
-			OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
-			OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
-			OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
-			OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
-		>;
-	};
-
-	wlan_pins: pinmux_wlan_pins {
-		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
-		>;
-	};
-
-	usbhost_pins: pinmux_usbhost_pins {
-		pinctrl-single,pins = <
-			0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
-			0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
-
-			0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
-			0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
-
-			0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
-			0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
-		>;
-	};
-
-	led_gpio_pins: pinmux_led_gpio_pins {
-		pinctrl-single,pins = <
-			0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
-		>;
-	};
-
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-			0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
-			0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
-			0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
-			0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
-			0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
-		>;
-	};
-
-	uart5_pins: pinmux_uart5_pins {
-		pinctrl-single,pins = <
-			0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
-			0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
-			0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
-			0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
-		>;
-	};
-
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-			0x0fc (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_cec.hdmi_cec */
-			0x100 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_scl.hdmi_ddc_scl */
-			0x102 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_sda.hdmi_ddc_sda */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6)	/* hdmi_hpd.gpio7_193 */
-		>;
-	};
 };
 
-&omap5_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&usbhost_wkup_pins
-	>;
-
-	usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
-		pinctrl-single,pins = <
-			0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
-		>;
-	};
-
-	wlcore_irq_pin: pinmux_wlcore_irq_pin {
-		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
-		>;
-	};
-};
-
-&mmc1 {
-	vmmc-supply = <&ldo9_reg>;
-	bus-width = <4>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <8>;
-	ti,non-removable;
-};
-
-&mmc3 {
-	vmmc-supply = <&vmmcsdio_fixed>;
-	mmc-pwrseq = <&mmc3_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	cap-power-off-card;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
-	interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
-			       &omap5_pmx_core 0x168>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1271";
-		reg = <2>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;	/* gpio 14 */
-		ref-clock-frequency = <26000000>;
-	};
-};
-
-&mmc4 {
-	status = "disabled";
-};
-
-&mmc5 {
-	status = "disabled";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-
-	clock-frequency = <400000>;
-
-	palmas: palmas@48 {
-		compatible = "ti,palmas";
-		interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
-		reg = <0x48>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		ti,system-power-controller;
-
-		extcon_usb3: palmas_usb {
-			compatible = "ti,palmas-usb-vid";
-			ti,enable-vbus-detection;
-			ti,enable-id-detection;
-			ti,wakeup;
-		};
-
-		clk32kgaudio: palmas_clk32k@1 {
-			compatible = "ti,palmas-clk32kgaudio";
-			#clock-cells = <0>;
-		};
-
-		palmas_pmic {
-			compatible = "ti,palmas-pmic";
-			interrupt-parent = <&palmas>;
-			interrupts = <14 IRQ_TYPE_NONE>;
-			interrupt-name = "short-irq";
-
-			ti,ldo6-vibrator;
-
-			regulators {
-				smps123_reg: smps123 {
-					/* VDD_OPP_MPU */
-					regulator-name = "smps123";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps45_reg: smps45 {
-					/* VDD_OPP_MM */
-					regulator-name = "smps45";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1310000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps6_reg: smps6 {
-					/* VDD_DDR3 - over VDD_SMPS6 */
-					regulator-name = "smps6";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps7_reg: smps7 {
-					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
-					regulator-name = "smps7";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps8_reg: smps8 {
-					/* VDD_OPP_CORE */
-					regulator-name = "smps8";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1310000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps9_reg: smps9 {
-					/* VDDA_2v1_AUD over VDD_2v1 */
-					regulator-name = "smps9";
-					regulator-min-microvolt = <2100000>;
-					regulator-max-microvolt = <2100000>;
-					ti,smps-range = <0x80>;
-				};
-
-				smps10_out2_reg: smps10_out2 {
-					/* VBUS_5V_OTG */
-					regulator-name = "smps10_out2";
-					regulator-min-microvolt = <5000000>;
-					regulator-max-microvolt = <5000000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps10_out1_reg: smps10_out1 {
-					/* VBUS_5V_OTG */
-					regulator-name = "smps10_out1";
-					regulator-min-microvolt = <5000000>;
-					regulator-max-microvolt = <5000000>;
-				};
-
-				ldo1_reg: ldo1 {
-					/* VDDAPHY_CAM: vdda_csiport */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo2_reg: ldo2 {
-					/* VCC_2V8_DISP: Does not go anywhere */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					/* Unused */
-					status = "disabled";
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDAPHY_MDM: vdda_lli */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-boot-on;
-					/* Only if Modem is used */
-					status = "disabled";
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo5_reg: ldo5 {
-					/* VDDA_1V8_PHY: usb/sata/hdmi.. */
-					regulator-name = "ldo5";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo6_reg: ldo6 {
-					/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
-					regulator-name = "ldo6";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo7_reg: ldo7 {
-					/* VDD_VPP: vpp1 */
-					regulator-name = "ldo7";
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					/* Only for efuse reprograming! */
-					status = "disabled";
-				};
-
-				ldo8_reg: ldo8 {
-					/* VDD_3v0: Does not go anywhere */
-					regulator-name = "ldo8";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-boot-on;
-					/* Unused */
-					status = "disabled";
-				};
-
-				ldo9_reg: ldo9 {
-					/* VCC_DV_SDIO: vdds_sdcard */
-					regulator-name = "ldo9";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-boot-on;
-				};
-
-				ldoln_reg: ldoln {
-					/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
-					regulator-name = "ldoln";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldousb_reg: ldousb {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldousb";
-					regulator-min-microvolt = <3250000>;
-					regulator-max-microvolt = <3250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				regen3_reg: regen3 {
-					/* REGEN3 controls LDO9 supply to card */
-					regulator-name = "regen3";
-					regulator-always-on;
-					regulator-boot-on;
-				};
-			};
-		};
-
-		palmas_power_button: palmas_power_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&palmas>;
-			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-		};
-	};
-
-	twl6040: twl@4b {
-		compatible = "ti,twl6040";
-		reg = <0x4b>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&twl6040_pins>;
-
-		interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
-		ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
-
-		vio-supply = <&smps7_reg>;
-		v2v1-supply = <&smps9_reg>;
-		enable-active-high;
-
-		clocks = <&clk32kgaudio>;
-		clock-names = "clk32k";
-	};
+&hdmi {
+	vdda-supply = <&ldo4_reg>;
 };
 
 &i2c5 {
@@ -601,87 +37,17 @@
 	};
 };
 
-&mcpdm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcpdm_pins>;
-	status = "okay";
-};
-
-&mcbsp1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp1_pins>;
-	status = "okay";
-};
-
-&mcbsp2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp2_pins>;
-	status = "okay";
-};
-
-&usbhshost {
-	port2-mode = "ehci-hsic";
-	port3-mode = "ehci-hsic";
-};
-
-&usbhsehci {
-	phys = <0 &hsusb2_phy &hsusb3_phy>;
-};
-
-&usb3 {
-	extcon = <&extcon_usb3>;
-	vbus-supply = <&smps10_out1_reg>;
-};
-
-&mcspi1 {
-
-};
-
-&mcspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi2_pins>;
-};
-
-&mcspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi3_pins>;
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
-	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-			      <&omap5_pmx_core 0x19c>;
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart5_pins>;
-};
-
-&cpu0 {
-	cpu0-supply = <&smps123_reg>;
-};
-
-&dss {
-	status = "ok";
+&omap5_pmx_core {
+	i2c5_pins: pinmux_i2c5_pins {
+		pinctrl-single,pins = <
+			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
+			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
+		>;
+	};
 };
 
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo4_reg>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&dss_hdmi_pins>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
+&tpd12s015 {
+	gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>,	/* TCA6424A P01, CT CP HPD */
+		<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
+		<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
 };