[ARM] 4940/1: AT91: UDPHS driver: SAM9RL board and cpu integration.

Adds support for the USB High Speed Device Port on the AT91SAM9RL
system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and
the AT91CAP9 (atmel_usba_udc driver).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 95 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 450db304936f..8507dd02fe90 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -26,6 +26,101 @@
 
 
 /* --------------------------------------------------------------------
+ *  USB HS Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE)
+
+static struct resource usba_udc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9RL_UDPHS_FIFO,
+		.end	= AT91SAM9RL_UDPHS_FIFO + SZ_512K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9RL_BASE_UDPHS,
+		.end	= AT91SAM9RL_BASE_UDPHS + SZ_1K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= AT91SAM9RL_ID_UDPHS,
+		.end	= AT91SAM9RL_ID_UDPHS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+#define EP(nam, idx, maxpkt, maxbk, dma, isoc)			\
+	[idx] = {						\
+		.name		= nam,				\
+		.index		= idx,				\
+		.fifo_size	= maxpkt,			\
+		.nr_banks	= maxbk,			\
+		.can_dma	= dma,				\
+		.can_isoc	= isoc,				\
+	}
+
+static struct usba_ep_data usba_udc_ep[] __initdata = {
+	EP("ep0", 0, 64, 1, 0, 0),
+	EP("ep1", 1, 1024, 2, 1, 1),
+	EP("ep2", 2, 1024, 2, 1, 1),
+	EP("ep3", 3, 1024, 3, 1, 0),
+	EP("ep4", 4, 1024, 3, 1, 0),
+	EP("ep5", 5, 1024, 3, 1, 1),
+	EP("ep6", 6, 1024, 3, 1, 1),
+};
+
+#undef EP
+
+/*
+ * pdata doesn't have room for any endpoints, so we need to
+ * append room for the ones we need right after it.
+ */
+static struct {
+	struct usba_platform_data pdata;
+	struct usba_ep_data ep[7];
+} usba_udc_data;
+
+static struct platform_device at91_usba_udc_device = {
+	.name		= "atmel_usba_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &usba_udc_data.pdata,
+	},
+	.resource	= usba_udc_resources,
+	.num_resources	= ARRAY_SIZE(usba_udc_resources),
+};
+
+void __init at91_add_device_usba(struct usba_platform_data *data)
+{
+	/*
+	 * Invalid pins are 0 on AT91, but the usba driver is shared
+	 * with AVR32, which use negative values instead. Once/if
+	 * gpio_is_valid() is ported to AT91, revisit this code.
+	 */
+	usba_udc_data.pdata.vbus_pin = -EINVAL;
+	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
+	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));;
+
+	if (data && data->vbus_pin > 0) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
+	}
+
+	/* Pullup pin is handled internally by USB device peripheral */
+
+	/* Clocks */
+	at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
+	at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
+
+	platform_device_register(&at91_usba_udc_device);
+}
+#else
+void __init at91_add_device_usba(struct usba_platform_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
  *  MMC / SD
  * -------------------------------------------------------------------- */