[ARM] 5289/1: [AT91] Convert boards to use sam9_smc_configure()

Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.

The following boards have been modified:
 cam60 : NAND
 cap9adk : NAND, NOR
 qil-a9260 : NAND
 sam9-l9260 : NAND
 sam9260ek : NAND
 sam9261ek : DM9000 Ethernet, NAND
 sam9263 : NAND
 sam9g20ek : NAND
 sam9rlek : NAND
 usb-a9260 : NAND
 usb-a9263 .: NAND

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 65 insertions, 15 deletions

diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 4977409d4fc6..d5266da55311 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -47,7 +47,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -76,7 +78,7 @@ static void __init ek_init_irq(void)
  * DM9000 ethernet device
  */
 #if defined(CONFIG_DM9000)
-static struct resource at91sam9261_dm9000_resource[] = {
+static struct resource dm9000_resource[] = {
 	[0] = {
 		.start	= AT91_CHIPSELECT_2,
 		.end	= AT91_CHIPSELECT_2 + 3,
@@ -98,27 +100,42 @@ static struct dm9000_plat_data dm9000_platdata = {
 	.flags		= DM9000_PLATF_16BITONLY,
 };
 
-static struct platform_device at91sam9261_dm9000_device = {
+static struct platform_device dm9000_device = {
 	.name		= "dm9000",
 	.id		= 0,
-	.num_resources	= ARRAY_SIZE(at91sam9261_dm9000_resource),
-	.resource	= at91sam9261_dm9000_resource,
+	.num_resources	= ARRAY_SIZE(dm9000_resource),
+	.resource	= dm9000_resource,
 	.dev		= {
 		.platform_data	= &dm9000_platdata,
 	}
 };
 
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 8,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 8,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 16,
+	.write_cycle		= 16,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+	.tdf_cycles		= 1,
+};
+
 static void __init ek_add_device_dm9000(void)
 {
-	/*
-	 * Configure Chip-Select 2 on SMC for the DM9000.
-	 * Note: These timings were calculated for MASTER_CLOCK = 100000000
-	 *  according to the DM9000 timings.
-	 */
-	at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-	at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
-	at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-	at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+	/* Configure chip-select 2 (DM9000) */
+	sam9_smc_configure(2, &dm9000_smc_config);
 
 	/* Configure Reset signal as output */
 	at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -126,7 +143,7 @@ static void __init ek_add_device_dm9000(void)
 	/* Configure Interrupt pin as input, no pull-up */
 	at91_set_gpio_input(AT91_PIN_PC11, 0);
 
-	platform_device_register(&at91sam9261_dm9000_device);
+	platform_device_register(&dm9000_device);
 }
 #else
 static void __init ek_add_device_dm9000(void) {}
@@ -197,6 +214,39 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* setup bus-width (8 or 16) */
+	if (ek_nand_data.bus_width_16)
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+	else
+		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * ADS7846 Touchscreen
  */
@@ -525,7 +575,7 @@ static void __init ek_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* DM9000 ethernet */
 	ek_add_device_dm9000();