ARM: at91: remove at91sam9g45/9m10 legacy board support

Remove legacy support for at91sam9g45/9m10 boards.
This include board files removal plus all legacy code for non DT boards
support (i.e. at91sam9g45.c and at91sam9g45_devices.c).
Use the Device Tree for running this board with newer kernels.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: Add sentence about DT, removed defconfig]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

1 files changed, 0 insertions, 527 deletions

diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
deleted file mode 100644
index a517c7f7af92..000000000000
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ /dev/null
@@ -1,527 +0,0 @@
-/*
- *  Board-specific setup code for the AT91SAM9M10G45 Evaluation Kit family
- *
- *  Covers: * AT91SAM9G45-EKES  board
- *          * AT91SAM9M10G45-EK board
- *
- *  Copyright (C) 2009 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/leds.h>
-#include <linux/atmel-mci.h>
-#include <linux/delay.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-
-#include <linux/platform_data/at91_adc.h>
-
-#include <mach/hardware.h>
-#include <video/atmel_lcdc.h>
-#include <media/soc_camera.h>
-#include <media/atmel-isi.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 12.000 MHz crystal */
-	at91_initialize(12000000);
-}
-
-/*
- * USB HS Host port (common to OHCI & EHCI)
- */
-static struct at91_usbh_data __initdata ek_usbh_hs_data = {
-	.ports		= 2,
-	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
-	.vbus_pin_active_low = {1, 1},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * USB HS Device port
- */
-static struct usba_platform_data __initdata ek_usba_udc_data = {
-	.vbus_pin	= AT91_PIN_PB19,
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PD10,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-static struct mci_platform_data __initdata mci1_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PD11,
-		.wp_pin		= AT91_PIN_PD29,
-	},
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PD5,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_64M,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-/* det_pin is not connected */
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC8,
-	.enable_pin	= AT91_PIN_PC14,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 3,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- *  ISI
- */
-static struct isi_platform_data __initdata isi_data = {
-	.frate			= ISI_CFG1_FRATE_CAPTURE_ALL,
-	/* to use codec and preview path simultaneously */
-	.full_mode		= 1,
-	.data_width_flags	= ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10,
-	/* ISI_MCK is provided by programmable clock or external clock */
-	.mck_hz			= 25000000,
-};
-
-
-/*
- * soc-camera OV2640
- */
-#if defined(CONFIG_SOC_CAMERA_OV2640) || \
-	defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
-static unsigned long isi_camera_query_bus_param(struct soc_camera_link *link)
-{
-	/* ISI board for ek using default 8-bits connection */
-	return SOCAM_DATAWIDTH_8;
-}
-
-static int i2c_camera_power(struct device *dev, int on)
-{
-	/* enable or disable the camera */
-	pr_debug("%s: %s the camera\n", __func__, on ? "ENABLE" : "DISABLE");
-	at91_set_gpio_output(AT91_PIN_PD13, !on);
-
-	if (!on)
-		goto out;
-
-	/* If enabled, give a reset impulse */
-	at91_set_gpio_output(AT91_PIN_PD12, 0);
-	msleep(20);
-	at91_set_gpio_output(AT91_PIN_PD12, 1);
-	msleep(100);
-
-out:
-	return 0;
-}
-
-static struct i2c_board_info i2c_camera = {
-	I2C_BOARD_INFO("ov2640", 0x30),
-};
-
-static struct soc_camera_link iclink_ov2640 = {
-	.bus_id			= 0,
-	.board_info		= &i2c_camera,
-	.i2c_adapter_id		= 0,
-	.power			= i2c_camera_power,
-	.query_bus_param	= isi_camera_query_bus_param,
-};
-
-static struct platform_device isi_ov2640 = {
-	.name	= "soc-camera-pdrv",
-	.id	= 0,
-	.dev	= {
-		.platform_data = &iclink_ov2640,
-	},
-};
-#endif
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-		.name           = "LG",
-		.refresh	= 60,
-		.xres		= 480,		.yres		= 272,
-		.pixclock	= KHZ2PICOS(9000),
-
-		.left_margin	= 1,		.right_margin	= 1,
-		.upper_margin	= 40,		.lower_margin	= 1,
-		.hsync_len	= 45,		.vsync_len	= 1,
-
-		.sync		= 0,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
-	.manufacturer	= "LG",
-	.monitor        = "LB043WQ1",
-
-	.modedb		= at91_tft_vga_modes,
-	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
-	.hfmin		= 15000,
-	.hfmax		= 17640,
-	.vfmin		= 57,
-	.vfmax		= 67,
-};
-
-#define AT91SAM9G45_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_TFT \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-/* Driver datas */
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
-	.lcdcon_is_backlight		= true,
-	.default_bpp			= 32,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9G45_DEFAULT_LCDCON2,
-	.default_monspecs		= &at91fb_default_monspecs,
-	.guard_time			= 9,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
-};
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * ADCs and touchscreen
- */
-static struct at91_adc_data ek_adc_data = {
-	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7),
-	.use_external_triggers = true,
-	.vref = 3300,
-	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
-};
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{	/* BP1, "leftclic" */
-		.code		= BTN_LEFT,
-		.gpio		= AT91_PIN_PB6,
-		.active_low	= 1,
-		.desc		= "left_click",
-		.wakeup		= 1,
-	},
-	{	/* BP2, "rightclic" */
-		.code		= BTN_RIGHT,
-		.gpio		= AT91_PIN_PB7,
-		.active_low	= 1,
-		.desc		= "right_click",
-		.wakeup		= 1,
-	},
-		/* BP3, "joystick" */
-	{
-		.code		= KEY_LEFT,
-		.gpio		= AT91_PIN_PB14,
-		.active_low	= 1,
-		.desc		= "Joystick Left",
-	},
-	{
-		.code		= KEY_RIGHT,
-		.gpio		= AT91_PIN_PB15,
-		.active_low	= 1,
-		.desc		= "Joystick Right",
-	},
-	{
-		.code		= KEY_UP,
-		.gpio		= AT91_PIN_PB16,
-		.active_low	= 1,
-		.desc		= "Joystick Up",
-	},
-	{
-		.code		= KEY_DOWN,
-		.gpio		= AT91_PIN_PB17,
-		.active_low	= 1,
-		.desc		= "Joystick Down",
-	},
-	{
-		.code		= KEY_ENTER,
-		.gpio		= AT91_PIN_PB18,
-		.active_low	= 1,
-		.desc		= "Joystick Press",
-	},
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(ek_buttons); i++) {
-		at91_set_GPIO_periph(ek_buttons[i].gpio, 1);
-		at91_set_deglitch(ek_buttons[i].gpio, 1);
-	}
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- * reset_pin is not connected: NRST
- */
-static struct ac97c_platform_data ek_ac97_data = {
-	.reset_pin	= -EINVAL,
-};
-
-
-/*
- * LEDs ... these could all be PWM-driven, for variable brightness
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "top" led, red, powerled */
-		.name			= "d8",
-		.gpio			= AT91_PIN_PD30,
-		.default_trigger	= "heartbeat",
-	},
-	{	/* "left" led, green, userled2, pwm3 */
-		.name			= "d6",
-		.gpio			= AT91_PIN_PD0,
-		.active_low		= 1,
-		.default_trigger	= "nand-disk",
-	},
-#if !IS_ENABLED(CONFIG_LEDS_PWM)
-	{	/* "right" led, green, userled1, pwm1 */
-		.name			= "d7",
-		.gpio			= AT91_PIN_PD31,
-		.active_low		= 1,
-		.default_trigger	= "mmc0",
-	},
-#endif
-};
-
-
-/*
- * PWM Leds
- */
-static struct pwm_lookup pwm_lookup[] = {
-	PWM_LOOKUP("at91sam9rl-pwm", 1, "leds_pwm", "d7",
-		   5000, PWM_POLARITY_INVERSED),
-};
-
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-static struct led_pwm pwm_leds[] = {
-	{	/* "right" led, green, userled1, pwm1 */
-		.name = "d7",
-		.max_brightness	= 255,
-	},
-};
-
-static struct led_pwm_platform_data pwm_data = {
-	.num_leds	= ARRAY_SIZE(pwm_leds),
-	.leds		= pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
-	.name	= "leds_pwm",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &pwm_data,
-	},
-};
-#endif
-
-static struct platform_device *devices[] __initdata = {
-#if defined(CONFIG_SOC_CAMERA_OV2640) || \
-	defined(CONFIG_SOC_CAMERA_OV2640_MODULE)
-	&isi_ov2640,
-#endif
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-	&leds_pwm,
-#endif
-};
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 not connected on the -EK board */
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB HS Host */
-	at91_add_device_usbh_ohci(&ek_usbh_hs_data);
-	at91_add_device_usbh_ehci(&ek_usbh_hs_data);
-	/* USB HS Device */
-	at91_add_device_usba(&ek_usba_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &mci0_data);
-	at91_add_device_mci(1, &mci1_data);
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* NAND */
-	ek_add_device_nand();
-	/* I2C */
-	at91_add_device_i2c(0, NULL, 0);
-	/* ISI, using programmable clock as ISI_MCK */
-	at91_add_device_isi(&isi_data, true);
-	/* LCD Controller */
-	at91_add_device_lcdc(&ek_lcdc_data);
-	/* ADC and touchscreen */
-	at91_add_device_adc(&ek_adc_data);
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* AC97 */
-	at91_add_device_ac97(&ek_ac97_data);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-	at91_add_device_pwm(1 << AT91_PWM1);
-#endif
-	/* Other platform devices */
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END