[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 0 insertions, 414 deletions

diff --git a/arch/arm/mach-at91rm9200/gpio.c b/arch/arm/mach-at91rm9200/gpio.c
deleted file mode 100644
index af22659c8a28..000000000000
--- a/arch/arm/mach-at91rm9200/gpio.c
+++ /dev/null
@@ -1,414 +0,0 @@
-/*
- * linux/arch/arm/mach-at91rm9200/gpio.c
- *
- * Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/clk.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/module.h>
-
-#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/at91_pio.h>
-#include <asm/arch/gpio.h>
-
-#include "generic.h"
-
-
-static struct at91_gpio_bank *gpio;
-static int gpio_banks;
-
-
-static inline void __iomem *pin_to_controller(unsigned pin)
-{
-	void __iomem *sys_base = (void __iomem *) AT91_VA_BASE_SYS;
-
-	pin -= PIN_BASE;
-	pin /= 32;
-	if (likely(pin < gpio_banks))
-		return sys_base + gpio[pin].offset;
-
-	return NULL;
-}
-
-static inline unsigned pin_to_mask(unsigned pin)
-{
-	pin -= PIN_BASE;
-	return 1 << (pin % 32);
-}
-
-
-/*--------------------------------------------------------------------------*/
-
-/* Not all hardware capabilities are exposed through these calls; they
- * only encapsulate the most common features and modes.  (So if you
- * want to change signals in groups, do it directly.)
- *
- * Bootloaders will usually handle some of the pin multiplexing setup.
- * The intent is certainly that by the time Linux is fully booted, all
- * pins should have been fully initialized.  These setup calls should
- * only be used by board setup routines, or possibly in driver probe().
- *
- * For bootloaders doing all that setup, these calls could be inlined
- * as NOPs so Linux won't duplicate any setup code
- */
-
-
-/*
- * mux the pin to the "A" internal peripheral role.
- */
-int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(mask, pio + PIO_ASR);
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_A_periph);
-
-
-/*
- * mux the pin to the "B" internal peripheral role.
- */
-int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(mask, pio + PIO_BSR);
-	__raw_writel(mask, pio + PIO_PDR);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_B_periph);
-
-
-/*
- * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and
- * configure it for an input.
- */
-int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
-	__raw_writel(mask, pio + PIO_ODR);
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_input);
-
-
-/*
- * mux the pin to the gpio controller (instead of "A" or "B" peripheral),
- * and configure it for an output.
- */
-int __init_or_module at91_set_gpio_output(unsigned pin, int value)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + PIO_IDR);
-	__raw_writel(mask, pio + PIO_PUDR);
-	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
-	__raw_writel(mask, pio + PIO_OER);
-	__raw_writel(mask, pio + PIO_PER);
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_output);
-
-
-/*
- * enable/disable the glitch filter; mostly used with IRQ handling.
- */
-int __init_or_module at91_set_deglitch(unsigned pin, int is_on)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-	__raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_deglitch);
-
-/*
- * enable/disable the multi-driver; This is only valid for output and
- * allows the output pin to run as an open collector output.
- */
-int __init_or_module at91_set_multi_drive(unsigned pin, int is_on)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-
-	__raw_writel(mask, pio + (is_on ? PIO_MDER : PIO_MDDR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_multi_drive);
-
-/*--------------------------------------------------------------------------*/
-
-/*
- * assuming the pin is muxed as a gpio output, set its value.
- */
-int at91_set_gpio_value(unsigned pin, int value)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (!pio)
-		return -EINVAL;
-	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
-	return 0;
-}
-EXPORT_SYMBOL(at91_set_gpio_value);
-
-
-/*
- * read the pin's value (works even if it's not muxed as a gpio).
- */
-int at91_get_gpio_value(unsigned pin)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-	u32		pdsr;
-
-	if (!pio)
-		return -EINVAL;
-	pdsr = __raw_readl(pio + PIO_PDSR);
-	return (pdsr & mask) != 0;
-}
-EXPORT_SYMBOL(at91_get_gpio_value);
-
-/*--------------------------------------------------------------------------*/
-
-#ifdef CONFIG_PM
-
-static u32 wakeups[MAX_GPIO_BANKS];
-static u32 backups[MAX_GPIO_BANKS];
-
-static int gpio_irq_set_wake(unsigned pin, unsigned state)
-{
-	unsigned	mask = pin_to_mask(pin);
-	unsigned	bank = (pin - PIN_BASE) / 32;
-
-	if (unlikely(bank >= MAX_GPIO_BANKS))
-		return -EINVAL;
-
-	if (state)
-		wakeups[bank] |= mask;
-	else
-		wakeups[bank] &= ~mask;
-
-	set_irq_wake(gpio[bank].id, state);
-
-	return 0;
-}
-
-void at91_gpio_suspend(void)
-{
-	int i;
-
-	for (i = 0; i < gpio_banks; i++) {
-		u32 pio = gpio[i].offset;
-
-		backups[i] = at91_sys_read(pio + PIO_IMR);
-		at91_sys_write(pio + PIO_IDR, backups[i]);
-		at91_sys_write(pio + PIO_IER, wakeups[i]);
-
-		if (!wakeups[i])
-			clk_disable(gpio[i].clock);
-		else {
-#ifdef CONFIG_PM_DEBUG
-			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
-#endif
-		}
-	}
-}
-
-void at91_gpio_resume(void)
-{
-	int i;
-
-	for (i = 0; i < gpio_banks; i++) {
-		u32 pio = gpio[i].offset;
-
-		if (!wakeups[i])
-			clk_enable(gpio[i].clock);
-
-		at91_sys_write(pio + PIO_IDR, wakeups[i]);
-		at91_sys_write(pio + PIO_IER, backups[i]);
-	}
-}
-
-#else
-#define gpio_irq_set_wake	NULL
-#endif
-
-
-/* Several AIC controller irqs are dispatched through this GPIO handler.
- * To use any AT91_PIN_* as an externally triggered IRQ, first call
- * at91_set_gpio_input() then maybe enable its glitch filter.
- * Then just request_irq() with the pin ID; it works like any ARM IRQ
- * handler, though it always triggers on rising and falling edges.
- *
- * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after
- * configuring them with at91_set_a_periph() or at91_set_b_periph().
- * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering.
- */
-
-static void gpio_irq_mask(unsigned pin)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (pio)
-		__raw_writel(mask, pio + PIO_IDR);
-}
-
-static void gpio_irq_unmask(unsigned pin)
-{
-	void __iomem	*pio = pin_to_controller(pin);
-	unsigned	mask = pin_to_mask(pin);
-
-	if (pio)
-		__raw_writel(mask, pio + PIO_IER);
-}
-
-static int gpio_irq_type(unsigned pin, unsigned type)
-{
-	return (type == IRQT_BOTHEDGE) ? 0 : -EINVAL;
-}
-
-static struct irq_chip gpio_irqchip = {
-	.name		= "GPIO",
-	.mask		= gpio_irq_mask,
-	.unmask		= gpio_irq_unmask,
-	.set_type	= gpio_irq_type,
-	.set_wake	= gpio_irq_set_wake,
-};
-
-static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
-{
-	unsigned	pin;
-	struct irq_desc	*gpio;
-	void __iomem	*pio;
-	u32		isr;
-
-	pio = get_irq_chip_data(irq);
-
-	/* temporarily mask (level sensitive) parent IRQ */
-	desc->chip->ack(irq);
-	for (;;) {
-		/* reading ISR acks the pending (edge triggered) GPIO interrupt */
-		isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR);
-		if (!isr)
-			break;
-
-		pin = (unsigned) get_irq_data(irq);
-		gpio = &irq_desc[pin];
-
-		while (isr) {
-			if (isr & 1) {
-				if (unlikely(gpio->depth)) {
-					/*
-					 * The core ARM interrupt handler lazily disables IRQs so
-					 * another IRQ must be generated before it actually gets
-					 * here to be disabled on the GPIO controller.
-					 */
-					gpio_irq_mask(pin);
-				}
-				else
-					desc_handle_irq(pin, gpio);
-			}
-			pin++;
-			gpio++;
-			isr >>= 1;
-		}
-	}
-	desc->chip->unmask(irq);
-	/* now it may re-trigger */
-}
-
-/*--------------------------------------------------------------------------*/
-
-/*
- * Called from the processor-specific init to enable GPIO interrupt support.
- */
-void __init at91_gpio_irq_setup(void)
-{
-	unsigned	pioc, pin;
-
-	for (pioc = 0, pin = PIN_BASE;
-			pioc < gpio_banks;
-			pioc++) {
-		void __iomem	*controller;
-		unsigned	id = gpio[pioc].id;
-		unsigned	i;
-
-		clk_enable(gpio[pioc].clock);	/* enable PIO controller's clock */
-
-		controller = (void __iomem *) AT91_VA_BASE_SYS + gpio[pioc].offset;
-		__raw_writel(~0, controller + PIO_IDR);
-
-		set_irq_data(id, (void *) pin);
-		set_irq_chip_data(id, controller);
-
-		for (i = 0; i < 32; i++, pin++) {
-			/*
-			 * Can use the "simple" and not "edge" handler since it's
-			 * shorter, and the AIC handles interupts sanely.
-			 */
-			set_irq_chip(pin, &gpio_irqchip);
-			set_irq_handler(pin, handle_simple_irq);
-			set_irq_flags(pin, IRQF_VALID);
-		}
-
-		set_irq_chained_handler(id, gpio_irq_handler);
-	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
-}
-
-/*
- * Called from the processor-specific init to enable GPIO pin support.
- */
-void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
-{
-	BUG_ON(nr_banks > MAX_GPIO_BANKS);
-
-	gpio = data;
-	gpio_banks = nr_banks;
-}