kirkwood: Add iconnect support

Add support for Iomega Iconnect system.

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

1 files changed, 165 insertions, 0 deletions

diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
new file mode 100644
index 000000000000..2222c5739519
--- /dev/null
+++ b/arch/arm/mach-kirkwood/board-iconnect.c
@@ -0,0 +1,165 @@
+/*
+ * arch/arm/mach-kirkwood/board-iconnect.c
+ *
+ * Iomega i-connect Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mv643xx_eth_platform_data iconnect_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(11),
+};
+
+static struct gpio_led iconnect_led_pins[] = {
+	{
+		.name		= "led_level",
+		.gpio		= 41,
+		.default_trigger = "default-on",
+	}, {
+		.name		= "power:blue",
+		.gpio		= 42,
+		.default_trigger = "timer",
+	}, {
+		.name		= "power:red",
+		.gpio		= 43,
+	}, {
+		.name		= "usb1:blue",
+		.gpio		= 44,
+	}, {
+		.name		= "usb2:blue",
+		.gpio		= 45,
+	}, {
+		.name		= "usb3:blue",
+		.gpio		= 46,
+	}, {
+		.name		= "usb4:blue",
+		.gpio		= 47,
+	}, {
+		.name		= "otb:blue",
+		.gpio		= 48,
+	},
+};
+
+static struct gpio_led_platform_data iconnect_led_data = {
+	.leds		= iconnect_led_pins,
+	.num_leds	= ARRAY_SIZE(iconnect_led_pins),
+	.gpio_blink_set	= orion_gpio_led_blink_set,
+};
+
+static struct platform_device iconnect_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &iconnect_led_data,
+	}
+};
+
+static unsigned int iconnect_mpp_config[] __initdata = {
+	MPP12_GPIO,
+	MPP35_GPIO,
+	MPP41_GPIO,
+	MPP42_GPIO,
+	MPP43_GPIO,
+	MPP44_GPIO,
+	MPP45_GPIO,
+	MPP46_GPIO,
+	MPP47_GPIO,
+	MPP48_GPIO,
+	0
+};
+
+static struct i2c_board_info __initdata iconnect_board_info[] = {
+	{
+		I2C_BOARD_INFO("lm63", 0x4c),
+	},
+};
+
+static struct mtd_partition iconnect_nand_parts[] = {
+	{
+		.name = "flash",
+		.offset = 0,
+		.size = MTDPART_SIZ_FULL,
+	},
+};
+
+/* yikes... theses are the original input buttons */
+/* but I'm not convinced by the sw event choices  */
+static struct gpio_keys_button iconnect_buttons[] = {
+	{
+		.type		= EV_SW,
+		.code		= SW_LID,
+		.gpio		= 12,
+		.desc		= "Reset Button",
+		.active_low	= 1,
+		.debounce_interval = 100,
+	}, {
+		.type		= EV_SW,
+		.code		= SW_TABLET_MODE,
+		.gpio		= 35,
+		.desc		= "OTB Button",
+		.active_low	= 1,
+		.debounce_interval = 100,
+	},
+};
+
+static struct gpio_keys_platform_data iconnect_button_data = {
+	.buttons	= iconnect_buttons,
+	.nbuttons	= ARRAY_SIZE(iconnect_buttons),
+};
+
+static struct platform_device iconnect_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev        = {
+		.platform_data  = &iconnect_button_data,
+	},
+};
+
+void __init iconnect_init(void)
+{
+	kirkwood_mpp_conf(iconnect_mpp_config);
+	kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
+	kirkwood_i2c_init();
+	i2c_register_board_info(0, iconnect_board_info,
+		ARRAY_SIZE(iconnect_board_info));
+
+	kirkwood_ehci_init();
+	kirkwood_ge00_init(&iconnect_ge00_data);
+
+	platform_device_register(&iconnect_button_device);
+	platform_device_register(&iconnect_leds);
+}
+
+static int __init iconnect_pci_init(void)
+{
+	if (of_machine_is_compatible("iom,iconnect"))
+		kirkwood_pcie_init(KW_PCIE0);
+	return 0;
+}
+subsys_initcall(iconnect_pci_init);