ARM: OMAP1: Use generic map_io, init_early and init_irq

This allows removing omap hacks for map_io allowing generic
map_io.

Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.

Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 36 insertions, 40 deletions

diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index a6b1bea50371..b09dfe6d6e8d 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -297,6 +297,39 @@ static struct omap_board_config_kernel fsample_config[] __initdata = {
 
 static void __init omap_fsample_init(void)
 {
+	/* Early, board-dependent init */
+
+	/*
+	 * Hold GSM Reset until needed
+	 */
+	omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
+
+	/*
+	 * UARTs -> done automagically by 8250 driver
+	 */
+
+	/*
+	 * CSx timings, GPIO Mux ... setup
+	 */
+
+	/* Flash: CS0 timings setup */
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
+	omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
+
+	/*
+	 * Ethernet support through the debug board
+	 * CS1 timings setup
+	 */
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
+	omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
+
+	/*
+	 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
+	 * It is used as the Ethernet controller interrupt
+	 */
+	omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
+			OMAP7XX_IO_CONF_9);
+
 	fsample_init_smc91x();
 
 	if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
@@ -326,12 +359,6 @@ static void __init omap_fsample_init(void)
 	omap_register_i2c_bus(1, 100, NULL, 0);
 }
 
-static void __init omap_fsample_init_irq(void)
-{
-	omap1_init_common_hw();
-	omap1_init_irq();
-}
-
 /* Only FPGA needs to be mapped here. All others are done with ioremap */
 static struct map_desc omap_fsample_io_desc[] __initdata = {
 	{
@@ -350,49 +377,18 @@ static struct map_desc omap_fsample_io_desc[] __initdata = {
 
 static void __init omap_fsample_map_io(void)
 {
-	omap1_map_common_io();
+	omap15xx_map_io();
 	iotable_init(omap_fsample_io_desc,
 		     ARRAY_SIZE(omap_fsample_io_desc));
-
-	/* Early, board-dependent init */
-
-	/*
-	 * Hold GSM Reset until needed
-	 */
-	omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
-
-	/*
-	 * UARTs -> done automagically by 8250 driver
-	 */
-
-	/*
-	 * CSx timings, GPIO Mux ... setup
-	 */
-
-	/* Flash: CS0 timings setup */
-	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
-	omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
-
-	/*
-	 * Ethernet support through the debug board
-	 * CS1 timings setup
-	 */
-	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
-	omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
-
-	/*
-	 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
-	 * It is used as the Ethernet controller interrupt
-	 */
-	omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
 }
 
 MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
 /* Maintainer: Brian Swetland <swetland@google.com> */
 	.boot_params	= 0x10000100,
 	.map_io		= omap_fsample_map_io,
+	.init_early	= omap1_init_early,
 	.reserve	= omap_reserve,
-	.init_irq	= omap_fsample_init_irq,
+	.init_irq	= omap1_init_irq,
 	.init_machine	= omap_fsample_init,
 	.timer		= &omap1_timer,
 MACHINE_END