Merge tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

From Tony Lindgren <tony@atomide.com>

Here is some more omap clean-up. The biggest changes are
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.

* tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: hwmod: remove prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain
  ARM: OMAP3: Move McBSP fck clock alias to hwmod data
  ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2430
  ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2420
  ARM: OMAP: dsp: interface to control module functions
  ARM: OMAP2+: control: new APIs to configure boot address and mode
  ARM: OMAP2+: CLEANUP: Remove ARCH_OMAPx ifdef from struct dpll_data
  ARM: OMAP2+: hwmod: use init-time function pointer for _init_clkdm
  ARM: OMAP2+: hwmod: use init-time function pointer for hardreset
  ARM: OMAP2+: hwmod: use init-time function pointer for wait_target_ready
  ARM: OMAP4: hwmod: drop extra cpu_is check from _wait_target_disable()
  ARM: OMAP2+: hwmod: use init-time function ptrs for enable/disable module
  ARM: OMAP4: hwmod: rename _enable_module to _omap4_enable_module()
  ARM: OMAP: Make FS USB omap1 only
  ARM: OMAP2: Remove legacy USB FS support
  ARM: OMAP3: There is no FS USB controller on omap3
  ARM: OMAP: dma: Clear status registers on enable/disable irq

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

1 files changed, 0 insertions, 18 deletions

diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 502c31e123be..519bcd3079e8 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -35,7 +35,6 @@
 #include <asm/mach/flash.h>
 
 #include <plat/led.h>
-#include <plat/usb.h>
 #include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
@@ -253,13 +252,6 @@ out:
 	clk_put(gpmc_fck);
 }
 
-static struct omap_usb_config apollon_usb_config __initdata = {
-	.register_dev	= 1,
-	.hmc_mode	= 0x14,	/* 0:dev 1:host1 2:disable */
-
-	.pins[0]	= 6,
-};
-
 static struct panel_generic_dpi_data apollon_panel_data = {
 	.name			= "apollon",
 };
@@ -297,15 +289,6 @@ static void __init apollon_led_init(void)
 	gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
 }
 
-static void __init apollon_usb_init(void)
-{
-	/* USB device */
-	/* DEVICE_SUSPEND */
-	omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
-	gpio_request_one(12, GPIOF_OUT_INIT_LOW, "USB suspend");
-	omap2_usbfs_init(&apollon_usb_config);
-}
-
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -321,7 +304,6 @@ static void __init omap_apollon_init(void)
 	apollon_init_smc91x();
 	apollon_led_init();
 	apollon_flash_init();
-	apollon_usb_init();
 
 	/* REVISIT: where's the correct place */
 	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);