ARM: OMAP2: Powerdomain: Add base OMAP2/3 powerdomain code

This patch creates an interface to the powerdomain registers in the
PRM/CM modules on OMAP2/3.  This interface is intended to be used by
PM code, e.g., pm.c; not by device drivers directly.

Each powerdomain will be defined in later patches as static
structures.  Also defined are dependencies between powerdomains,
used for adding and removing PM_WKDEP and CM_SLEEPDEP bits.  The
powerdomain structures are linked into a list at boot by
pwrdm_register(), similar to the OMAP clock code.

The patch adds a Kconfig option, CONFIG_OMAP_DEBUG_POWERDOMAIN, which
when enabled will emit verbose debug messages via pr_debug().

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 17 insertions, 10 deletions

diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index 3ff74952f835..dff7a72fefc9 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -62,11 +62,14 @@ static void omap3_dpll_recalc(struct clk *clk)
 static void _omap3_dpll_write_clken(struct clk *clk, u8 clken_bits)
 {
 	const struct dpll_data *dd;
+	u32 v;
 
 	dd = clk->dpll_data;
 
-	cm_rmw_reg_bits(dd->enable_mask, clken_bits << __ffs(dd->enable_mask),
-			dd->control_reg);
+	v = __raw_readl(dd->control_reg);
+	v &= ~dd->enable_mask;
+	v |= clken_bits << __ffs(dd->enable_mask);
+	__raw_writel(v, dd->control_reg);
 }
 
 /* _omap3_wait_dpll_status: wait for a DPLL to enter a specific state */
@@ -82,7 +85,7 @@ static int _omap3_wait_dpll_status(struct clk *clk, u8 state)
 	state <<= dd->idlest_bit;
 	idlest_mask = 1 << dd->idlest_bit;
 
-	while (((cm_read_reg(dd->idlest_reg) & idlest_mask) != state) &&
+	while (((__raw_readl(dd->idlest_reg) & idlest_mask) != state) &&
 	       i < MAX_DPLL_WAIT_TRIES) {
 		i++;
 		udelay(1);
@@ -285,7 +288,7 @@ static u32 omap3_dpll_autoidle_read(struct clk *clk)
 
 	dd = clk->dpll_data;
 
-	v = cm_read_reg(dd->autoidle_reg);
+	v = __raw_readl(dd->autoidle_reg);
 	v &= dd->autoidle_mask;
 	v >>= __ffs(dd->autoidle_mask);
 
@@ -304,6 +307,7 @@ static u32 omap3_dpll_autoidle_read(struct clk *clk)
 static void omap3_dpll_allow_idle(struct clk *clk)
 {
 	const struct dpll_data *dd;
+	u32 v;
 
 	if (!clk || !clk->dpll_data)
 		return;
@@ -315,9 +319,10 @@ static void omap3_dpll_allow_idle(struct clk *clk)
 	 * by writing 0x5 instead of 0x1.  Add some mechanism to
 	 * optionally enter this mode.
 	 */
-	cm_rmw_reg_bits(dd->autoidle_mask,
-			DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask),
-			dd->autoidle_reg);
+	v = __raw_readl(dd->autoidle_reg);
+	v &= ~dd->autoidle_mask;
+	v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask);
+	__raw_writel(v, dd->autoidle_reg);
 }
 
 /**
@@ -329,15 +334,17 @@ static void omap3_dpll_allow_idle(struct clk *clk)
 static void omap3_dpll_deny_idle(struct clk *clk)
 {
 	const struct dpll_data *dd;
+	u32 v;
 
 	if (!clk || !clk->dpll_data)
 		return;
 
 	dd = clk->dpll_data;
 
-	cm_rmw_reg_bits(dd->autoidle_mask,
-			DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask),
-			dd->autoidle_reg);
+	v = __raw_readl(dd->autoidle_reg);
+	v &= ~dd->autoidle_mask;
+	v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask);
+	__raw_writel(v, dd->autoidle_reg);
 }
 
 /* Clock control for DPLL outputs */