Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull part one of ARM SoC updates from Olof Johansson:
 "A quite large set of SoC updates this cycle.  In no particular order:

   - Multi-cluster power management for Samsung Exynos, adding support
     for big.LITTLE CPU switching on EXYNOS5

   - SMP support for Marvell Armada 375 and 38x

   - SMP rework on Allwinner A31

   - Xilinx Zynq support for SOC_BUS, big endian

   - Marvell orion5x platform cleanup, modernizing the implementation
     and moving to DT.

   - _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
     that their platform can be enabled in the same kernel binary as
     most of the other v7 platforms in the tree.  \o/

     The work isn't quite complete, there's some driver fixes still
     needed, but the basics now work.

  New SoC support added:

   - Freescale i.MX6SX

   - LSI Axxia AXM55xx SoCs

   - Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800

   - STi STIH407

  plus a large set of various smaller updates for different platforms.
  I'm probably missing some important one here"

* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
  ARM: exynos: don't run exynos4 l2x0 setup on other platforms
  ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
  ARM: EXYNOS: mcpm rename the power_down_finish
  ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
  ARM: EXYNOS: Enable multi-platform build support
  ARM: EXYNOS: Consolidate Kconfig entries
  ARM: EXYNOS: Add support for EXYNOS5410 SoC
  ARM: EXYNOS: Support secondary CPU boot of Exynos3250
  ARM: EXYNOS: Add Exynos3250 SoC ID
  ARM: EXYNOS: Add 5800 SoC support
  ARM: EXYNOS: initial board support for exynos5260 SoC
  clk: exynos5410: register clocks using common clock framework
  ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
  ARM: sunxi: allow building without reset controller
  Documentation: devicetree: arm: sort enable-method entries
  ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
  clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
  ARM: dts: axxia: Add reset controller
  power: reset: Add Axxia system reset driver
  ARM: axxia: Adding defconfig for AXM55xx
  ...

1 files changed, 0 insertions, 60 deletions

diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c
index 615e5b1fb025..6bf626700557 100644
--- a/arch/arm/mach-omap2/omap_twl.c
+++ b/arch/arm/mach-omap2/omap_twl.c
@@ -46,15 +46,8 @@
 
 static bool is_offset_valid;
 static u8 smps_offset;
-/*
- * Flag to ensure Smartreflex bit in TWL
- * being cleared in board file is not overwritten.
- */
-static bool __initdata twl_sr_enable_autoinit;
 
-#define TWL4030_DCDC_GLOBAL_CFG        0x06
 #define REG_SMPS_OFFSET         0xE0
-#define SMARTREFLEX_ENABLE     BIT(3)
 
 static unsigned long twl4030_vsel_to_uv(const u8 vsel)
 {
@@ -251,18 +244,6 @@ int __init omap3_twl_init(void)
 	if (!cpu_is_omap34xx())
 		return -ENODEV;
 
-	/*
-	 * The smartreflex bit on twl4030 specifies if the setting of voltage
-	 * is done over the I2C_SR path. Since this setting is independent of
-	 * the actual usage of smartreflex AVS module, we enable TWL SR bit
-	 * by default irrespective of whether smartreflex AVS module is enabled
-	 * on the OMAP side or not. This is because without this bit enabled,
-	 * the voltage scaling through vp forceupdate/bypass mechanism of
-	 * voltage scaling will not function on TWL over I2C_SR.
-	 */
-	if (!twl_sr_enable_autoinit)
-		omap3_twl_set_sr_bit(true);
-
 	voltdm = voltdm_lookup("mpu_iva");
 	omap_voltage_register_pmic(voltdm, &omap3_mpu_pmic);
 
@@ -271,44 +252,3 @@ int __init omap3_twl_init(void)
 
 	return 0;
 }
-
-/**
- * omap3_twl_set_sr_bit() - Set/Clear SR bit on TWL
- * @enable: enable SR mode in twl or not
- *
- * If 'enable' is true, enables Smartreflex bit on TWL 4030 to make sure
- * voltage scaling through OMAP SR works. Else, the smartreflex bit
- * on twl4030 is cleared as there are platforms which use OMAP3 and T2 but
- * use Synchronized Scaling Hardware Strategy (ENABLE_VMODE=1) and Direct
- * Strategy Software Scaling Mode (ENABLE_VMODE=0), for setting the voltages,
- * in those scenarios this bit is to be cleared (enable = false).
- *
- * Returns 0 on success, error is returned if I2C read/write fails.
- */
-int __init omap3_twl_set_sr_bit(bool enable)
-{
-	u8 temp;
-	int ret;
-	if (twl_sr_enable_autoinit)
-		pr_warning("%s: unexpected multiple calls\n", __func__);
-
-	ret = twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &temp,
-			      TWL4030_DCDC_GLOBAL_CFG);
-	if (ret)
-		goto err;
-
-	if (enable)
-		temp |= SMARTREFLEX_ENABLE;
-	else
-		temp &= ~SMARTREFLEX_ENABLE;
-
-	ret = twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, temp,
-			       TWL4030_DCDC_GLOBAL_CFG);
-	if (!ret) {
-		twl_sr_enable_autoinit = true;
-		return 0;
-	}
-err:
-	pr_err("%s: Error access to TWL4030 (%d)\n", __func__, ret);
-	return ret;
-}