atmel-mci: Platform code for supporting multiple mmc slots

Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.

Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.

Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

6 files changed, 113 insertions, 30 deletions

diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index b8286f1ce854..f3085208959f 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -53,8 +53,11 @@ static struct spi_board_info spi0_board_info[] __initdata = {
 };
 
 static struct mci_platform_data __initdata mci0_data = {
-	.detect_pin	= GPIO_PIN_PC(25),
-	.wp_pin		= GPIO_PIN_PE(0),
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= GPIO_PIN_PC(25),
+		.wp_pin		= GPIO_PIN_PE(0),
+	},
 };
 
 /*
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index dfc3443e23aa..4fedbc4488de 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -264,16 +264,20 @@ void __init setup_board(void)
 
 #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
 
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+
 /* MMC card detect requires MACB0 *NOT* be used */
 #ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
-static struct mci_platform_data __initdata mci0_data = {
-	.detect_pin	= GPIO_PIN_PC(14),	/* gpio30/sdcd */
-	.wp_pin		= GPIO_PIN_PC(15),	/* gpio31/sdwp */
-};
-#define MCI_PDATA	&mci0_data
+		.detect_pin	= GPIO_PIN_PC(14), /* gpio30/sdcd */
+		.wp_pin		= GPIO_PIN_PC(15), /* gpio31/sdwp */
 #else
-#define MCI_PDATA	NULL
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
 #endif	/* SW6 for sd{cd,wp} routing */
+	},
+};
 
 #endif	/* SW2 for MMC signal routing */
 
@@ -326,7 +330,7 @@ static int __init atstk1002_init(void)
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
 #endif
 #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
-	at32_add_device_mci(0, MCI_PDATA);
+	at32_add_device_mci(0, &mci0_pdata);
 #endif
 #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
 	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c
index 0cf664174c17..acc61235b895 100644
--- a/arch/avr32/boards/atstk1000/atstk1003.c
+++ b/arch/avr32/boards/atstk1000/atstk1003.c
@@ -66,6 +66,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { {
 } };
 #endif
 
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+#endif
+
 #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
 static void __init atstk1003_setup_extdac(void)
 {
@@ -154,7 +164,7 @@ static int __init atstk1003_init(void)
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
 #endif
 #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
-	at32_add_device_mci(0, NULL);
+	at32_add_device_mci(0, &mci0_data);
 #endif
 	at32_add_device_usba(0, NULL);
 #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c
index 50a5273e5916..d6a2d02f0329 100644
--- a/arch/avr32/boards/atstk1000/atstk1004.c
+++ b/arch/avr32/boards/atstk1000/atstk1004.c
@@ -71,6 +71,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { {
 } };
 #endif
 
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+#endif
+
 #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
 static void __init atstk1004_setup_extdac(void)
 {
@@ -137,7 +147,7 @@ static int __init atstk1004_init(void)
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
 #endif
 #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
-	at32_add_device_mci(0, NULL);
+	at32_add_device_mci(0, &mci0_data);
 #endif
 	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
 			     fbmem_start, fbmem_size, 0);
diff --git a/arch/avr32/include/asm/atmel-mci.h b/arch/avr32/include/asm/atmel-mci.h
index c2ea6e1c9aa1..d38c64ca41e8 100644
--- a/arch/avr32/include/asm/atmel-mci.h
+++ b/arch/avr32/include/asm/atmel-mci.h
@@ -1,9 +1,29 @@
 #ifndef __ASM_AVR32_ATMEL_MCI_H
 #define __ASM_AVR32_ATMEL_MCI_H
 
-struct mci_platform_data {
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @detect_pin: GPIO pin wired to the card detect switch
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ */
+struct mci_slot_pdata {
+	unsigned int		bus_width;
 	int			detect_pin;
 	int			wp_pin;
 };
 
+/**
+ * struct mci_platform_data - board-specific MMC/SDcard configuration
+ * @slot: Per-slot configuration data.
+ */
+struct mci_platform_data {
+	struct mci_slot_pdata	slot[2];
+};
+
 #endif /* __ASM_AVR32_ATMEL_MCI_H */
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index e01dbe4ebb40..9967d5a3b6eb 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1272,10 +1272,13 @@ static struct clk atmel_mci0_pclk = {
 struct platform_device *__init
 at32_add_device_mci(unsigned int id, struct mci_platform_data *data)
 {
-	struct mci_platform_data	_data;
 	struct platform_device		*pdev;
 
-	if (id != 0)
+	if (id != 0 || !data)
+		return NULL;
+
+	/* Must have at least one usable slot */
+	if (!data->slot[0].bus_width && !data->slot[1].bus_width)
 		return NULL;
 
 	pdev = platform_device_alloc("atmel_mci", id);
@@ -1286,28 +1289,61 @@ at32_add_device_mci(unsigned int id, struct mci_platform_data *data)
 				ARRAY_SIZE(atmel_mci0_resource)))
 		goto fail;
 
-	if (!data) {
-		data = &_data;
-		memset(data, -1, sizeof(struct mci_platform_data));
-		data->detect_pin = GPIO_PIN_NONE;
-		data->wp_pin = GPIO_PIN_NONE;
-	}
 
 	if (platform_device_add_data(pdev, data,
 				sizeof(struct mci_platform_data)))
 		goto fail;
 
-	select_peripheral(PA(10), PERIPH_A, 0);	/* CLK	 */
-	select_peripheral(PA(11), PERIPH_A, 0);	/* CMD	 */
-	select_peripheral(PA(12), PERIPH_A, 0);	/* DATA0 */
-	select_peripheral(PA(13), PERIPH_A, 0);	/* DATA1 */
-	select_peripheral(PA(14), PERIPH_A, 0);	/* DATA2 */
-	select_peripheral(PA(15), PERIPH_A, 0);	/* DATA3 */
+	/* CLK line is common to both slots */
+	select_peripheral(PA(10), PERIPH_A, 0);
 
-	if (gpio_is_valid(data->detect_pin))
-		at32_select_gpio(data->detect_pin, 0);
-	if (gpio_is_valid(data->wp_pin))
-		at32_select_gpio(data->wp_pin, 0);
+	switch (data->slot[0].bus_width) {
+	case 4:
+		select_peripheral(PA(13), PERIPH_A, 0);	/* DATA1 */
+		select_peripheral(PA(14), PERIPH_A, 0);	/* DATA2 */
+		select_peripheral(PA(15), PERIPH_A, 0);	/* DATA3 */
+		/* fall through */
+	case 1:
+		select_peripheral(PA(11), PERIPH_A, 0);	/* CMD	 */
+		select_peripheral(PA(12), PERIPH_A, 0);	/* DATA0 */
+
+		if (gpio_is_valid(data->slot[0].detect_pin))
+			at32_select_gpio(data->slot[0].detect_pin, 0);
+		if (gpio_is_valid(data->slot[0].wp_pin))
+			at32_select_gpio(data->slot[0].wp_pin, 0);
+		break;
+	case 0:
+		/* Slot is unused */
+		break;
+	default:
+		goto fail;
+	}
+
+	switch (data->slot[1].bus_width) {
+	case 4:
+		select_peripheral(PB(8),  PERIPH_B, 0);	/* DATA1 */
+		select_peripheral(PB(9),  PERIPH_B, 0);	/* DATA2 */
+		select_peripheral(PB(10), PERIPH_B, 0);	/* DATA3 */
+		/* fall through */
+	case 1:
+		select_peripheral(PB(6),  PERIPH_B, 0); /* CMD	 */
+		select_peripheral(PB(7),  PERIPH_B, 0); /* DATA0 */
+
+		if (gpio_is_valid(data->slot[1].detect_pin))
+			at32_select_gpio(data->slot[1].detect_pin, 0);
+		if (gpio_is_valid(data->slot[1].wp_pin))
+			at32_select_gpio(data->slot[1].wp_pin, 0);
+		break;
+	case 0:
+		/* Slot is unused */
+		break;
+	default:
+		if (!data->slot[0].bus_width)
+			goto fail;
+
+		data->slot[1].bus_width = 0;
+		break;
+	}
 
 	atmel_mci0_pclk.dev = &pdev->dev;