CRIS: Remove legacy RTC drivers

These old drivers are not used anymore, we use the ones in drivers/rtc.
This allows us to remove some cruft in the CRIS timekeeping code.

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>

2 files changed, 0 insertions, 895 deletions

diff --git a/arch/cris/arch-v10/drivers/ds1302.c b/arch/cris/arch-v10/drivers/ds1302.c
deleted file mode 100644
index 74f99c688c8d..000000000000
--- a/arch/cris/arch-v10/drivers/ds1302.c
+++ /dev/null
@@ -1,515 +0,0 @@
-/*!***************************************************************************
-*!
-*! FILE NAME  : ds1302.c
-*!
-*! DESCRIPTION: Implements an interface for the DS1302 RTC through Etrax I/O
-*!
-*! Functions exported: ds1302_readreg, ds1302_writereg, ds1302_init
-*!
-*! ---------------------------------------------------------------------------
-*!
-*! (C) Copyright 1999-2007 Axis Communications AB, LUND, SWEDEN
-*!
-*!***************************************************************************/
-
-
-#include <linux/fs.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/miscdevice.h>
-#include <linux/delay.h>
-#include <linux/mutex.h>
-#include <linux/bcd.h>
-#include <linux/capability.h>
-
-#include <asm/uaccess.h>
-#include <arch/svinto.h>
-#include <asm/io.h>
-#include <asm/rtc.h>
-#include <arch/io_interface_mux.h>
-
-#include "i2c.h"
-
-#define RTC_MAJOR_NR 121 /* local major, change later */
-
-static DEFINE_MUTEX(ds1302_mutex);
-static const char ds1302_name[] = "ds1302";
-
-/* The DS1302 might be connected to different bits on different products. 
- * It has three signals - SDA, SCL and RST. RST and SCL are always outputs,
- * but SDA can have a selected direction.
- * For now, only PORT_PB is hardcoded.
- */
-
-/* The RST bit may be on either the Generic Port or Port PB. */
-#ifdef CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT
-#define TK_RST_OUT(x) REG_SHADOW_SET(R_PORT_G_DATA,  port_g_data_shadow,  CONFIG_ETRAX_DS1302_RSTBIT, x)
-#define TK_RST_DIR(x)
-#else
-#define TK_RST_OUT(x) REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, CONFIG_ETRAX_DS1302_RSTBIT, x)
-#define TK_RST_DIR(x) REG_SHADOW_SET(R_PORT_PB_DIR,  port_pb_dir_shadow,  CONFIG_ETRAX_DS1302_RSTBIT, x)
-#endif
-
-
-#define TK_SDA_OUT(x) REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, CONFIG_ETRAX_DS1302_SDABIT, x)
-#define TK_SCL_OUT(x) REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, CONFIG_ETRAX_DS1302_SCLBIT, x)
-
-#define TK_SDA_IN()   ((*R_PORT_PB_READ >> CONFIG_ETRAX_DS1302_SDABIT) & 1)
-/* 1 is out, 0 is in */
-#define TK_SDA_DIR(x) REG_SHADOW_SET(R_PORT_PB_DIR,  port_pb_dir_shadow,  CONFIG_ETRAX_DS1302_SDABIT, x)
-#define TK_SCL_DIR(x) REG_SHADOW_SET(R_PORT_PB_DIR,  port_pb_dir_shadow,  CONFIG_ETRAX_DS1302_SCLBIT, x)
-
-
-/*
- * The reason for tempudelay and not udelay is that loops_per_usec
- * (used in udelay) is not set when functions here are called from time.c 
- */
-
-static void tempudelay(int usecs) 
-{
-	volatile int loops;
-
-	for(loops = usecs * 12; loops > 0; loops--)
-		/* nothing */;	
-}
-
-
-/* Send 8 bits. */
-static void
-out_byte(unsigned char x) 
-{
-	int i;
-	TK_SDA_DIR(1);
-	for (i = 8; i--;) {
-		/* The chip latches incoming bits on the rising edge of SCL. */
-		TK_SCL_OUT(0);
-		TK_SDA_OUT(x & 1);
-		tempudelay(1);
-		TK_SCL_OUT(1);
-		tempudelay(1);
-		x >>= 1;
-	}
-	TK_SDA_DIR(0);
-}
-
-static unsigned char
-in_byte(void) 
-{
-	unsigned char x = 0;
-	int i;
-
-	/* Read byte. Bits come LSB first, on the falling edge of SCL.
-	 * Assume SDA is in input direction already.
-	 */
-	TK_SDA_DIR(0);
-
-	for (i = 8; i--;) {
-		TK_SCL_OUT(0);
-		tempudelay(1);
-		x >>= 1;
-		x |= (TK_SDA_IN() << 7);
-		TK_SCL_OUT(1);
-		tempudelay(1);
-	}
-
-	return x;
-}
-
-/* Prepares for a transaction by de-activating RST (active-low). */
-
-static void
-start(void) 
-{
-	TK_SCL_OUT(0);
-	tempudelay(1);
-	TK_RST_OUT(0);
-	tempudelay(5);
-	TK_RST_OUT(1);	
-}
-
-/* Ends a transaction by taking RST active again. */
-
-static void
-stop(void) 
-{
-	tempudelay(2);
-	TK_RST_OUT(0);
-}
-
-/* Enable writing. */
-
-static void
-ds1302_wenable(void) 
-{
-	start(); 	
-	out_byte(0x8e); /* Write control register  */
-	out_byte(0x00); /* Disable write protect bit 7 = 0 */
-	stop();
-}
-
-/* Disable writing. */
-
-static void
-ds1302_wdisable(void) 
-{
-	start();
-	out_byte(0x8e); /* Write control register  */
-	out_byte(0x80); /* Disable write protect bit 7 = 0 */
-	stop();
-}
-
-
-
-/* Read a byte from the selected register in the DS1302. */
-
-unsigned char
-ds1302_readreg(int reg) 
-{
-	unsigned char x;
-
-	start();
-	out_byte(0x81 | (reg << 1)); /* read register */
-	x = in_byte();
-	stop();
-
-	return x;
-}
-
-/* Write a byte to the selected register. */
-
-void
-ds1302_writereg(int reg, unsigned char val) 
-{
-#ifndef CONFIG_ETRAX_RTC_READONLY
-	int do_writereg = 1;
-#else
-	int do_writereg = 0;
-
-	if (reg == RTC_TRICKLECHARGER)
-		do_writereg = 1;
-#endif
-
-	if (do_writereg) {
-		ds1302_wenable();
-		start();
-		out_byte(0x80 | (reg << 1)); /* write register */
-		out_byte(val);
-		stop();
-		ds1302_wdisable();
-	}
-}
-
-void
-get_rtc_time(struct rtc_time *rtc_tm) 
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	rtc_tm->tm_sec = CMOS_READ(RTC_SECONDS);
-	rtc_tm->tm_min = CMOS_READ(RTC_MINUTES);
-	rtc_tm->tm_hour = CMOS_READ(RTC_HOURS);
-	rtc_tm->tm_mday = CMOS_READ(RTC_DAY_OF_MONTH);
-	rtc_tm->tm_mon = CMOS_READ(RTC_MONTH);
-	rtc_tm->tm_year = CMOS_READ(RTC_YEAR);
-
-	local_irq_restore(flags);
-	
-	rtc_tm->tm_sec = bcd2bin(rtc_tm->tm_sec);
-	rtc_tm->tm_min = bcd2bin(rtc_tm->tm_min);
-	rtc_tm->tm_hour = bcd2bin(rtc_tm->tm_hour);
-	rtc_tm->tm_mday = bcd2bin(rtc_tm->tm_mday);
-	rtc_tm->tm_mon = bcd2bin(rtc_tm->tm_mon);
-	rtc_tm->tm_year = bcd2bin(rtc_tm->tm_year);
-
-	/*
-	 * Account for differences between how the RTC uses the values
-	 * and how they are defined in a struct rtc_time;
-	 */
-
-	if (rtc_tm->tm_year <= 69)
-		rtc_tm->tm_year += 100;
-
-	rtc_tm->tm_mon--;
-}
-
-static unsigned char days_in_mo[] = 
-    {0, 31, 28, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31};
-
-/* ioctl that supports RTC_RD_TIME and RTC_SET_TIME (read and set time/date). */
-
-static int rtc_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-	unsigned long flags;
-
-	switch(cmd) {
-		case RTC_RD_TIME:	/* read the time/date from RTC	*/
-		{
-			struct rtc_time rtc_tm;
-						
-			memset(&rtc_tm, 0, sizeof (struct rtc_time));
-			get_rtc_time(&rtc_tm);						
-			if (copy_to_user((struct rtc_time*)arg, &rtc_tm, sizeof(struct rtc_time)))
-				return -EFAULT;	
-			return 0;
-		}
-
-		case RTC_SET_TIME:	/* set the RTC */
-		{
-			struct rtc_time rtc_tm;
-			unsigned char mon, day, hrs, min, sec, leap_yr;
-			unsigned int yrs;
-
-			if (!capable(CAP_SYS_TIME))
-				return -EPERM;
-
-			if (copy_from_user(&rtc_tm, (struct rtc_time*)arg, sizeof(struct rtc_time)))
-				return -EFAULT;
-
-			yrs = rtc_tm.tm_year + 1900;
-			mon = rtc_tm.tm_mon + 1;   /* tm_mon starts at zero */
-			day = rtc_tm.tm_mday;
-			hrs = rtc_tm.tm_hour;
-			min = rtc_tm.tm_min;
-			sec = rtc_tm.tm_sec;
-			
-			
-			if ((yrs < 1970) || (yrs > 2069))
-				return -EINVAL;
-
-			leap_yr = ((!(yrs % 4) && (yrs % 100)) || !(yrs % 400));
-
-			if ((mon > 12) || (day == 0))
-				return -EINVAL;
-
-			if (day > (days_in_mo[mon] + ((mon == 2) && leap_yr)))
-				return -EINVAL;
-			
-			if ((hrs >= 24) || (min >= 60) || (sec >= 60))
-				return -EINVAL;
-
-			if (yrs >= 2000)
-				yrs -= 2000;	/* RTC (0, 1, ... 69) */
-			else
-				yrs -= 1900;	/* RTC (70, 71, ... 99) */
-
-			sec = bin2bcd(sec);
-			min = bin2bcd(min);
-			hrs = bin2bcd(hrs);
-			day = bin2bcd(day);
-			mon = bin2bcd(mon);
-			yrs = bin2bcd(yrs);
-
-			local_irq_save(flags);
-			CMOS_WRITE(yrs, RTC_YEAR);
-			CMOS_WRITE(mon, RTC_MONTH);
-			CMOS_WRITE(day, RTC_DAY_OF_MONTH);
-			CMOS_WRITE(hrs, RTC_HOURS);
-			CMOS_WRITE(min, RTC_MINUTES);
-			CMOS_WRITE(sec, RTC_SECONDS);
-			local_irq_restore(flags);
-
-			/* Notice that at this point, the RTC is updated but
-			 * the kernel is still running with the old time.
-			 * You need to set that separately with settimeofday
-			 * or adjtimex.
-			 */
-			return 0;
-		}
-
-		case RTC_SET_CHARGE: /* set the RTC TRICKLE CHARGE register */
-		{
-			int tcs_val;
-
-			if (!capable(CAP_SYS_TIME))
-				return -EPERM;
-			
-			if(copy_from_user(&tcs_val, (int*)arg, sizeof(int)))
-				return -EFAULT;
-
-			tcs_val = RTC_TCR_PATTERN | (tcs_val & 0x0F);
-			ds1302_writereg(RTC_TRICKLECHARGER, tcs_val);
-			return 0;
-		}
-		case RTC_VL_READ:
-		{
-			/* TODO:
-			 * Implement voltage low detection support
-			 */
-			printk(KERN_WARNING "DS1302: RTC Voltage Low detection"
-			       " is not supported\n");
-			return 0;
-		}
-		case RTC_VL_CLR:
-		{
-			/* TODO:
-			 * Nothing to do since Voltage Low detection is not supported
-			 */
-			return 0;
-		}
-		default:
-			return -ENOIOCTLCMD;
-	}
-}
-
-static long rtc_unlocked_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-	int ret;
-
-	mutex_lock(&ds1302_mutex);
-	ret = rtc_ioctl(file, cmd, arg);
-	mutex_unlock(&ds1302_mutex);
-
-	return ret;
-}
-
-static void
-print_rtc_status(void)
-{
-	struct rtc_time tm;
-
-	get_rtc_time(&tm);
-
-	/*
-	 * There is no way to tell if the luser has the RTC set for local
-	 * time or for Universal Standard Time (GMT). Probably local though.
-	 */
-
-	printk(KERN_INFO "rtc_time\t: %02d:%02d:%02d\n",
-	       tm.tm_hour, tm.tm_min, tm.tm_sec);
-	printk(KERN_INFO "rtc_date\t: %04d-%02d-%02d\n",
-	       tm.tm_year + 1900, tm.tm_mon + 1, tm.tm_mday);
-}
-
-/* The various file operations we support. */
-
-static const struct file_operations rtc_fops = {
-	.owner		= THIS_MODULE,
-	.unlocked_ioctl = rtc_unlocked_ioctl,
-	.llseek		= noop_llseek,
-}; 
-
-/* Probe for the chip by writing something to its RAM and try reading it back. */
-
-#define MAGIC_PATTERN 0x42
-
-static int __init
-ds1302_probe(void) 
-{
-	int retval, res; 
-
-	TK_RST_DIR(1);
-	TK_SCL_DIR(1);
-	TK_SDA_DIR(0);
-	
-	/* Try to talk to timekeeper. */
-
-	ds1302_wenable();  
-	start();
-	out_byte(0xc0); /* write RAM byte 0 */	
-	out_byte(MAGIC_PATTERN); /* write something magic */
-	start();
-	out_byte(0xc1); /* read RAM byte 0 */
-
-	if((res = in_byte()) == MAGIC_PATTERN) {
-		stop();
-		ds1302_wdisable();
-		printk(KERN_INFO "%s: RTC found.\n", ds1302_name);
-		printk(KERN_INFO "%s: SDA, SCL, RST on PB%i, PB%i, %s%i\n",
-		       ds1302_name,
-		       CONFIG_ETRAX_DS1302_SDABIT,
-		       CONFIG_ETRAX_DS1302_SCLBIT,
-#ifdef CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT
-		       "GENIO",
-#else
-		       "PB",
-#endif
-		       CONFIG_ETRAX_DS1302_RSTBIT);
-		       print_rtc_status();
-		retval = 1;
-	} else {
-		stop();
-		retval = 0;
-	}
-
-	return retval;
-}
-
-
-/* Just probe for the RTC and register the device to handle the ioctl needed. */
-
-int __init
-ds1302_init(void) 
-{
-#ifdef CONFIG_ETRAX_I2C
-	i2c_init();
-#endif
-
-	if (!ds1302_probe()) {
-#ifdef CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT
-#if CONFIG_ETRAX_DS1302_RSTBIT == 27
-		/*
-		 * The only way to set g27 to output is to enable ATA.
-		 *
-		 * Make sure that R_GEN_CONFIG is setup correct.
-		 */
-		/* Allocating the ATA interface will grab almost all
-		 * pins in I/O groups a, b, c and d.  A consequence of
-		 * allocating the ATA interface is that the fixed
-		 * interfaces shared RAM, parallel port 0, parallel
-		 * port 1, parallel port W, SCSI-8 port 0, SCSI-8 port
-		 * 1, SCSI-W, serial port 2, serial port 3,
-		 * synchronous serial port 3 and USB port 2 and almost
-		 * all GPIO pins on port g cannot be used.
-		 */
-		if (cris_request_io_interface(if_ata, "ds1302/ATA")) {
-			printk(KERN_WARNING "ds1302: Failed to get IO interface\n");
-			return -1;
-		}
-
-#elif CONFIG_ETRAX_DS1302_RSTBIT == 0
-		if (cris_io_interface_allocate_pins(if_gpio_grp_a,
-						    'g',
-						    CONFIG_ETRAX_DS1302_RSTBIT,
-						    CONFIG_ETRAX_DS1302_RSTBIT)) {
-			printk(KERN_WARNING "ds1302: Failed to get IO interface\n");
-			return -1;
-		}
-
-		/* Set the direction of this bit to out. */
-		genconfig_shadow = ((genconfig_shadow &
- 				     ~IO_MASK(R_GEN_CONFIG, g0dir)) |
- 				   (IO_STATE(R_GEN_CONFIG, g0dir, out)));
-		*R_GEN_CONFIG = genconfig_shadow;
-#endif
-		if (!ds1302_probe()) {
-			printk(KERN_WARNING "%s: RTC not found.\n", ds1302_name);
-			return -1;
-		}
-#else
-		printk(KERN_WARNING "%s: RTC not found.\n", ds1302_name);
-		return -1;
-#endif
-  	}
-	/* Initialise trickle charger */
-	ds1302_writereg(RTC_TRICKLECHARGER,
-			RTC_TCR_PATTERN |(CONFIG_ETRAX_DS1302_TRICKLE_CHARGE & 0x0F));
-        /* Start clock by resetting CLOCK_HALT */
-	ds1302_writereg(RTC_SECONDS, (ds1302_readreg(RTC_SECONDS) & 0x7F));
-	return 0;
-}
-
-static int __init ds1302_register(void)
-{
-	ds1302_init();
-	if (register_chrdev(RTC_MAJOR_NR, ds1302_name, &rtc_fops)) {
-		printk(KERN_INFO "%s: unable to get major %d for rtc\n", 
-		       ds1302_name, RTC_MAJOR_NR);
-		return -1;
-	}
-        return 0;
-
-}
-
-module_init(ds1302_register);
diff --git a/arch/cris/arch-v10/drivers/pcf8563.c b/arch/cris/arch-v10/drivers/pcf8563.c
deleted file mode 100644
index 9da056860c92..000000000000
--- a/arch/cris/arch-v10/drivers/pcf8563.c
+++ /dev/null
@@ -1,380 +0,0 @@
-/*
- * PCF8563 RTC
- *
- * From Phillips' datasheet:
- *
- * The PCF8563 is a CMOS real-time clock/calendar optimized for low power
- * consumption. A programmable clock output, interrupt output and voltage
- * low detector are also provided. All address and data are transferred
- * serially via two-line bidirectional I2C-bus. Maximum bus speed is
- * 400 kbits/s. The built-in word address register is incremented
- * automatically after each written or read byte.
- *
- * Copyright (c) 2002-2007, Axis Communications AB
- * All rights reserved.
- *
- * Author: Tobias Anderberg <tobiasa@axis.com>.
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/sched.h>
-#include <linux/init.h>
-#include <linux/fs.h>
-#include <linux/ioctl.h>
-#include <linux/delay.h>
-#include <linux/bcd.h>
-#include <linux/mutex.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
-#include <asm/rtc.h>
-
-#include "i2c.h"
-
-#define PCF8563_MAJOR 121	/* Local major number. */
-#define DEVICE_NAME "rtc"	/* Name which is registered in /proc/devices. */
-#define PCF8563_NAME "PCF8563"
-#define DRIVER_VERSION "$Revision: 1.24 $"
-
-/* I2C bus slave registers. */
-#define RTC_I2C_READ		0xa3
-#define RTC_I2C_WRITE		0xa2
-
-/* Two simple wrapper macros, saves a few keystrokes. */
-#define rtc_read(x) i2c_readreg(RTC_I2C_READ, x)
-#define rtc_write(x,y) i2c_writereg(RTC_I2C_WRITE, x, y)
-
-static DEFINE_MUTEX(pcf8563_mutex);
-static DEFINE_MUTEX(rtc_lock); /* Protect state etc */
-
-static const unsigned char days_in_month[] =
-	{ 0, 31, 28, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31 };
-
-static long pcf8563_unlocked_ioctl(struct file *, unsigned int, unsigned long);
-
-/* Cache VL bit value read at driver init since writing the RTC_SECOND
- * register clears the VL status.
- */
-static int voltage_low;
-
-static const struct file_operations pcf8563_fops = {
-	.owner = THIS_MODULE,
-	.unlocked_ioctl = pcf8563_unlocked_ioctl,
-	.llseek		= noop_llseek,
-};
-
-unsigned char
-pcf8563_readreg(int reg)
-{
-	unsigned char res = rtc_read(reg);
-
-	/* The PCF8563 does not return 0 for unimplemented bits. */
-	switch (reg) {
-	case RTC_SECONDS:
-	case RTC_MINUTES:
-		res &= 0x7F;
-		break;
-	case RTC_HOURS:
-	case RTC_DAY_OF_MONTH:
-		res &= 0x3F;
-		break;
-	case RTC_WEEKDAY:
-		res &= 0x07;
-		break;
-	case RTC_MONTH:
-		res &= 0x1F;
-		break;
-	case RTC_CONTROL1:
-		res &= 0xA8;
-		break;
-	case RTC_CONTROL2:
-		res &= 0x1F;
-		break;
-	case RTC_CLOCKOUT_FREQ:
-	case RTC_TIMER_CONTROL:
-		res &= 0x83;
-		break;
-	}
-	return res;
-}
-
-void
-pcf8563_writereg(int reg, unsigned char val)
-{
-	rtc_write(reg, val);
-}
-
-void
-get_rtc_time(struct rtc_time *tm)
-{
-	tm->tm_sec  = rtc_read(RTC_SECONDS);
-	tm->tm_min  = rtc_read(RTC_MINUTES);
-	tm->tm_hour = rtc_read(RTC_HOURS);
-	tm->tm_mday = rtc_read(RTC_DAY_OF_MONTH);
-	tm->tm_wday = rtc_read(RTC_WEEKDAY);
-	tm->tm_mon  = rtc_read(RTC_MONTH);
-	tm->tm_year = rtc_read(RTC_YEAR);
-
-	if (tm->tm_sec & 0x80) {
-		printk(KERN_ERR "%s: RTC Voltage Low - reliable date/time "
-		       "information is no longer guaranteed!\n", PCF8563_NAME);
-	}
-
-	tm->tm_year  = bcd2bin(tm->tm_year) +
-		       ((tm->tm_mon & 0x80) ? 100 : 0);
-	tm->tm_sec  &= 0x7F;
-	tm->tm_min  &= 0x7F;
-	tm->tm_hour &= 0x3F;
-	tm->tm_mday &= 0x3F;
-	tm->tm_wday &= 0x07; /* Not coded in BCD. */
-	tm->tm_mon  &= 0x1F;
-
-	tm->tm_sec = bcd2bin(tm->tm_sec);
-	tm->tm_min = bcd2bin(tm->tm_min);
-	tm->tm_hour = bcd2bin(tm->tm_hour);
-	tm->tm_mday = bcd2bin(tm->tm_mday);
-	tm->tm_mon = bcd2bin(tm->tm_mon);
-	tm->tm_mon--; /* Month is 1..12 in RTC but 0..11 in linux */
-}
-
-int __init
-pcf8563_init(void)
-{
-	static int res;
-	static int first = 1;
-
-	if (!first)
-		return res;
-	first = 0;
-
-	/* Initiate the i2c protocol. */
-	res = i2c_init();
-	if (res < 0) {
-		printk(KERN_CRIT "pcf8563_init: Failed to init i2c.\n");
-		return res;
-	}
-
-	/*
-	 * First of all we need to reset the chip. This is done by
-	 * clearing control1, control2 and clk freq and resetting
-	 * all alarms.
-	 */
-	if (rtc_write(RTC_CONTROL1, 0x00) < 0)
-		goto err;
-
-	if (rtc_write(RTC_CONTROL2, 0x00) < 0)
-		goto err;
-
-	if (rtc_write(RTC_CLOCKOUT_FREQ, 0x00) < 0)
-		goto err;
-
-	if (rtc_write(RTC_TIMER_CONTROL, 0x03) < 0)
-		goto err;
-
-	/* Reset the alarms. */
-	if (rtc_write(RTC_MINUTE_ALARM, 0x80) < 0)
-		goto err;
-
-	if (rtc_write(RTC_HOUR_ALARM, 0x80) < 0)
-		goto err;
-
-	if (rtc_write(RTC_DAY_ALARM, 0x80) < 0)
-		goto err;
-
-	if (rtc_write(RTC_WEEKDAY_ALARM, 0x80) < 0)
-		goto err;
-
-	/* Check for low voltage, and warn about it. */
-	if (rtc_read(RTC_SECONDS) & 0x80) {
-		voltage_low = 1;
-		printk(KERN_WARNING "%s: RTC Voltage Low - reliable "
-		       "date/time information is no longer guaranteed!\n",
-		       PCF8563_NAME);
-	}
-
-	return res;
-
-err:
-	printk(KERN_INFO "%s: Error initializing chip.\n", PCF8563_NAME);
-	res = -1;
-	return res;
-}
-
-void __exit
-pcf8563_exit(void)
-{
-	unregister_chrdev(PCF8563_MAJOR, DEVICE_NAME);
-}
-
-/*
- * ioctl calls for this driver. Why return -ENOTTY upon error? Because
- * POSIX says so!
- */
-static int pcf8563_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
-{
-	/* Some sanity checks. */
-	if (_IOC_TYPE(cmd) != RTC_MAGIC)
-		return -ENOTTY;
-
-	if (_IOC_NR(cmd) > RTC_MAX_IOCTL)
-		return -ENOTTY;
-
-	switch (cmd) {
-	case RTC_RD_TIME:
-	{
-		struct rtc_time tm;
-
-		mutex_lock(&rtc_lock);
-		memset(&tm, 0, sizeof tm);
-		get_rtc_time(&tm);
-
-		if (copy_to_user((struct rtc_time *) arg, &tm,
-				 sizeof tm)) {
-			mutex_unlock(&rtc_lock);
-			return -EFAULT;
-		}
-
-		mutex_unlock(&rtc_lock);
-
-		return 0;
-	}
-	case RTC_SET_TIME:
-	{
-		int leap;
-		int year;
-		int century;
-		struct rtc_time tm;
-
-		memset(&tm, 0, sizeof tm);
-		if (!capable(CAP_SYS_TIME))
-			return -EPERM;
-
-		if (copy_from_user(&tm, (struct rtc_time *) arg, sizeof tm))
-			return -EFAULT;
-
-		/* Convert from struct tm to struct rtc_time. */
-		tm.tm_year += 1900;
-		tm.tm_mon += 1;
-
-		/*
-		 * Check if tm.tm_year is a leap year. A year is a leap
-		 * year if it is divisible by 4 but not 100, except
-		 * that years divisible by 400 _are_ leap years.
-		 */
-		year = tm.tm_year;
-		leap = (tm.tm_mon == 2) &&
-			((year % 4 == 0 && year % 100 != 0) || year % 400 == 0);
-
-		/* Perform some sanity checks. */
-		if ((tm.tm_year < 1970) ||
-		    (tm.tm_mon > 12) ||
-		    (tm.tm_mday == 0) ||
-		    (tm.tm_mday > days_in_month[tm.tm_mon] + leap) ||
-		    (tm.tm_wday >= 7) ||
-		    (tm.tm_hour >= 24) ||
-		    (tm.tm_min >= 60) ||
-		    (tm.tm_sec >= 60))
-			return -EINVAL;
-
-		century = (tm.tm_year >= 2000) ? 0x80 : 0;
-		tm.tm_year = tm.tm_year % 100;
-
-		tm.tm_year = bin2bcd(tm.tm_year);
-		tm.tm_mon = bin2bcd(tm.tm_mon);
-		tm.tm_mday = bin2bcd(tm.tm_mday);
-		tm.tm_hour = bin2bcd(tm.tm_hour);
-		tm.tm_min = bin2bcd(tm.tm_min);
-		tm.tm_sec = bin2bcd(tm.tm_sec);
-		tm.tm_mon |= century;
-
-		mutex_lock(&rtc_lock);
-
-		rtc_write(RTC_YEAR, tm.tm_year);
-		rtc_write(RTC_MONTH, tm.tm_mon);
-		rtc_write(RTC_WEEKDAY, tm.tm_wday); /* Not coded in BCD. */
-		rtc_write(RTC_DAY_OF_MONTH, tm.tm_mday);
-		rtc_write(RTC_HOURS, tm.tm_hour);
-		rtc_write(RTC_MINUTES, tm.tm_min);
-		rtc_write(RTC_SECONDS, tm.tm_sec);
-
-		mutex_unlock(&rtc_lock);
-
-		return 0;
-	}
-	case RTC_VL_READ:
-		if (voltage_low) {
-			printk(KERN_ERR "%s: RTC Voltage Low - "
-			       "reliable date/time information is no "
-			       "longer guaranteed!\n", PCF8563_NAME);
-		}
-
-		if (copy_to_user((int *) arg, &voltage_low, sizeof(int)))
-			return -EFAULT;
-		return 0;
-
-	case RTC_VL_CLR:
-	{
-		/* Clear the VL bit in the seconds register in case
-		 * the time has not been set already (which would
-		 * have cleared it). This does not really matter
-		 * because of the cached voltage_low value but do it
-		 * anyway for consistency. */
-
-		int ret = rtc_read(RTC_SECONDS);
-
-		rtc_write(RTC_SECONDS, (ret & 0x7F));
-
-		/* Clear the cached value. */
-		voltage_low = 0;
-
-		return 0;
-	}
-	default:
-		return -ENOTTY;
-	}
-
-	return 0;
-}
-
-static long pcf8563_unlocked_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
-{
-	int ret;
-
-	mutex_lock(&pcf8563_mutex);
-	ret = pcf8563_ioctl(filp, cmd, arg);
-	mutex_unlock(&pcf8563_mutex);
-
-	return ret;
-}
-
-static int __init pcf8563_register(void)
-{
-	if (pcf8563_init() < 0) {
-		printk(KERN_INFO "%s: Unable to initialize Real-Time Clock "
-		       "Driver, %s\n", PCF8563_NAME, DRIVER_VERSION);
-		return -1;
-	}
-
-	if (register_chrdev(PCF8563_MAJOR, DEVICE_NAME, &pcf8563_fops) < 0) {
-		printk(KERN_INFO "%s: Unable to get major number %d for RTC device.\n",
-		       PCF8563_NAME, PCF8563_MAJOR);
-		return -1;
-	}
-
-	printk(KERN_INFO "%s Real-Time Clock Driver, %s\n", PCF8563_NAME,
-	       DRIVER_VERSION);
-
-	/* Check for low voltage, and warn about it. */
-	if (voltage_low) {
-		printk(KERN_WARNING "%s: RTC Voltage Low - reliable date/time "
-		       "information is no longer guaranteed!\n", PCF8563_NAME);
-	}
-
-	return 0;
-}
-
-module_init(pcf8563_register);
-module_exit(pcf8563_exit);