m68knommu: remove MBAR and IPSBAR hacks for the ColdFire 520x CPUs

The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>

2 files changed, 20 insertions, 20 deletions

diff --git a/arch/m68knommu/platform/520x/config.c b/arch/m68knommu/platform/520x/config.c
index 71d2ba474c63..621238f1a219 100644
--- a/arch/m68knommu/platform/520x/config.c
+++ b/arch/m68knommu/platform/520x/config.c
@@ -27,15 +27,15 @@
 
 static struct mcf_platform_uart m520x_uart_platform[] = {
 	{
-		.mapbase	= MCF_MBAR + MCFUART_BASE1,
+		.mapbase	= MCFUART_BASE1,
 		.irq		= MCFINT_VECBASE + MCFINT_UART0,
 	},
 	{
-		.mapbase 	= MCF_MBAR + MCFUART_BASE2,
+		.mapbase 	= MCFUART_BASE2,
 		.irq		= MCFINT_VECBASE + MCFINT_UART1,
 	},
 	{
-		.mapbase 	= MCF_MBAR + MCFUART_BASE3,
+		.mapbase 	= MCFUART_BASE3,
 		.irq		= MCFINT_VECBASE + MCFINT_UART2,
 	},
 	{ },
@@ -49,8 +49,8 @@ static struct platform_device m520x_uart = {
 
 static struct resource m520x_fec_resources[] = {
 	{
-		.start		= MCF_MBAR + 0x30000,
-		.end		= MCF_MBAR + 0x30000 + 0x7ff,
+		.start		= MCFFEC_BASE,
+		.end		= MCFFEC_BASE + MCFFEC_SIZE - 1,
 		.flags		= IORESOURCE_MEM,
 	},
 	{
@@ -208,11 +208,11 @@ static void __init m520x_qspi_init(void)
 {
 	u16 par;
 	/* setup Port QS for QSPI with gpio CS control */
-	writeb(0x3f, MCF_IPSBAR + MCF_GPIO_PAR_QSPI);
+	writeb(0x3f, MCF_GPIO_PAR_QSPI);
 	/* make U1CTS and U2RTS gpio for cs_control */
-	par = readw(MCF_IPSBAR + MCF_GPIO_PAR_UART);
+	par = readw(MCF_GPIO_PAR_UART);
 	par &= 0x00ff;
-	writew(par, MCF_IPSBAR + MCF_GPIO_PAR_UART);
+	writew(par, MCF_GPIO_PAR_UART);
 }
 #endif /* defined(CONFIG_SPI_COLDFIRE_QSPI) || defined(CONFIG_SPI_COLDFIRE_QSPI_MODULE) */
 
@@ -234,23 +234,23 @@ static void __init m520x_uart_init_line(int line, int irq)
 
 	switch (line) {
 	case 0:
-		par = readw(MCF_IPSBAR + MCF_GPIO_PAR_UART);
+		par = readw(MCF_GPIO_PAR_UART);
 		par |= MCF_GPIO_PAR_UART_PAR_UTXD0 |
 		       MCF_GPIO_PAR_UART_PAR_URXD0;
-		writew(par, MCF_IPSBAR + MCF_GPIO_PAR_UART);
+		writew(par, MCF_GPIO_PAR_UART);
 		break;
 	case 1:
-		par = readw(MCF_IPSBAR + MCF_GPIO_PAR_UART);
+		par = readw(MCF_GPIO_PAR_UART);
 		par |= MCF_GPIO_PAR_UART_PAR_UTXD1 |
 		       MCF_GPIO_PAR_UART_PAR_URXD1;
-		writew(par, MCF_IPSBAR + MCF_GPIO_PAR_UART);
+		writew(par, MCF_GPIO_PAR_UART);
 		break;
 	case 2:
-		par2 = readb(MCF_IPSBAR + MCF_GPIO_PAR_FECI2C);
+		par2 = readb(MCF_GPIO_PAR_FECI2C);
 		par2 &= ~0x0F;
 		par2 |= MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2 |
 			MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2;
-		writeb(par2, MCF_IPSBAR + MCF_GPIO_PAR_FECI2C);
+		writeb(par2, MCF_GPIO_PAR_FECI2C);
 		break;
 	}
 }
@@ -271,11 +271,11 @@ static void __init m520x_fec_init(void)
 	u8 v;
 
 	/* Set multi-function pins to ethernet mode */
-	v = readb(MCF_IPSBAR + MCF_GPIO_PAR_FEC);
-	writeb(v | 0xf0, MCF_IPSBAR + MCF_GPIO_PAR_FEC);
+	v = readb(MCF_GPIO_PAR_FEC);
+	writeb(v | 0xf0, MCF_GPIO_PAR_FEC);
 
-	v = readb(MCF_IPSBAR + MCF_GPIO_PAR_FECI2C);
-	writeb(v | 0x0f, MCF_IPSBAR + MCF_GPIO_PAR_FECI2C);
+	v = readb(MCF_GPIO_PAR_FECI2C);
+	writeb(v | 0x0f, MCF_GPIO_PAR_FECI2C);
 }
 
 /***************************************************************************/
diff --git a/arch/m68knommu/platform/coldfire/head.S b/arch/m68knommu/platform/coldfire/head.S
index d5977909ae5f..7967e8ab9fae 100644
--- a/arch/m68knommu/platform/coldfire/head.S
+++ b/arch/m68knommu/platform/coldfire/head.S
@@ -68,14 +68,14 @@
 #elif defined(CONFIG_M520x)
 .macro GET_MEM_SIZE
 	clrl	%d0
-	movel	MCF_MBAR+MCFSIM_SDCS0, %d2 /* Get SDRAM chip select 0 config */
+	movel	MCFSIM_SDCS0, %d2	/* Get SDRAM chip select 0 config */
 	andl	#0x1f, %d2		/* Get only the chip select size */
 	beq	3f			/* Check if it is enabled */
 	addql	#1, %d2			/* Form exponent */
 	moveql	#1, %d0
 	lsll	%d2, %d0		/* 2 ^ exponent */
 3:
-	movel	MCF_MBAR+MCFSIM_SDCS1, %d2 /* Get SDRAM chip select 1 config */
+	movel	MCFSIM_SDCS1, %d2	/* Get SDRAM chip select 1 config */
 	andl	#0x1f, %d2		/* Get only the chip select size */
 	beq	4f			/* Check if it is enabled */
 	addql	#1, %d2			/* Form exponent */