Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:

 o Add basic support for the Mediatek/Ralink Wireless SoC family.

 o The Qualcomm Atheros platform is extended by support for the new
   QCA955X SoC series as well as a bunch of patches that get the code
   ready for OF support.

 o Lantiq and BCM47XX platform have a few improvements and bug fixes.

 o MIPS has sent a few patches that get the kernel ready for the
   upcoming microMIPS support.

 o The rest of the series is made up of small bug fixes and cleanups
   that relate to various parts of the MIPS code.  The biggy in there is
   a whitespace cleanup.  After I was sent another set of whitespace
   cleanup patches I decided it was the time to clean the whitespace
   "issues" for once and and that touches many files below arch/mips/.

Fix up silly conflicts, mostly due to whitespace cleanups.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
  MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
  MIPS: remove broken conditional inside vpe loader code
  MIPS: SMTC: fix implicit declaration of set_vi_handler
  MIPS: early_printk: drop __init annotations
  MIPS: Probe for and report hardware virtualization support.
  MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
  MIPS: ath79: add USB controller registration code for the QCA955X SoCs
  MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
  MIPS: ath79: add WMAC registration code for the QCA955X SoCs
  MIPS: ath79: register UART for the QCA955X SoCs
  MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
  MIPS: ath79: add GPIO setup code for the QCA955X SoCs
  MIPS: ath79: add IRQ handling code for the QCA955X SoCs
  MIPS: ath79: add clock setup code for the QCA955X SoCs
  MIPS: ath79: add SoC detection code for the QCA955X SoCs
  MIPS: ath79: add early printk support for the QCA955X SoCs
  MIPS: ath79: fix WMAC IRQ resource assignment
  mips: reserve elfcorehdr
  mips: Make sure kernel memory is in iomem
  MIPS: ath79: use dynamically allocated USB platform devices
  ...

1 files changed, 216 insertions, 0 deletions

diff --git a/arch/mips/pmcs-msp71xx/gpio.c b/arch/mips/pmcs-msp71xx/gpio.c
new file mode 100644
index 000000000000..aaccbe524386
--- /dev/null
+++ b/arch/mips/pmcs-msp71xx/gpio.c
@@ -0,0 +1,216 @@
+/*
+ * Generic PMC MSP71xx GPIO handling. These base gpio are controlled by two
+ * types of registers. The data register sets the output level when in output
+ * mode and when in input mode will contain the value at the input. The config
+ * register sets the various modes for each gpio.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * @author Patrick Glass <patrickglass@gmail.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+
+#define MSP71XX_CFG_OFFSET(gpio)	(4 * (gpio))
+#define CONF_MASK			0x0F
+#define MSP71XX_GPIO_INPUT		0x01
+#define MSP71XX_GPIO_OUTPUT		0x08
+
+#define MSP71XX_GPIO_BASE		0x0B8400000L
+
+#define to_msp71xx_gpio_chip(c) container_of(c, struct msp71xx_gpio_chip, chip)
+
+static spinlock_t gpio_lock;
+
+/*
+ * struct msp71xx_gpio_chip - container for gpio chip and registers
+ * @chip: chip structure for the specified gpio bank
+ * @data_reg: register for reading and writing the gpio pin value
+ * @config_reg: register to set the mode for the gpio pin bank
+ * @out_drive_reg: register to set the output drive mode for the gpio pin bank
+ */
+struct msp71xx_gpio_chip {
+	struct gpio_chip chip;
+	void __iomem *data_reg;
+	void __iomem *config_reg;
+	void __iomem *out_drive_reg;
+};
+
+/*
+ * msp71xx_gpio_get() - return the chip's gpio value
+ * @chip: chip structure which controls the specified gpio
+ * @offset: gpio whose value will be returned
+ *
+ * It will return 0 if gpio value is low and other if high.
+ */
+static int msp71xx_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
+
+	return __raw_readl(msp_chip->data_reg) & (1 << offset);
+}
+
+/*
+ * msp71xx_gpio_set() - set the output value for the gpio
+ * @chip: chip structure who controls the specified gpio
+ * @offset: gpio whose value will be assigned
+ * @value: logic level to assign to the gpio initially
+ *
+ * This will set the gpio bit specified to the desired value. It will set the
+ * gpio pin low if value is 0 otherwise it will be high.
+ */
+static void msp71xx_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
+	unsigned long flags;
+	u32 data;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	data = __raw_readl(msp_chip->data_reg);
+	if (value)
+		data |= (1 << offset);
+	else
+		data &= ~(1 << offset);
+	__raw_writel(data, msp_chip->data_reg);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+}
+
+/*
+ * msp71xx_set_gpio_mode() - declare the mode for a gpio
+ * @chip: chip structure which controls the specified gpio
+ * @offset: gpio whose value will be assigned
+ * @mode: desired configuration for the gpio (see datasheet)
+ *
+ * It will set the gpio pin config to the @mode value passed in.
+ */
+static int msp71xx_set_gpio_mode(struct gpio_chip *chip,
+				 unsigned offset, int mode)
+{
+	struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
+	const unsigned bit_offset = MSP71XX_CFG_OFFSET(offset);
+	unsigned long flags;
+	u32 cfg;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	cfg = __raw_readl(msp_chip->config_reg);
+	cfg &= ~(CONF_MASK << bit_offset);
+	cfg |= (mode << bit_offset);
+	__raw_writel(cfg, msp_chip->config_reg);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	return 0;
+}
+
+/*
+ * msp71xx_direction_output() - declare the direction mode for a gpio
+ * @chip: chip structure which controls the specified gpio
+ * @offset: gpio whose value will be assigned
+ * @value: logic level to assign to the gpio initially
+ *
+ * This call will set the mode for the @gpio to output. It will set the
+ * gpio pin low if value is 0 otherwise it will be high.
+ */
+static int msp71xx_direction_output(struct gpio_chip *chip,
+				    unsigned offset, int value)
+{
+	msp71xx_gpio_set(chip, offset, value);
+
+	return msp71xx_set_gpio_mode(chip, offset, MSP71XX_GPIO_OUTPUT);
+}
+
+/*
+ * msp71xx_direction_input() - declare the direction mode for a gpio
+ * @chip: chip structure which controls the specified gpio
+ * @offset: gpio whose to which the value will be assigned
+ *
+ * This call will set the mode for the @gpio to input.
+ */
+static int msp71xx_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	return msp71xx_set_gpio_mode(chip, offset, MSP71XX_GPIO_INPUT);
+}
+
+/*
+ * msp71xx_set_output_drive() - declare the output drive for the gpio line
+ * @gpio: gpio pin whose output drive you wish to modify
+ * @value: zero for active drain 1 for open drain drive
+ *
+ * This call will set the output drive mode for the @gpio to output.
+ */
+int msp71xx_set_output_drive(unsigned gpio, int value)
+{
+	unsigned long flags;
+	u32 data;
+
+	if (gpio > 15 || gpio < 0)
+		return -EINVAL;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	data = __raw_readl((void __iomem *)(MSP71XX_GPIO_BASE + 0x190));
+	if (value)
+		data |= (1 << gpio);
+	else
+		data &= ~(1 << gpio);
+	__raw_writel(data, (void __iomem *)(MSP71XX_GPIO_BASE + 0x190));
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(msp71xx_set_output_drive);
+
+#define MSP71XX_GPIO_BANK(name, dr, cr, base_gpio, num_gpio) \
+{ \
+	.chip = { \
+		.label		  = name, \
+		.direction_input  = msp71xx_direction_input, \
+		.direction_output = msp71xx_direction_output, \
+		.get		  = msp71xx_gpio_get, \
+		.set		  = msp71xx_gpio_set, \
+		.base		  = base_gpio, \
+		.ngpio		  = num_gpio \
+	}, \
+	.data_reg	= (void __iomem *)(MSP71XX_GPIO_BASE + dr), \
+	.config_reg	= (void __iomem *)(MSP71XX_GPIO_BASE + cr), \
+	.out_drive_reg	= (void __iomem *)(MSP71XX_GPIO_BASE + 0x190), \
+}
+
+/*
+ * struct msp71xx_gpio_banks[] - container array of gpio banks
+ * @chip: chip structure for the specified gpio bank
+ * @data_reg: register for reading and writing the gpio pin value
+ * @config_reg: register to set the mode for the gpio pin bank
+ *
+ * This array structure defines the gpio banks for the PMC MIPS Processor.
+ * We specify the bank name, the data register, the config register, base
+ * starting gpio number, and the number of gpios exposed by the bank.
+ */
+static struct msp71xx_gpio_chip msp71xx_gpio_banks[] = {
+
+	MSP71XX_GPIO_BANK("GPIO_1_0", 0x170, 0x180, 0, 2),
+	MSP71XX_GPIO_BANK("GPIO_5_2", 0x174, 0x184, 2, 4),
+	MSP71XX_GPIO_BANK("GPIO_9_6", 0x178, 0x188, 6, 4),
+	MSP71XX_GPIO_BANK("GPIO_15_10", 0x17C, 0x18C, 10, 6),
+};
+
+void __init msp71xx_init_gpio(void)
+{
+	int i;
+
+	spin_lock_init(&gpio_lock);
+
+	for (i = 0; i < ARRAY_SIZE(msp71xx_gpio_banks); i++)
+		gpiochip_add(&msp71xx_gpio_banks[i].chip);
+}